Satellite Earth Stations and Systems (SES) - Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 2: User Equipment (UE) for wideband systems

The present document applies to User Equipment (UE) radio equipment type which has the following characteristics:
• these UEs have both transmit and receive capabilities and operate in an hybrid Satellite/terrestrial network
i.e. a satellite and/or Complementary Ground Component (CGC) network;
• the satellite component is based on GSO;
• these UEs operate with an assigned channel signal bandwidth (CBw) of 1 MHz or greater;
• these UEs may be handset, handheld, portable, vehicle-mounted, aircraft mounted device (in this case the
present document refers to Aeronautical Terminal - AT) host connected, semi-fixed or fixed equipment, or
may be an element in a multi-mode terminal. It may consist of a number of modules with associated
connections and user interface, or may be a self contained single unit;
• if the UE is an element in a multi-mode terminal, unless otherwise stated in the present document, its
requirements apply only to the UE element of the terminal operating in the Mobile Satellite Service (MSS)
frequency bands given in Table 1;
• the present document applies for several class of UEs:
- UE for terrestrial use Power Class 1 - clauses 4 and 5;
- UE for terrestrial use Power Class 1bis - clauses 4 and 5;
- UE for terrestrial use Power Class 2 - clauses 4 and 5;
- UE for terrestrial use Power Class 3 - clauses 4 and 5;
- UE for aeronautical use (Aeronautical Terminal - AT) - clauses 6 and 7;
- UE for terrestrial use (non-aeronautical UE E-UTRA) - clauses 8 and 9;
• the Aeronautical Terminals (AT) operates at altitude of 1 000 m and higher above ground level.
The present document is intended to cover the provisions of Directive 2014/53/EU [9] (RE Directive) article 3.2, which
states that "Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio
spectrum in order to avoid harmful interference".

Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU, za mobilne zemeljske postaje (MES), ki delujejo v frekvenčnih pasovih od 1980 MHz do 2010 MHz (zemlja-vesolje) in od 2170 MHz do 2200 MHz (vesolje-zemlja) - 2. del: Uporabniška oprema za širokopasovne sisteme

Ta dokument se uporablja za radijsko opremo uporabniške opreme (UE) z naslednjimi značilnostmi:
• Uporabniška oprema ima sposobnost oddajanja in sprejemanja ter deluje v hibridnem satelitskem/prizemnem omrežju, tj. satelitskem omrežju in/ali omrežju komplementarne talne komponente (CGC).
• Satelitska komponenta temelji na geostacionarnem satelitu (GSO).
• Komplementarne talne komponente delujejo s pasovno širino signala dodeljenega kanala (CBw), ki je 1 MHz ali večja.
• Komplementarne talne komponente so lahko ročne prenosne naprave, ki so pritrjene ali polpritrjene na vozilo ali montirane v letalu (v tem primeru se ta dokument nanaša na letalski terminal – AT) in povezane z gostiteljem oziroma so lahko sestavni del večnačinovnega terminala. Sestavljene so lahko iz več modulov s povezanimi priključki in uporabniškim vmesnikom ali so samozadostna enota.
• Če je uporabniška oprema sestavni del večnačinovnega terminala,
zahteve tega dokumenta se uporabljajo samo za uporabniško opremo v terminalu, ki deluje v frekvenčnih pasovih mobilnih satelitskih storitev (MSS), podanih v preglednici 1, razen če je v dokumentu navedeno drugače.
• Ta dokument se uporablja za različne razrede uporabniške opreme:
– uporabniška oprema za prizemno uporabo močnostnega razreda 1 – točki 4 in 5;
– uporabniška oprema za prizemno uporabo močnostnega razreda 1bis – točki 4 in 5;
– uporabniška oprema za prizemno uporabo močnostnega razreda 2 – točki 4 in 5;
– uporabniška oprema za prizemno uporabo močnostnega razreda 3 – točki 4 in 5;
– uporabniška oprema za letalsko uporabo (letalski terminal) – točki 6 in 7;
– uporabniška oprema za prizemno uporabo (neletalska uporabniška oprema E-UTRA) – točki 8 in 9.
• Letalski terminali delujejo na višini 1000 m in več nad nivojem tal.
Ta dokument zajema določbe člena 3.2 direktive 2014/53/EU [9] (direktiva RE), ki navaja, da »... mora biti radijska oprema izdelana tako, da optimalno uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja«.

