Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 2: Concept phase (ISO 25119-2:2019)

This document specifies the concept phase of the development of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry and on self-propelled ride-on machines and mounted, semi-mounted and trailed machines used in agriculture. It can also be applied to mobile municipal equipment (such as street-sweeping machines).
This document is not applicable to:
—          aircraft and air-cushion vehicles used in agriculture;
—          lawn and garden equipment.
This document specifies the characteristics and categories required of SRP/CS for carrying out their safety-related functions. It does not identify performance levels for specific applications.
NOTE 1    Machine specific type-C standards can specify performance levels (AgPL) for safety-related functions in machines within their scope. Otherwise, the specification of AgPL is the responsibility of the manufacturer.
This document is applicable to the safety-related parts of electrical/electronic/programmable electronic systems (E/E/PES), as these relate to mechatronic systems. It covers the possible hazards caused by malfunctioning behaviour of E/E/PES safety-related systems, including interaction of these systems. It does not address hazards related to electric shock, fire, smoke, heat, radiation, toxicity, flammability, reactivity, corrosion, release of energy, and similar hazards., unless directly caused by malfunctioning behaviour of E/E/PES safety-related systems. It also covers malfunctioning behaviour of E/E/PES safety-related systems involved in protection measures, safeguards, or safety-related functions in response to non-E/E/PES hazards.
Examples included within the scope of this document:
—          SRP/CS's limiting current flow in electric hybrids to prevent insulation failure/shock hazards;
—          electromagnetic interference with the SRP/CS;
—           SRP/CS's designed to prevent fire.
Examples not included within the scope of this document:
—          insulation failure due to friction that leads to electric shock hazards;
—          nominal electromagnetic radiation impacting nearby machine control systems;
—          corrosion causing electric cables to overheat.
This document is not applicable to non-E/E/PES systems (such as hydraulic, mechanic or pneumatic).
NOTE 2    See also ISO 12100 for design principles related to the safety of machinery.
This document is not applicable to safety-related parts of control systems manufactured before the date of its publication.

Traktoren und Maschinen für die Land- und Forstwirtschaft - Sicherheitsbezogene Teile von Steuerungen - Teil 2: Konzeptphase (ISO 25119-2:2019)

Dieses Dokument legt die Konzeptphase der Entwicklung sicherheitsbezogener Teile von Steuerungen (SRP/CS) in land- und forstwirtschaftlichen Traktoren, selbstfahrenden Aufsitzmaschinen sowie landwirtschaftlich genutzten Anbau-, Aufsattel- und Anhängemaschinen fest. Es kann auch auf fahrbare kommunale Geräte (z. B. Straßenkehrmaschinen) angewendet werden.
Dieses Dokument ist nicht anwendbar für:
-   Flugzeuge und Luftkissenfahrzeuge für den landwirtschaftlichen Einsatz;
-   Rasen- und Gartengeräte.
Dieses Dokument legt die Merkmale und Kategorien von SRP/CS fest, die zur Ausführung von Sicherheitsfunktionen erforderlich sind. Es enthält keine Performance-Level für bestimmte Anwendungen.
ANMERKUNG 1   Maschinenspezifische Typ C Normen können in ihrem Anwendungsbereich Performance-Level (AgPL) für Sicherheitsfunktionen von Maschinen festlegen. Andernfalls ist der Hersteller für die Festlegung der AgPL verantwortlich.
Dieses Dokument ist für sicherheitsbezogene Teile elektrischer/elektronischer/programmierbarer elektronischer Systeme (E/E/PES) als Teil mechatronischer Systeme anwendbar. Es behandelt die möglichen Gefahren durch Fehlfunktionen von sicherheitsbezogenen E/E/PES einschließlich der Wechselwirkungen dieser Systeme. Es behandelt keine Gefährdungen in Verbindung mit Stromschlag, Feuer, Rauch, Hitze, Strahlung, Toxizität, Entflammbarkeit, Reaktivität, Korrosion, Freisetzung von Energie usw., außer wenn diese direkt durch eine Fehlfunktion der sicherheitsbezogenen Systeme von E/E/PES verursacht werden. Darüber hinaus behandelt das Dokument die Fehlfunktionen sicherheitsbezogener Systeme von E/E/PES, die an Schutzmaßnahmen, Schutzeinrichtungen oder Sicherheitsfunktionen als Reaktion auf nicht durch E/E/PES verursachte Gefährdungen beteiligt sind.
Im Anwendungsbereich dieses Dokuments enthaltene Beispiele sind:
-   SRP/CS, die den Stromfluss in elektrischen Hybridsystemen begrenzen, um Isolierungsausfälle und Gefährdungen durch elektrischen Schlag zu verhindern;
-   elektromagnetische Störungen mit SRP/CS;
-   für Brandschutzzwecke gestaltete SRP/CS.
Im Anwendungsbereich dieses Dokuments nicht enthaltene Beispiele sind:
-   Isolierungsausfälle durch Reibung, die zu Gefährdungen durch elektrischen Schlag führen;
-   elektromagnetische Nennstrahlung, die nahe gelegene Maschinensteuerungssysteme beeinflusst;
-   Korrosion, die zu einer Überhitzung von Stromkabeln führt.
Dieses Dokument ist nicht anwendbar für Nicht-E/E/PES-Systeme (z. B. hydraulische, mechanische und pneumatische).
ANMERKUNG 2   Siehe auch ISO 12100 zu Gestaltungsleitsätzen für die Sicherheit von Maschinen.
Dieses Dokument ist nicht anwendbar für sicherheitsbezogene Teile von Steuerungen, die vor dem Veröffentlichungsdatum dieses Dokuments hergestellt wurden.

