Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)

ISO 10512:2012 specifies the characteristics of prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread with nominal thread diameters, D, from 8 mm up to and including 36 mm, in product grade A for diamter sizes up to and including 16 mm and product grade B for diameter sizes above 16 mm, and with property classes 6, 8 and 10.

Sechskantmuttern mit Klemmteil (mit nichtmetallischem Einsatz) mit metrischem Feingewinde - Festigkeitsklassen 6, 8 und 10 (ISO 10512:2012)

Diese Internationale Norm legt die Eigenschaften von Sechskantmuttern mit Klemmteil (mit nichtmetallischem Einsatz) mit Feingewinde mit Gewindenenndurchmessern D von 8 mm bis 36 mm, in Produktklasse A für Größen D bis 16 mm und Produktklasse B für Größen D über 16 mm, und mit Festigkeitsklassen 6, 8 und 10 fest.
Werden andere Festlegungen benötigt, können diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 724, ISO 898 2, ISO 965 2, ISO 2320 und ISO 4759 1.
ANMERKUNG 1   Die Maße der Muttern entsprechen den in ISO 8673 angegebenen Maßen, plus Klemmteil.
ANMERKUNG 2   Da die Höhe der Mutter aufgrund des Feingewindes unzureichend ist, besteht eine erhöhte Wahr-scheinlichkeit für das Abstreifen des Gewindes. Daher werden vorzugsweise hohe Muttern (Typ 2) nach ISO 7041 ver-wendet.

Écrous hexagonaux normaux autofreinés (à anneau non métallique) à filetage métrique à pas fin - Classes de qualité 6, 8 et 10 (ISO 10512:2012)

L'ISO 10512:2012 spécifie les caractéristiques des écrous hexagonaux normaux autofreinés (à anneau non métallique) à filetage métrique à pas fin, de diamètre de filetage D de 8 mm à 36 mm inclus, de grade A pour les diamètres D jusqu'à 16 mm et de grade B pour les diamètres D supérieurs à 16 mm, et de classes de qualité 6, 8 et 10.

Šestrobe zaščitne matice (s plastičnim vložkom) z drobnim metrskim navojem - Razredi trdnosti 6, 8 in 10 (ISO 10512:2012)

Ta mednarodni standard določa značilnosti šestrobih zaščitnih matic (s plastičnim vložkom) z drobnim metrskim navojem z nazivnimi premeri navoja od 8 mm do vključno 36 mm, v razredu izdelave A za velikosti premera do vključno 16 mm in v razredu izdelave B za velikosti premera nad 16 mm, ter z razredi trdnosti 6, 8 in 10. Če so zahtevane druge specifikacije, jih je mogoče izbrati iz obstoječih mednarodnih standardov, na primer standardov ISO 261, ISO 724, ISO 898-2, ISO 965-2, ISO 2320 in ISO 4759-1.

General Information

Status
Published
Publication Date
18-Dec-2012
Withdrawal Date
29-Jun-2013
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
19-Dec-2012
Completion Date
19-Dec-2012

Relations

Buy Standard

Standard
EN ISO 10512:2013
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2013
1DGRPHãþD
SIST EN ISO 10512:2001
âHVWUREH]DãþLWQHPDWLFH VSODVWLþQLPYORåNRP ]GUREQLPPHWUVNLPQDYRMHP
5D]UHGLWUGQRVWLLQ ,62
Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine
pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)
Sechskantmuttern mit Klemmteil (mit nichtmetallischem Einsatz) mit metrischem
Feingewinde - Festigkeitsklassen 6, 8 und 10 (ISO 10512:2012)
Écrous hexagonaux normaux autofreinés (à anneau non métallique) à filetage métrique
à pas fin - Classes de qualité 6, 8 et 10 (ISO 10512:2012)
Ta slovenski standard je istoveten z: EN ISO 10512:2012
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10512
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 21.060.20 Supersedes EN ISO 10512:1997
English Version
Prevailing torque type hexagon regular nuts (with non-metallic
insert) with metric fine pitch thread - Property classes 6, 8 and
10 (ISO 10512:2012)
Écrous hexagonaux normaux autofreinés (à anneau non Sechskantmuttern mit Klemmteil (mit nichtmetallischem
métallique) à filetage métrique à pas fin - Classes de Einsatz), Typ 1, mit metrischem Feingewinde -
qualité 6, 8 et 10 (ISO 10512:2012) Festigkeitsklassen 6, 8 und 10 (ISO 10512:2012)
This European Standard was approved by CEN on 3 December 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10512:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 10512:2012) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10512:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10512:2012 has been approved by CEN as a EN ISO 10512:2012 without any modification.

INTERNATIONAL ISO
STANDARD 10512
Second edition
2012-12-15
Prevailing torque type hexagon regular
nuts (with non-metallic insert) with
metric fine pitch thread — Property
classes 6, 8 and 10
Écrous hexagonaux normaux autofreinés (à anneau non métallique) à
filetage métrique à pas fin — Classes de qualité 6, 8 et 10
Reference number
ISO 10512:2012(E)
©
ISO 2012
ISO 10512:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 10512:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
4 Requirements and reference International Standards . 3
5 Designation .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.