General Information

Status
Published
Publication Date
20-Sep-2016
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Sep-2016
Due Date
17-Nov-2016
Completion Date
21-Sep-2016

Buy Standard

Standard
EN 302 574-2 V2.1.2:2016
English language
103 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ETSI EN 302 574-2 V2.1.2 (2016-09) - Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170 MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: User Equipment (UE) for wideband systems
English language
103 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 302 574-2 V2.1.2:2016
01-november-2016
6DWHOLWVNH]HPHOMVNHSRVWDMHLQVLVWHPL 6(6 +DUPRQL]LUDQLVWDQGDUGNL]DMHPD
ELVWYHQH]DKWHYHþOHQDGLUHNWLYH(8]DPRELOQH]HPHOMVNHSRVWDMH
0(6 NLGHOXMHMRYIUHNYHQþQLKSDVRYLKRG0+]GR0+] ]HPOMD
YHVROMH LQRG0+]GR0+] YHVROMH]HPOMD GHO8SRUDEQLãNDRSUHPD
]DãLURNRSDVRYQHVLVWHPH
Satellite Earth Stations and Systems (SES) - Harmonised Standard for Mobile Earth
Stations (MES) operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and 2 170
MHz to 2 200 MHz (space-to-earth) frequency bands covering the essential requirements
of article 3.2 of the Directive 2014/53/EU - Part 2: User Equipment (UE) for wideband
systems
Ta slovenski standard je istoveten z: ETSI EN 302 574-2 V2.1.2 (2016-09)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
SIST EN 302 574-2 V2.1.2:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 302 574-2 V2.1.2:2016

---------------------- Page: 2 ----------------------

SIST EN 302 574-2 V2.1.2:2016
ETSI EN 302 574-2 V2.1.2 (2016-09)






HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Mobile Earth Stations (MES)
operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and
2 170 MHz to 2 200 MHz (space-to-earth) frequency bands
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 2: User Equipment (UE) for wideband systems

---------------------- Page: 3 ----------------------

SIST EN 302 574-2 V2.1.2:2016
 2 ETSI EN 302 574-2 V2.1.2 (2016-09)



Reference
REN/SES-00414
Keywords
broadband, IMT, mobile, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 302 574-2 V2.1.2:2016
 3 ETSI EN 302 574-2 V2.1.2 (2016-09)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 11
Introduction . 12
1 Scope . 13
2 References . 14
2.1 Normative references . 14
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 16
3.3 Abbreviations . 16
4 Technical requirements specifications for UE . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.1 Introduction. 18
4.2.2 Control and monitoring functions . 18
4.2.2.1 Definition . 18
4.2.2.2 Limit . 18
4.2.2.3 Conformance . 19
4.2.3 Maximum output power . 19
4.2.3.1 Definition . 19
4.2.3.2 Limit . 19
4.2.3.3 Conformance . 19
4.2.4 Spectrum emissions mask . 19
4.2.4.1 Definition . 19
4.2.4.2 Limit . 19
4.2.4.3 Conformance . 20
4.2.5 Transmitter spurious emis sions . 20
4.2.5.1 Definition . 20
4.2.5.2 Limits . 20
4.2.5.3 Conformance . 21
4.2.6 Minimum output power . 21
4.2.6.1 Definition . 21
4.2.6.2 Limits . 21
4.2.6.3 Conformance . 21
4.2.7 Adjacent Channel Leakage Power Ratio (ACLR) . 21
4.2.7.1 Definition . 21
4.2.7.2 Limits . 21
4.2.7.3 Conformance . 22
4.2.8 Out of synchronization handling of output power . 22
4.2.8.1 Definition . 22
4.2.8.2 Limits . 22
4.2.8.3 Conformance . 22
4.2.9 Receiver Adjacent Channel Selectivity (ACS) . 23
4.2.9.1 Definition . 23
4.2.9.2 Limits . 23
4.2.9.3 Conformance . 23
4.2.10 Blocking characteristics . 23
4.2.10.1 Definition . 23
4.2.10.2 Limits . 24
4.2.10.3 Conformance . 24
4.2.11 Receiver spurious response . 24
4.2.11.1 Definition . 24
ETSI

