SIST EN 302 217-1 V3.1.1:2017
(Main)Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview, common characteristics and system-dependent requirements
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview, common characteristics and system-dependent requirements
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where
frequency co-ordination is generally applied. These requirements are introduced in two different clauses
sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper
system operation and deployment when specific deployment conditions or compatibility requirements are
present. Compliance to all or some of these requirements is left to manufacturer decision.
Technical background for most of the parameters and requirements referred to in this multi-part deliverable may be
found in ETSI TR 101 036-1 [i.16].
Health and safety requirements, relevant to article 3.1a of Directive 2014/53/EU [i.1] are not considered in any part of
this ETSI EN 302 217 series. CENELEC is responsible for the relevant standards.
EMC conditions and requirements, relevant to article 3.1b of Directive 2014/53/EU [i.1] and any other essential
requirement relevant to article 3.3 of Directive 2014/53/EU [i.1] are not in the scope of any part of this ETSI
EN 302 217 series. EMC requirements may be found in ETSI EN 301 489-1 [i.11] and ETSI EN 301 489-4 [i.12].
Fiksni radijski sistemi - Karakteristike in zahteve za opremo in antene tipa točka-točka - 1. del: Pregled, splošne karakteristike in sistemsko odvisne zahteve
Ta dokument se uporablja za digitalne fiksne radijske sisteme (DFRS) za delovanje tipa točka-točka z vgrajenimi in zunanjimi antenami, ki delujejo v frekvenčnem območju od 1 GHz do 86 GHz, ki ustreza ustreznim frekvenčnim pasom od 1,4 GHz do 86 GHz, kot je opisano v dodatkih od B do J standarda ETSI EN 302 217-2 [18].
Ta dokument povzema:
• vse karakteristike, načela ter izraze in definicije ključnega pomena, ki so skupne za vse dele
opreme in antene v sistemih tipa točka-točka ter jih je treba upoštevati pri uporabi vseh ostalih delov skupine standardov ETSI EN 302 217;
• vse sistemsko odvisne karakteristike za opremo tipa točka-točka (P-P), ki se uporablja v pasovih, kjer se običajno uporablja frekvenčna koordinacija. Te zahteve so predstavljene v dveh različnih podtočkah:
– Glavne zahteve so zahteve, ki se nanašajo tudi na »bistvene zahteve« člena 3.2 direktive 2014/53/EU [i.1] in so podrobneje navedene v harmoniziranem standardu ETSI EN 302 217-2 [18].
– Dopolnilne zahteve so zahteve, ki se ne nanašajo na bistvene zahteve člena 3.2 direktive 2014/53/EU [i.1]. Kljub temu so bile skupaj dogovorjene za pravilno delovanje in uvajanje sistema v primeru obstoja posebnih pogojev uvajanja ali zahtev združljivosti. Skladnost z eno ali več zahtevami je prepuščena proizvajalčevi odločitvi.
Tehnično ozadje za večino parametrov in zahtev v tem večdelnem dokumentu je mogoče najti v standardu ETSI TR 101 036-1 [i.16].
Zdravstvene in varnostne zahteve v zvezi s členom 3.1a direktive 2014/53/EU [i.1] niso obravnavane v nobenem delu te skupine standardov ETSI EN 302 217. CENELEC je odgovoren za ustrezne standarde.