Tracteurs et matériels agricoles et forestiers - Parties des systèmes de commande relatives à la sécurité - Partie 2: Phase de projet (ISO 25119-2:2019)

Le présent document spécifie la phase de conception du développement des parties relatives à la sécurité des systèmes de commande (SRP/CS) utilisés sur les tracteurs agricoles et forestiers, sur les machines automotrices à conducteur porté et sur les machines portées, semi-portées et traînées utilisées en agriculture. Il peut également s'appliquer aux équipements municipaux mobiles (par exemple machines de nettoiement).
Le présent document ne s'applique pas:
—          aux véhicules aéroportés et sur coussin d'air utilisés en agriculture,
—          aux équipements de jardinage ou horticoles.
Le présent document spécifie les caractéristiques et les catégories requises des SRP/CS pour réaliser leurs fonctions relatives à la sécurité. Il n'identifie pas de niveaux de performance pour des applications spécifiques.
NOTE 1    Les normes spécifiques à une machine donnée (normes de type C) peuvent spécifier des niveaux de performance (AgPL) pour des fonctions relatives à la sécurité dans des machines relevant de leur domaine d'application. Sinon, la spécification de l'AgPL est de la responsabilité du fabricant.
Le présent document s'applique aux parties relatives à la sécurité des systèmes électriques/électroniques/électroniques programmables (E/E/PES), dans la mesure où celles-ci sont liées aux systèmes mécatroniques. Il couvre les éventuels phénomènes dangereux dus au dysfonctionnement de systèmes E/E/PES relatifs à la sécurité, y compris l'interaction entre ces systèmes. Il ne traite pas des phénomènes dangereux associés aux événements suivants: choc électrique, incendie, fumées, chaleur, rayonnement, toxicité, inflammabilité, réactivité, corrosion, libération d'énergie et phénomènes dangereux similaires, à moins qu'ils ne soient causés directement par un dysfonctionnement des systèmes E/E/PES relatifs à la sécurité. Il couvre également le dysfonctionnement des systèmes E/E/PES relatifs à la sécurité qui sont impliqués dans les mesures de protection, protecteurs ou fonctions relatives à la sécurité en réponse aux phénomènes dangereux hors E/E/PES.
Exemples faisant partie du domaine d'application du présent document:
—          SRP/CS limitant le flux de courant dans les hybrides électriques pour empêcher les phénomènes dangereux de panne d'isolement/choc;
—          interférence électromagnétique avec les SRP/CS; et
—          SRP/CS conçues pour empêcher les incendies.
Exemples ne faisant pas partie du domaine d'application:
—          panne d'isolement due au frottement qui engendre des phénomènes de chocs électriques;
—          rayonnement électromagnétique nominal qui impacte les systèmes de commande environnants de la machine;
—          corrosion engendrant une surchauffe des câbles électriques.
Le présent document n'est pas applicable aux systèmes non E/E/PES (par exemple hydraulique, mécanique et pneumatique).
NOTE 2    Pour les principes de conception relatifs à la sécurité des machines, voir également l'ISO 12100.
Le présent document n'est pas applicable aux parties relatives à la sécurité des systèmes de commande fabriqués avant la date de sa publication.