---------------------- Page: 5 ----------------------

SIST EN 302 574-2 V2.1.2:2016
 4 ETSI EN 302 574-2 V2.1.2 (2016-09)
4.2.11.2 Limits . 24
4.2.11.3 Conformance . 24
4.2.12 Receiver intermodulation characteristics . 24
4.2.12.1 Definition . 24
4.2.12.2 Limits . 25
4.2.12.3 Conformance . 25
4.2.13 Receiver spurious emissions . 25
4.2.13.1 Definition . 25
4.2.13.2 Limits . 25
4.2.13.3 Conformance . 26
5 Testing for compliance with technical requirements . 26
5.1 Environmental conditions for testing . 26
5.1.1 Specification of the environmental test conditions . 26
5.1.2 Tests under extreme voltage conditions . 26
5.2 Tests frequencies . 26
5.3 Interpretation of the measurement results . 27
5.4 Radio test suites . 28
5.4.1 Control and monitoring functions . 28
5.4.1.1 Test method . 28
5.4.2 Maximum output power . 29
5.4.2.1 Method of test . 29
5.4.2.1.1 Initial conditions . 29
5.4.2.1.2 Procedure . 29
5.4.2.2 Test requirements . 29
5.4.3 Spectrum emission mask . 29
5.4.3.1 Method of test . 29
5.4.3.1.1 Initial conditions . 29
5.4.3.1.2 Procedure . 29
5.4.3.2 Test requirements . 30
5.4.4 Transmitter spurious emis sions . 30
5.4.4.1 Method of test . 30
5.4.4.1.1 Initial conditions . 30
5.4.4.1.2 Procedure . 30
5.4.4.2 Test requirements . 30
5.4.5 Minimum output power . 30
5.4.5.1 Method of test . 30
5.4.5.1.1 Initial conditions . 30
5.4.5.1.2 Procedure . 30
5.4.5.2 Test requirements . 30
5.4.6 Adjacent Channel Leakage power Ratio (ACLR) . 31
5.4.6.0 General . 31
5.4.6.1 Method of test . 31
5.4.6.1.1 Initial conditions . 31
5.4.6.1.2 Procedure . 31
5.4.6.2 Test requirements . 31
5.4.7 Out of synchronization handling of output power . 31
5.4.7.1 Method of test . 31
5.4.7.1.1 Initial conditions . 31
5.4.7.1.2 Procedure . 31
5.4.7.2 Test requirements . 32
5.4.8 Adjacent Channel Selectivity (ACS) . 32
5.4.8.1 Method of test . 32
5.4.8.1.1 Initial conditions . 32
5.4.8.1.2 Procedure . 32
5.4.8.2 Test requirements . 33
5.4.9 Blocking characteristics . 33
5.4.9.1 Method of test . 33
5.4.9.1.1 Initial requirements . 33
5.4.9.1.2 Procedure . 33
5.4.9.2 Test requirements . 34
5.4.10 Receiver spurious response . 34
ETSI

---------------------- Page: 6 ----------------------

SIST EN 302 574-2 V2.1.2:2016
 5 ETSI EN 302 574-2 V2.1.2 (2016-09)
5.4.10.1 Method of test . 34
5.4.10.1.1 Initial conditions . 34
5.4.10.1.2 Procedure . 34
5.4.10.2 Test requirements . 34
5.4.11 Receiver intermodulation characteristics . 34
5.4.11.1 Method of test . 34
5.4.11.1.1 Initial conditions . 34
5.4.11.1.2 Procedure . 34
5.4.11.2 Test requirements . 35
5.4.12 Receiver spurious emissions . 35
5.4.12.1 Method of test . 35
5.4.12.1.1 Initial conditions . 35
5.4.12.1.2 Procedure . 35
5.4.12.2 Test requirements . 35
6 Technical requirements specifications for the UE mounted on aircraft (Aeronautical Terminals) . 35
6.1 Environmental profile . 35
6.2 Conformance requirements . 35
6.2.0 General . 35
6.2.1 Introduction. 35
6.2.2 Transmitter Maximum output power . 36
6.2.2.1 Definition . 36
6.2.2.2 Limit . 36
6.2.2.3 Conformance . 36
6.2.3 Transmitter Spectrum emissions mask . 36
6.2.3.1 Definition . 36
6.2.3.2 Limit . 37
6.2.3.3 Conformance . 37
6.2.4 Transmitter spurious emis sions . 37
6.2.4.1 Definition . 37
6.2.4.2 Limits . 37
6.2.4.3 Conformance . 38
6.2.5 Transmitter Minimum output power . 38
6.2.5.1 Definition . 38
6.2.5.2 Limits . 38
6.2.5.3 Conformance . 38
6.2.6 Adjacent Channel Leakage Power Ratio (ACLR) . 38
6.2.6.1 Definition . 38
6.2.6.2 Limits . 38
6.2.6.3 Conformance . 39
6.2.7 Receiver Adjacent Channel Selectivity (ACS) . 39
6.2.7.1 Definition . 39
6.2.7.2 Limits . 39
6.2.7.3 Conformance . 40
6.2.8 Blocking characteristics .
...