Pogoji in zahteve glede elektromagnetne združljivosti (EMC) v zvezi s členom 3.1b direktive 2014/53/EU [i.1] ter morebitne druge bistvene zahteve v zvezi s členom 3.3 direktive 2014/53/EU [i.1] niso obravnavani v nobenem delu te skupine standardov ETSI EN 302 217. Zahteve glede elektromagnetne združljivosti so na voljo v standardih ETSI EN 301 489-1 [i.11] in ETSI EN 301 489-4 [i.12].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 1: Overview, common characteristics and system-dependent requirements33.120.40AnteneAerials33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:ETSI EN 302 217-1 V3.1.1 (2017-05)SIST EN 302 217-1 V3.1.1:2017en01-julij-2017SIST EN 302 217-1 V3.1.1:2017SLOVENSKI
STANDARD
SIST EN 302 217-1 V3.1.1:2017
ETSI EN 302 217-1 V3.1.1 (2017-05) Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 1: Overview, common characteristics and system-independent requirements
EUROPEAN STANDARD SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 2
Reference REN/ATTM-04028 Keywords antenna, DFRS, DRRS, FWA, point-to-point, radio, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 12 3.1 Definitions . 12 3.2 Symbols . 17 3.3 Abbreviations . 18 4 Structure and applicability of the ETSI EN 302 217 series . 20 4.1 Generality . 20 4.2 Cross references to previously relevant ENs and TSs . 21 4.3 Summary of system options provided . 22 4.4 User's guide . 25 5 General characteristics . 27 5.1 Frequency bands and channel arrangements . 27 5.2 Special compatibility requirements between systems . 27 5.3 Transmission capacity and spectral efficiency . 27 5.4 Performance and availability requirements . 28 5.5 Environmental profiles . 28 5.5.0 Introduction. 28 5.5.1 Environmental profile declared under Directive 2014/53/EU . 28 5.5.2 ETSI environmental profiles . 28 5.5.2.0 Generality . 28 5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations (indoor locations) . 29 5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected locations (outdoor locations) . 29 5.5.3 Test environment profiles . 29 5.6 Power supply . 29 5.6.0 Introduction. 29 5.6.1 Power supply profile declared under Directive 2014/53/EU . 30 5.6.2 ETSI power supply profile . 30 5.7 System block diagram . 30 6 Baseband interfaces and parameters . 31 6.0 Introduction . 31 6.1 Ethernet interfaces . 31 6.2 Plesiochronous interfaces . 31 6.3 Synchronous digital hierarchy interfaces . 31 6.4 Other baseband data interfaces . 31 7 Main requirements . 32 7.0 Introduction . 32 7.1 General requirements . 32 7.1.1 System identification . 32 7.1.2 System nominal loading . 32 7.1.3 Environmental profile . 32 7.2 Transmitter characteristics. 33 7.2.1 Transmitter power and power tolerance . 33 7.2.1.1 Maximum power and EIRP . 33 7.2.1.2 Combined TX power and EIRP limits . 33 SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 4 7.2.1.3 Output power tolerance . 33 7.2.2 Transmitter power and frequency control . 34 7.2.2.1 Transmitter power control (ATPC and RTPC) . 34 7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34 7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 34 7.2.2.2 Remote Frequency Control (RFC) . 35 7.2.3 Radio Frequency (RF) spectrum mask. 35 7.2.4 Discrete CW components exceeding the spectrum mask limit . 35 7.2.4.1 Discrete CW components at the symbol rate . 35 7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35 7.2.5 Unwanted emissions in the spurious domain - external . 35 7.2.6 Dynamic change of modulation order . 35 7.2.7 Radio frequency tolerance . 35 7.2.8 Emission limitations outside the allocated band . 35 7.3 Receiver characteristics . 36 7.3.1 Unwanted emissions in the spurious domain - external . 36 7.3.2 BER as a function of receiver signal level . 36 7.3.3 Receiver selectivity . 36 7.3.3.1 Introduction . 36 7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36 7.3.3.3 CW spurious interference (blocking and spurious response) . 36 7.4 Antenna characteristics . 36 8 Complementary requirements . 37 8.0 Introduction . 37 8.1 Branching/feeder requirements . 37 8.1.1 Waveguide flanges (or other connectors) . 37 8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38 8.2 Intermodulation products . 38 8.3 Transmitter characteristics. 39 8.3.1 Unwanted emissions - internal . 39 8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39 8.4 Receiver characteristics . 40 8.4.1 Maximum input level and input level range . 40 8.4.2 Unwanted emissions - internal . 41 8.4.3 Image rejection . 41 8.4.4 Innermost channel selectivity . 42 8.5 System performance without diversity . 42 8.5.1 Equipment Residual BER (RBER) . 42 8.5.2 Distortion sensitivity . 44 8.5.2.1 Introduction . 