Traktorji ter kmetijski in gozdarski stroji - Varnostni deli krmilnih sistemov - 2. del: Faza koncepta (ISO 25119-2:2019)

Ta dokument določa fazo koncepta za načrtovanje in razvoj varnostnih delov krmilnih sistemov (SRP/CS) za traktorje, ki se uporabljajo v kmetijstvu in gozdarstvu, in za samognane stroje s sedežem ter za priklopne, polpriklopne in vlečene stroje, ki se uporabljajo v kmetijstvu. Uporablja se lahko tudi za mobilno komunalno opremo (kot so pometalni stroji).
Dokument se ne uporablja za:
– letala in vozila z zračno blazino, ki se uporabljajo v kmetijstvu;
– kosilnice ali vrtno opremo.
Ta dokument določa lastnosti in kategorije, ki so zahtevane za sisteme SRP/CS, da lahko ti izvajajo svoje funkcije, povezane z varnostjo. Ne določa ravni zmogljivosti za posebne načine uporabe.
OPOMBA 1: Standardi tipa C, značilni za stroje, lahko določajo ravni zmogljivosti (AgPL) za varnostne funkcije v strojih s svojega področja uporabe. V nasprotnem primeru je specifikacija AgPL odgovornost proizvajalca.
Ta dokument se uporablja za varnostne dele električnih/elektronskih/programirljivih elektronskih sistemov (E/E/PES), saj so ti povezani z mehatronskimi sistemi. Zajema morebitne nevarnosti zaradi motenj v električnih/elektronskih/programirljivih elektronskih varnostnih sistemih, vključno z interakcijo s temi sistemi. Ne obravnava nevarnosti v zvezi z električnim udarom, požarom, dimom, vročino, sevanjem, toksičnostjo, vnetljivostjo, reaktivnostjo, korozijo, sproščanjem energije in podobnih nevarnosti, če jih neposredno ne povzročijo motnje v električnih/elektronskih/programirljivih elektronskih varnostnih sistemih. Obravnava tudi motnje v električnih/elektronskih/programirljivih elektronskih varnostnih sistemih, vključenih v zaščitne ukrepe, varnostne ukrepe ali funkcije, povezane z varnostjo, kot odziv na nevarnosti, ki niso povezane z električnimi/elektronskimi/programirljivimi elektronskimi sistemi.
Med primere znotraj področja uporabe tega dokumenta spadajo:
– omejeni električni tok varnostnih delov krmilnih sistemov (SRP/CS) pri električnih hibridih za preprečevanje okvare izolacije/nevarnosti udara;
– elektromagnetne motnje varnostnih delov krmilnih sistemov;
– varnostni deli krmilnih sistemov, ki so zasnovani za preprečevanje požara.
Primeri, ki ne spadajo na področje uporabe tega dokumenta:
– okvara izolacije zaradi trenja, ki povzroči nevarnost električnega udara;
– nazivno elektromagnetno sevanje, ki vpliva na bližnje krmilne sisteme strojev;
– korozija, ki povzroča pregrevanje električnih kablov.
Ta dokument se ne uporablja za sisteme, ki niso električni/elektronski/programirljivi elektronski sistemi (kot so hidravlični, mehanski ali pnevmatski).
OPOMBA 2: Glej tudi standard ISO 12100 za načela za načrtovanje v zvezi z varnostjo strojev.
Ta dokument se ne uporablja za varnostne dele krmilnih sistemov, izdelane pred datumom njegove objave.

General Information

Status
Published
Publication Date
26-Sep-2023
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
27-Sep-2023
Due Date
30-Dec-2023
Completion Date
27-Sep-2023

Buy Standard

Standard
EN ISO 25119-2:2023
English language
63 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2023
Traktorji ter kmetijski in gozdarski stroji - Varnostni deli krmilnih sistemov - 2. del:
Faza koncepta (ISO 25119-2:2019)
Tractors and machinery for agriculture and forestry - Safety-related parts of control
systems - Part 2: Concept phase (ISO 25119-2:2019)
Traktoren und Maschinen für die Land- und Forstwirtschaft - Sicherheitsbezogene Teile
von Steuerungen - Teil 2: Konzeptphase (ISO 25119-2:2019)
Tracteurs et matériels agricoles et forestiers - Parties des systèmes de commande
relatives à la sécurité - Partie 2: Phase de projet (ISO 25119-2:2019)
Ta slovenski standard je istoveten z: EN ISO 25119-2:2023
ICS:
35.240.99 Uporabniške rešitve IT na IT applications in other fields
drugih področjih
65.060.01 Kmetijski stroji in oprema na Agricultural machines and
splošno equipment in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 25119-2
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2023
EUROPÄISCHE NORM
ICS 35.240.99; 65.060.01
English Version
Tractors and machinery for agriculture and forestry -
Safety-related parts of control systems - Part 2: Concept
phase (ISO 25119-2:2019)
Tracteurs et matériels agricoles et forestiers - Parties Traktoren und Maschinen für die Land- und
des systèmes de commande relatives à la sécurité - Forstwirtschaft - Sicherheitsbezogene Teile von
Partie 2: Phase de projet (ISO 25119-2:2019) Steuerungen - Teil 2: Konzeptphase (ISO 25119-
2:2019)
This European Standard was approved by CEN on 9 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25119-2:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4