ETSI EN 302 574-2 V2.1.2 (2016-09)






HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Mobile Earth Stations (MES)
operating in the 1 980 MHz to 2 010 MHz (earth-to-space) and
2 170 MHz to 2 200 MHz (space-to-earth) frequency bands
covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 2: User Equipment (UE) for wideband systems

---------------------- Page: 1 ----------------------
2 ETSI EN 302 574-2 V2.1.2 (2016-09)



Reference
REN/SES-00414
Keywords
broadband, IMT, mobile, satellite
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 302 574-2 V2.1.2 (2016-09)
Contents
Intellectual Property Rights . 11
Foreword . 11
Modal verbs terminology . 11
Introduction . 12
1 Scope . 13
2 References . 14
2.1 Normative references . 14
2.2 Informative references . 14
3 Definitions, symbols and abbreviations . 15
3.1 Definitions . 15
3.2 Symbols . 16
3.3 Abbreviations . 16
4 Technical requirements specifications for UE . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.1 Introduction. 18
4.2.2 Control and monitoring functions . 18
4.2.2.1 Definition . 18
4.2.2.2 Limit . 18
4.2.2.3 Conformance . 19
4.2.3 Maximum output power . 19
4.2.3.1 Definition . 19
4.2.3.2 Limit . 19
4.2.3.3 Conformance . 19
4.2.4 Spectrum emissions mask . 19
4.2.4.1 Definition . 19
4.2.4.2 Limit . 19
4.2.4.3 Conformance . 20
4.2.5 Transmitter spurious emis sions . 20
4.2.5.1 Definition . 20
4.2.5.2 Limits . 20
4.2.5.3 Conformance . 21
4.2.6 Minimum output power . 21
4.2.6.1 Definition . 21
4.2.6.2 Limits . 21
4.2.6.3 Conformance . 21
4.2.7 Adjacent Channel Leakage Power Ratio (ACLR) . 21
4.2.7.1 Definition . 21
4.2.7.2 Limits . 21
4.2.7.3 Conformance . 22
4.2.8 Out of synchronization handling of output power . 22
4.2.8.1 Definition . 22
4.2.8.2 Limits . 22
4.2.8.3 Conformance . 22
4.2.9 Receiver Adjacent Channel Selectivity (ACS) . 23
4.2.9.1 Definition . 23
4.2.9.2 Limits . 23
4.2.9.3 Conformance . 23
4.2.10 Blocking characteristics . 23
4.2.10.1 Definition . 23
4.2.10.2 Limits . 24
4.2.10.3 Conformance . 24
4.2.11 Receiver spurious response . 24
4.2.11.1 Definition . 24
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 302 574-2 V2.1.2 (2016-09)
4.2.11.2 Limits . 24
4.2.11.3 Conformance . 24
4.2.12 Receiver intermodulation characteristics . 24
4.2.12.1 Definition . 24
4.2.12.2 Limits . 25
4.2.12.3 Conformance . 25
4.2.13 Receiver spurious emissions . 25
4.2.13.1 Definition . 25
4.2.13.2 Limits . 25
4.2.13.3 Conformance . 26
5 Testing for compliance with technical requirements . 26
5.1 Environmental conditions for testing . 26
5.1.1 Specification of the environmental test conditions . 26
5.1.2 Tests under extreme voltage conditions . 26
5.2 Tests frequencies . 26
5.3 Interpretation of the measurement results . 27
5.4 Radio test suites . 28
5.4.1 Control and monitoring functions . 28
5.4.1.1 Test method . 28
5.4.2 Maximum output power . 29
5.4.2.1 Method of test . 29
5.4.2.1.1 Initial conditions . 29
5.4.2.1.2 Procedure . 29
5.4.2.2 Test requirements . 29