44 8.5.2.2 Requirement . 44 8.5.2.3 Assessment . 45 8.5.3 Interference sensitivity for CCDP with XPIC operation . 46 8.5.3.1 General . 46 8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46 8.6 System characteristics with diversity . 46 8.6.0 Introduction. 46 8.6.1 Differential delay compensation . 46 8.6.2 BER performance . 46 Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer compatibility is required . 47 A.0 Introduction . 47 A.1 TX masks assessment . 48 A.2 Normal channels - Emission mask floor . 48 A.2.1 RBER impact . 48 A.2.2 Local TX to RX compatibility . 48 A.2.2.1 Spectrum mask . 48 A.2.2.2 Receiver selectivity . 49 SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 5 A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel separation of 28 MHz to 30 MHz . 49 A.3.0 Introduction . 49 A.3.1 Innermost channels spectrum masks . 49 A.3.2 Receiver innermost channel selectivity . 51 A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel separation of 40 MHz . 52 A.4.0 Introduction . 52 A.4.1 Innermost channels spectrum masks . 52 A.4.2 Receiver innermost channels selectivity . 53 A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54 A.5.0 Introduction . 54 A.5.1 Innermost channels spectrum masks . 54 A.5.2 Receiver innermost channels selectivity . 55 Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and other signals on the traffic interface. 57 Annex C (informative): Information on Multi-channel and Channel-aggregation differences and operation . 58 Annex D (informative): Additional information on relevant characteristics and operation . 60 D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60 D.2 Measurement test set for XPI characteristics . 61 D.3 Differential delay compensation range . 62 D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63 D.4.1 FER/BER equivalence . 63 D.4.2 FER equipment settings and measurement techniques (example) . 64 D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation on spectrum mask and link design requirements . 64 D.5.0 Introduction . 64 D.5.1 ATPC and RTPC . 64 D.5.1.1 ATPC . 64 D.5.1.2 ATPC and RTPC implementation background . 65 D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67 D.5.2.1 Mixed−mode basic concepts . 67 D.5.2.2 Bandwidth adaptive . 68 D.5.2.2.1 Basic concepts . 68 D.5.2.2.2 Bandwidth (channel) occupancy . 68 D.5.3 Impact on frequency co ordination . 68 D.5.4 Impact of operating conditions on "essential" parameters in article 3.2 of Directive 2014/53/EU . 68 D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69 Annex E (informative): Mechanical characteristics . 70 Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 71 Annex G (informative): Change history . 72 History . 73
SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas, as identified below (see note): Part 1: "Overview, common characteristics and system-independent requirements"; Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU"; Part 4: "Antennas". NOTE: In previous regulatory regime of harmonised standards under Directive 1999/5/EC more parts were published, which have been superseded since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC; they are: Part 2-1: which technical content merged in the present document (Part 1); Part 2-2: which technical content is merged in Part 2; Part 3: which technical content is merged in Part 2 (with addition of a complete set of receiver
parameters); Part 4-1: which technical content is merged in Part 4; Part 4-2: which technical content is merged in Part 4.
National transposition dates Date of adoption of this EN: 27 March 2017 Date of latest announcement of this EN (doa): 30 June 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2017 Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 302 217-1 V3.1.1:2017
ETSI ETSI EN 302 217-1 V3.1.1 (2017-05) 7 1 Scope The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands 1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J. The present document summarizes: • all characteristics, principles and, of utmost importance, terms and definitions that are common to all P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217 series; • all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where frequency co-ordination is generally applied. These requirements are introduced in two different clauses sub-sets: - Main requirements are requirements that are also related to the "essential requirements" under article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI EN 302 217-2 [18]. - Complementary requirements are requirements that are not related to essential requirements under article 3.2 of Directive 2014/53
...
