ISO/TS 11672:2016
(Main)Connectors for fluid power and general use — Designation and nomenclature
Connectors for fluid power and general use — Designation and nomenclature
ISO/TS 11672:2016 collects the various designation and nomenclature schemes specified in International Standards for connectors and similar products standardized by ISO/TC 131/SC 4. It establishes a uniform nomenclature structure to facilitate standardization of product names used for threaded connectors, push-in connectors, flanges, hose fittings, port plugs and quick-action couplings. The designation and nomenclature established in this document are applicable for procurement purposes when agreed to by user and supplier.
Connecteurs pour transmissions hydrauliques et applications générales — Désignation et nomenclature
General Information
Relations
Buy Standard
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 11672
First edition
Connectors for fluid power and
general use — Designation and
nomenclature
Connecteurs pour transmissions hydrauliques et applications
générales — Désignation et nomenclature
PROOF/ÉPREUVE
Reference number
ISO/TS 11672:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO/TS 11672:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 11672:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation and format . 1
4.1 General . 1
4.2 Connector size . 2
4.2.1 Threaded connectors & cross connectors . 2
4.2.2 Flange connectors . 3
4.3 Designation for ordering parts . 4
Annex A (normative) Index of letter symbols in alphabetical order . 9
Annex B (informative) Application examples .11
Annex C (informative) Correlation of SAE dash sizes to ISO connector, tube and hose sizes .13
Bibliography .14
© ISO 2016 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO/TS 11672:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Pa
...
TECHNICAL ISO/TS
SPECIFICATION 11672
First edition
2016-09-01
Connectors for fluid power and
general use — Designation and
nomenclature
Connecteurs pour transmissions hydrauliques et applications
générales — Désignation et nomenclature
Reference number
ISO/TS 11672:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO/TS 11672:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 11672:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation and format . 1
4.1 General . 1
4.2 Connector size . 2
4.2.1 Threaded connectors and cross connectors . 2
4.2.2 Flange connectors . 3
4.3 Designation for ordering parts . 4
Annex A (normative) Index of letter symbols in alphabetical order . 9
Annex B (informative) Application examples .11
Annex C (informative) Correlation of SAE dash sizes to ISO connector, tube and hose sizes .13
Bibliography .14
© ISO 2016 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 11672:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.