5.4.3 Spectrum emission mask . 29
5.4.3.1 Method of test . 29
5.4.3.1.1 Initial conditions . 29
5.4.3.1.2 Procedure . 29
5.4.3.2 Test requirements . 30
5.4.4 Transmitter spurious emis sions . 30
5.4.4.1 Method of test . 30
5.4.4.1.1 Initial conditions . 30
5.4.4.1.2 Procedure . 30
5.4.4.2 Test requirements . 30
5.4.5 Minimum output power . 30
5.4.5.1 Method of test . 30
5.4.5.1.1 Initial conditions . 30
5.4.5.1.2 Procedure . 30
5.4.5.2 Test requirements . 30
5.4.6 Adjacent Channel Leakage power Ratio (ACLR) . 31
5.4.6.0 General . 31
5.4.6.1 Method of test . 31
5.4.6.1.1 Initial conditions . 31
5.4.6.1.2 Procedure . 31
5.4.6.2 Test requirements . 31
5.4.7 Out of synchronization handling of output power . 31
5.4.7.1 Method of test . 31
5.4.7.1.1 Initial conditions . 31
5.4.7.1.2 Procedure . 31
5.4.7.2 Test requirements . 32
5.4.8 Adjacent Channel Selectivity (ACS) . 32
5.4.8.1 Method of test . 32
5.4.8.1.1 Initial conditions . 32
5.4.8.1.2 Procedure . 32
5.4.8.2 Test requirements . 33
5.4.9 Blocking characteristics . 33
5.4.9.1 Method of test . 33
5.4.9.1.1 Initial requirements . 33
5.4.9.1.2 Procedure . 33
5.4.9.2 Test requirements . 34
5.4.10 Receiver spurious response . 34
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 302 574-2 V2.1.2 (2016-09)
5.4.10.1 Method of test . 34
5.4.10.1.1 Initial conditions . 34
5.4.10.1.2 Procedure . 34
5.4.10.2 Test requirements . 34
5.4.11 Receiver intermodulation characteristics . 34
5.4.11.1 Method of test . 34
5.4.11.1.1 Initial conditions . 34
5.4.11.1.2 Procedure . 34
5.4.11.2 Test requirements . 35
5.4.12 Receiver spurious emissions . 35
5.4.12.1 Method of test . 35
5.4.12.1.1 Initial conditions . 35
5.4.12.1.2 Procedure . 35
5.4.12.2 Test requirements . 35
6 Technical requirements specifications for the UE mounted on aircraft (Aeronautical Terminals) . 35
6.1 Environmental profile . 35
6.2 Conformance requirements . 35
6.2.0 General . 35
6.2.1 Introduction. 35
6.2.2 Transmitter Maximum output power . 36
6.2.2.1 Definition . 36
6.2.2.2 Limit . 36
6.2.2.3 Conformance . 36
6.2.3 Transmitter Spectrum emissions mask . 36
6.2.3.1 Definition . 36
6.2.3.2 Limit . 37
6.2.3.3 Conformance . 37
6.2.4 Transmitter spurious emis sions . 37
6.2.4.1 Definition . 37
6.2.4.2 Limits . 37
6.2.4.3 Conformance . 38
6.2.5 Transmitter Minimum output power . 38
6.2.5.1 Definition . 38
6.2.5.2 Limits . 38
6.2.5.3 Conformance . 38
6.2.6 Adjacent Channel Leakage Power Ratio (ACLR) . 38
6.2.6.1 Definition . 38
6.2.6.2 Limits . 38
6.2.6.3 Conformance . 39
6.2.7 Receiver Adjacent Channel Selectivity (ACS) . 39
6.2.7.1 Definition . 39
6.2.7.2 Limits . 39
6.2.7.3 Conformance . 40
6.2.8 Blocking characteristics . 40
6.2.8.1 Definition . 40
6.2.8.2 Limits . 40
6.2.8.3 Conformance . 41
6.2.9 Receiver spurious response . 42
6.2.9.1 Definition . 42
6.2.9.2 Limits . 42
6.2.9.3 Conformance . 42
6.2.10 Receiver intermodulation characteristics . 42
6.2.10.1 Definition .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.