ETSI EN 302 217-1 V3.1.1 (2017-05)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 1 ----------------------
2 ETSI EN 302 217-1 V3.1.1 (2017-05)
Reference
REN/ATTM-04028
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 217-1 V3.1.1 (2017-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 17
3.3 Abbreviations . 18
4 Structure and applicability of the ETSI EN 302 217 series . 20
4.1 Generality . 20
4.2 Cross references to previously relevant ENs and TSs . 21
4.3 Summary of system options provided . 22
4.4 User's guide . 25
5 General characteristics . 27
5.1 Frequency bands and channel arrangements . 27
5.2 Special compatibility requirements between systems . 27
5.3 Transmission capacity and spectral efficiency . 27
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 28
5.5.0 Introduction. 28
5.5.1 Environmental profile declared under Directive 2014/53/EU . 28
5.5.2 ETSI environmental profiles . 28
5.5.2.0 Generality . 28
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 29
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 29
5.5.3 Test environment profiles . 29
5.6 Power supply . 29
5.6.0 Introduction. 29
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 30
5.7 System block diagram . 30
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 31
6.2 Plesiochronous interfaces . 31
6.3 Synchronous digital hierarchy interfaces . 31
6.4 Other baseband data interfaces . 31
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 32
7.1.1 System identification . 32
7.1.2 System nominal loading . 32
7.1.3 Environmental profile . 32
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 33
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 217-1 V3.1.1 (2017-05)
7.2.1.3 Output power tolerance . 33
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 34
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 35
7.2.6 Dynamic change of modulation order . 35
7.2.7 Radio frequency tolerance . 35
7.2.8 Emission limitations outside the allocated band . 35
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 36
7.4 Antenna characteristic s . 36
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 38
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 217-1 V3.1.1 (2017-05)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on "essential" parameters in article 3.2 of Directive 2014/53/EU . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 71
Annex G (informative): Change history . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 217-1 V3.1.1 (2017-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and
Multiplexing (ATTM).
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard covering the
essential requirements of article 3.2 of Directive 2014/53/EU";
Part 4: "Antennas".
NOTE: In previous regulatory regime of harmonised standards under Directive 1999/5/EC more parts were
published, which have been superseded since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC;
they are:
Part 2-1: which technical content merged in the present document (Part 1);
Part 2-2: which technical content is merged in Part 2;
Part 3: which technical content is merged in Part 2 (with addition of a complete set of receiver
parameters);
Part 4-1: which technical content is merged in Part 4;
Part 4-2: which technical content is merged in Part 4.
National transposition dates
Date of adoption of this EN: 27 March 2017
Date of latest announcement of this EN (doa): 30 June 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2017
Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 217-1 V3.1.1 (2017-05)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where
frequency co-ordination is generally applied. These requirements are introduced in two different clauses
sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper
system operation and deployment when specific deployment conditions or compatibility requirements are
present
...
Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-independent requirements
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
Reference
REN/ATTM-04028
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 17
3.3 Abbreviations . 18
4 Structure and applicability of the ETSI EN 302 217 series . 20
4.1 Generality . 20
4.2 Cross references to previously relevant ENs and TSs . 21
4.3 Summary of system options provided . 22
4.4 User's guide . 25
5 General characteristics . 27
5.1 Frequency bands and channel arrangements . 27
5.2 Special compatibility requirements between systems . 27
5.3 Transmission capacity and spectral efficiency . 27
5.4 Performance and availability requirements . 28