European foreword
The text of ISO 25119-2:2019 has been prepared by Technical Committee ISO/TC 23 "Tractors and
machinery for agriculture and forestry” of the International Organization for Standardization (ISO) and
has been taken over as EN ISO 25119-2:2023 by Technical Committee CEN/TC 144 “Tractors and
machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2024, and conflicting national standards shall
be withdrawn at the latest by March 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 25119-2:2019 has been approved by CEN as EN ISO 25119-2:2023 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1— Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
1.1.2. Principles of safety -----

integration
1.1.2(a) 5.3, 6.3, 7.3, A.1, A.2, A.3, A.4,

A.5, A.6, H.2, H.3, H.4, H.5, J1, J2
1.1.2(c) 5.3, 6.3, 7.3, A.1, A.2, A.3, A.4,

A.5, A.6, H.2, H.3, H.4, H.5, J1, J2
1.1.2(d) NOT COVERED
1.1.2(e) NOT COVERED
1.1.3. Materials and products NOT COVERED
1.1.4. Lighting NOT COVERED
1.1.5. Design of machinery to
NOT COVERED
facilitate its handling
1.1.6. Ergonomics NOT COVERED
1.1.7. Operating positions NOT COVERED
1.1.8. Seating NOT COVERED
1.2. CONTROL SYSTEMS -----
1.2.1. Safety and reliability of 5.3, 6.3, 7.3, A.1, A.2, A.3, A.4,

control systems A.5, A.6, H.2, H.3, H.4, H.5, J1, J2
1.2.2. Control devices NOT COVERED
1.2.3. Starting NOT COVERED
1.2.4. Stopping -----
1.2.4.1 Normal Stop NOT COVERED
1.2.4.2. Operational stop NOT COVERED
1.2.4.3. Emergency stop NOT COVERED
1.2.4.4. Assembly of machinery NOT COVERED
1.2.5. Selection of control or
NOT COVERED
operating modes
1.2.6. Failure of the power 6.3, 7.3

