EN 50632-2-5:2016/A1:2021

Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular saws

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for circular saws.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-5: Besondere Anforderungen für Kreissägen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-5: Exigences particulières pour les scies circulaires

No scope available

Elektromotorna orodja - Postopek meritve prahu - 2-5. del: Posebne zahteve za krožne žage - Dopolnilo A1

General Information

• Status: Published
• Publication Date: 23-Sep-2021
• ICS: 13.040.40 - Stationary source emissions
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: CLC/TC 116/WG 04 - Dust
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 24-Sep-2021
• Due Date: 09-Aug-2022
• Completion Date: 24-Sep-2021
• Ref Project: SIST EN 50632-2-5:2016/A1:2021 - Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular saws

Relations

• Amends: EN 50632-2-5:2016 - Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular saws
• Effective Date: 08-Sep-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2021
Elektromotorna orodja - Postopek meritve prahu - 2-5. del: Posebne zahteve za
krožne žage - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular
requirements for circular saws
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-5: Besondere
Anforderungen für Kreissägen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-5:
Exigences particulières pour les scies circulaires
Ta slovenski standard je istoveten z: EN 50632-2-5:2016/A1:2021
ICS:
25.100.40 Žagni listi Saws
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-5:2016/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2021
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-5: Particular requirements for circular saws
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-5: Exigences particulières pour les Teil 2-5: Besondere Anforderungen für Kreissägen
scies circulaires
This amendment A1 modifies the European Standard EN 50632-2-5:2016; it was approved by CENELEC on 2021-08-09. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-5:2016/A1:2021 E

Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to 4.3, “Operating conditions” . 4
3 Addition of Figure 101 .
...