5.5 Environmental profiles . 28
5.5.0 Introduction. 28
5.5.1 Environmental profile declared under Directive 2014/53/EU . 28
5.5.2 ETSI environmental profiles . 28
5.5.2.0 Generality . 28
5.5.2.1 Equipment intended for telecommunications applications installed in weather-protected locations
(indoor locations) . 29
5.5.2.2 Equipment intended for telecommunications applications installed in not-weather-protected
locations (outdoor locations) . 29
5.5.3 Test environment profiles . 29
5.6 Power supply . 29
5.6.0 Introduction. 29
5.6.1 Power supply profile declared under Directive 2014/53/EU . 30
5.6.2 ETSI power supply profile . 30
5.7 System block diagram . 30
6 Baseband interfaces and parameters . 31
6.0 Introduction . 31
6.1 Ethernet interfaces . 31
6.2 Plesiochronous interfaces . 31
6.3 Synchronous digital hierarchy interfaces . 31
6.4 Other baseband data interfaces . 31
7 Main requirements . 32
7.0 Introduction . 32
7.1 General requirements . 32
7.1.1 System identification . 32
7.1.2 System nominal loading . 32
7.1.3 Environmental profile . 32
7.2 Transmitter characteristics. 33
7.2.1 Transmitter power and power tolerance . 33
7.2.1.1 Maximum power and EIRP . 33
7.2.1.2 Combined TX power and EIRP limits . 33
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
7.2.1.3 Output power tolerance . 33
7.2.2 Transmitter power and frequency control . 34
7.2.2.1 Transmitter power control (ATPC and RTPC) . 34
7.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 34
7.2.2.1.2 Remote Transmitter Power Control (RTPC) . 34
7.2.2.2 Remote Frequency Control (RFC) . 35
7.2.3 Radio Frequency (RF) spectrum mask. 35
7.2.4 Discrete CW components exceeding the spectrum mask limit . 35
7.2.4.1 Discrete CW components at the symbol rate . 35
7.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 35
7.2.5 Unwanted emissions in the spurious domain - external . 35
7.2.6 Dynamic change of modulation order . 35
7.2.7 Radio frequency tolerance . 35
7.2.8 Emission limitations outside the allocated band . 35
7.3 Receiver characteristics . 36
7.3.1 Unwanted emissions in the spurious domain - external . 36
7.3.2 BER as a function of receiver signal level . 36
7.3.3 Receiver selectivity . 36
7.3.3.1 Introduction . 36
7.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 36
7.3.3.3 CW spurious interference (blocking and spurious response) . 36
7.4 Antenna characteristic s . 36
8 Complementary requirements . 37
8.0 Introduction . 37
8.1 Branching/feeder requirements . 37
8.1.1 Waveguide flanges (or other connectors) . 37
8.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 38
8.2 Intermodulation products . 38
8.3 Transmitter characteristics. 39
8.3.1 Unwanted emissions - internal . 39
8.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 39
8.4 Receiver characteristics . 40
8.4.1 Maximum input level and input level range . 40
8.4.2 Unwanted emissions - internal . 41
8.4.3 Image rejection . 41
8.4.4 Innermost channel selectivity . 42
8.5 System performance without diversity . 42
8.5.1 Equipment Residual BER (RBER) . 42
8.5.2 Distortion sensitivity . 44
8.5.2.1 Introduction . 44
8.5.2.2 Requirement . 44
8.5.2.3 Assessment . 45
8.5.3 Interference sensitivity for CCDP with XPIC operation . 46
8.5.3.1 General . 46
8.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 46
8.6 System characteristics with diversity . 46
8.6.0 Introduction. 46
8.6.1 Differential delay compensation . 46
8.6.2 BER performance . 46
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 47
A.0 Introduction . 47
A.1 TX masks assessment . 48
A.2 Normal channels - Emission mask floor . 48
A.2.1 RBER impact . 48
A.2.2 Local TX to RX compatibility . 48
A.2.2.1 Spectrum mask . 48
A.2.2.2 Receiver selectivity . 49
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 49
A.3.0 Introduction . 49
A.3.1 Innermost channels spectrum masks . 49
A.3.2 Receiver innermost channel selectivity . 51
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 52
A.4.0 Introduction . 52
A.4.1 Innermost channels spectrum masks . 52
A.4.2 Receiver innermost channels selectivity . 53
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 54
A.5.0 Introduction . 54
A.5.1 Innermost channels spectrum masks . 54
A.5.2 Receiver innermost channels selectivity . 55
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and
other signals on the traffic interface. 57
Annex C (informative): Information on Multi-channel and Channel-aggregation differences
and operation . 58
Annex D (informative): Additional information on relevant characteristics and operation . 60
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 60