supply
1.3. PROTECTION AGAINST ----
MECHANICAL HAZARDS
1.3.1. Risk of loss of stability NOT COVERED
1.3.2. Risk of break-up during
NOT COVERED
operation
1.3.3. Risks due to falling or
NOT COVERED
ejected objects
1.3.4. Risks due to surfaces,
NOT COVERED
edges or angles
1.3.5. Risks related to combined
NOT COVERED
machinery
1.3.6. Risks related to variations
NOT COVERED
in operating conditions
1.3.7. Risks related to moving
NOT COVERED
parts
1.3.8. Choice of protection
against risks arising from NOT COVERED
moving parts
1.3.9. Risks of uncontrolled
NOT COVERED
movements
1.4. REQUIRED ----
CHARACTERISTICS OF GUARDS
AND PROTECTIVE DEVICES
1.4.1. General requirements NOT COVERED
1.4.2. Special requirements for
NOT COVERED
guards
1.4.3. Special requirements for
NOT COVERED
protective devices
1.5. RISKS DUE TO OTHER ----
HAZARDS
1.5.1. Electricity supply NOT COVERED
1.5.2. Static electricity NOT COVERED
1.5.3. Energy supply other than
NOT COVERED
electricity
1.5.4. Errors of fitting NOT COVERED
1.5.5. Extreme temperatures NOT COVERED
1.5.6. Fire NOT COVERED
1.5.7. Explosion NOT COVERED
1.5.8. Noise NOT COVERED
1.5.9. Vibrations NOT COVERED
1.5.10. Radiation NOT COVERED
1.5.11. External radiation NOT COVERED
1.5.12. Laser radiation NOT COVERED
1.5.13. Emissions of hazardous
NOT COVERED
materials and substances
1.5.14. Risk of being trapped in
NOT COVERED
a machine
1.5.15. Risk of slipping, tripping
NOT COVERED
or falling
1.5.16. Lightning NOT COVERED
1.6. MAINTENANCE -----
1.6.1. Machinery maintenance NOT COVERED
1.6.2. Access to operating
NOT COVERED
positions and servicing points
1.6.3. Isolation of energy
NOT COVERED
sources
1.6.4. Operator intervention NOT COVERED
1.6.5. Cleaning of internal parts NOT COVERED
1.7. INFORMATION ----
1.7.1. Information and warnings
NOT COVERED
on the machinery
1.7.1.1. Information and
NOT COVERED
information devices
1.7.1.2. Warning devices NOT COVERED
1.7.2. Warning of residual risks NOT COVERED
1.7.3. Marking of machinery NOT COVERED
1.7.4. Instructions NOT COVERED
2.4. MACHINERY FOR ----
PESTICIDE APPLICATION
2.4.2. General NOT COVERED
2.4.3. Controls and monitoring NOT COVERED
2.4.4. Filling and emptying NOT COVERED
2.4.5. Application of pesticides ----
2.4.5.1. Application rate NOT COVERED
2.4.5.2. Distribution, deposition
NOT COVERED
and drift of pesticide
2.4.5.3. Tests NOT COVERED
2.4.5.4. Losses during stoppage NOT COVERED
2.4.6. Maintenance ----
2.4.6.1. Cleaning NOT COVERED
2.4.6.2. Servicing NOT COVERED
2.4.7. Inspections NOT COVERED
2.4.8. Marking of nozzles,
NOT COVERED
strainers and filters
2.4.9. Indication of pesticide in
NOT COVERED
use
2.4.10. Instructions NOT COVERED
3.2. WORK POSITIONS ---
3.2.1. Driving position NOT COVERED
3.2.2. Seating NOT COVERED
3.2.3. Positions for other
NOT COVERED
persons
3.3. CONTROL SYSTEMS ---
3.3.1. Control devices NOT COVERED
3.3.2. Starting/moving NOT COVERED
3.3.3. Travelling function NOT COVERED
3.3.4. Movement of pedestrian-
NOT COVERED
controlled machinery
3.3.5. Control circuit failure NOT COVERED
3.4. PROTECTION AGAINST ---
MECHANICAL HAZARDS
3.4.1. Uncontrolled movements NOT COVERED
3.4.2. Moving transmission
NOT COVERED
parts
3.4.3. Roll-over and tip-over NOT COVERED
3.4.4. Falling objects NOT COVERED
3.4.5. Means of access NOT COVERED
3.4.6. Towing devices NOT COVERED
3.4.7. Transmission of power
between self-propelled
NOT COVERED
machinery (or tractor) and
recipient machinery
3.5. PROTECTION AGAINST ----
OTHER HAZARDS
3.5.1. Batteries NOT COVERED
3.5.2. Fire NOT COVERED
3.5.3. Emissions of hazardous
NOT COVERED
substances
3.6. INFORMATION AND ----
INDICATIONS
3.6.1. Signs, signals and
NOT COVERED
warnings
3.6.2. Marking NOT COVERED
3.6.3. Instructions ----
3.6.3.1. Vibrations NOT COVERED
3.6.3.2. Multiple uses NOT COVERED

Table ZA.2 — Applicable Standards to confer presumption of conformity as described in this
Annex ZA
Column 1 Column 2 International Column 3 Column 4
Reference in Clause Standard Edition
Title Corresponding
European Standard
Edition
ISO 25119-1:2018 ISO 25119-1:2018 Tractors and machinery EN ISO 25119-1:2023
for agriculture and
ISO 25119- EN ISO 25119-
forestry — Safety-
1:2018/A1:2020 1:2023/A1:2023
related parts of control
systems — Part 1:
General principles for
design and
development
ISO 25119-3:2018 ISO 25119-3:2018 Tractors and machinery
for agriculture and
ISO 25119- EN ISO 25119-3:2023
forestry — Safety-
3:2018/A1:2020
EN ISO 25119-
related parts of control
3:2023/A1:2023
systems — Part 3:
Series development,
hardware and software
ISO 25119-4:2018 ISO 25119-4:2018 Tractors and machinery
for agriculture and
ISO 25119- EN ISO 25119-4:2023
forestry — Safety-
4:2018/A1:2020
EN ISO 25119-
related parts of control
4:2023/A1:2023
systems Part 4:
production, operation,
modification and
supporting processes
The documents listed in the Column 1 of table ZA.2, in whole or in part, are normatively referenced in
this document, i.e. are indispensable for its application. The achievement of the presumption of
conformity is subject to the application of the edition of Standards as listed in Column 4 or, if no
European Standard Edition exists, the International Standard Edition given in  Column 2 of table ZA.2.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 25119-2
Third edition
2019-08
Tractors and machinery for
agriculture and forestry — Safety-
related parts of control systems —
Part 2:
Concept phase
Tracteurs et matériels agricoles et forestiers — Parties des systèmes
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.