D.2 Measurement test set for XPI characteristics . 61
D.3 Differential delay compensation range . 62
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 63
D.4.1 FER/BER equivalence . 63
D.4.2 FER equipment settings and measurement techniques (example) . 64
D.5 Impact of power control (ATPC and/or RTPC), mixed-mode and bandwidth adaptive operation
on spectrum mask and link design requirements . 64
D.5.0 Introduction . 64
D.5.1 ATPC and RTPC . 64
D.5.1.1 ATPC . 64
D.5.1.2 ATPC and RTPC implementation background . 65
D.5.2 Mixed−mode and bandwidth adaptive operation impact . 67
D.5.2.1 Mixed−mode basic concepts . 67
D.5.2.2 Bandwidth adaptive . 68
D.5.2.2.1 Basic concepts . 68
D.5.2.2.2 Bandwidth (channel) occupancy . 68
D.5.3 Impact on frequency co ordination . 68
D.5.4 Impact of operating conditions on "essential" parameters in article 3.2 of Directive 2014/53/EU . 68
D.6 Typical interference sensitivity behaviour for frequency planning purpose . 69
Annex E (informative): Mechanical characteristics . 70
Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 71
Annex G (informative): Change History . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals,
Transmission and Multiplexing (ATTM), and is now submitted for the Vote phase of the ETSI standards EN Approval
Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-independent requirements";
Part 2: "Digital systems operating in frequency bands from 1 GHz to 86 GHz; Harmonised Standard covering the
essential requirements of article 3.2 of Directive 2014/53/EU";
Part 4: "Antennas".
NOTE: In previous regulatory regime of harmonised standards under Directive 1999/5/EC more parts were
published, which have been superseded since Directive 2014/53/EU [i.1] repealed Directive 1999/5/EC;
they are:
Part 2-1: which technical content merged in the present document (Part 1);
Part 2-2: which technical content is merged in Part 2;
Part 3: which technical content is merged in Part 2 (with addition of a complete set of receiver
parameters);
Part 4-1: which technical content is merged in Part 4;
Part 4-2: which technical content is merged in Part 4.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 302 217-1 V3.1.0 (2017-01)
1 Scope
The present document applies to Digital Fixed Radio Systems (DFRS) in point-to-point operation with integral and
external antennas in the frequency range of 1 GHz to 86 GHz corresponding to the appropriate frequency bands
1,4 GHz to 86 GHz as described in ETSI EN 302 217-2 [18], annex B to annex J.
The present document summarizes:
• all characteristics, principles and, of utmost importance, terms and definitions that are common to all
P-P equipment and antennas and its consultation is necessary when using all other parts of ETSI EN 302 217
series;
• all system-dependent requirements for Point-to-Point (P-P) equipment in applications deployed in bands where
frequency co-ordination is generally applied. These requirements are introduced in two different clauses
sub-sets:
- Main requirements are requirements that are also related to the "essential requirements" under
article 3.2 of Directive 2014/53/EU [i.1] and further detailed in the Harmonised Standard ETSI
EN 302 217-2 [18].
- Complementary requirements are requirements that are not related to essential requirements under
article 3.2 of Directive 2014/53/EU [i.
...
Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 1: Overview, common characteristics and
system-dependent requirements
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
Reference
REN/ATTM-04028
Keywords
antenna, DFRS, DRRS, FWA, point-to-point,
radio, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 14
2 References . 15
2.1 Normative references . 15
2.2 Informative references . 17
3 Definitions, symbols and abbreviations . 19
3.1 Definitions . 19
3.2 Symbols . 25
3.3 Abbreviations . 25
4 General characteristics . 28
4.1 Frequency bands and channel arrangements . 28
4.2 Special compatibility requirements between systems . 28
4.3 Transmission capacity and spectral efficiency . 28
4.4 Performance and availability requirements . 28
4.5 Environmental profiles . 29
4.5.0 Introduction. 29
4.5.1 Environmental profile declared under Directive 2014/53/EU . 29
4.5.2 ETSI environmental profiles . 29
4.5.2.0 Generality . 29
4.5.2.1 Equipment within weather-protected locations (indoor locations) . 30
4.5.2.2 Equipment for not-weather-protected locations (outdoor locations) . 30
4.5.3 Test environment profiles . 30
4.6 Power supply . 30
4.6.0 Introduction. 30
4.6.1 Power supply profile declared under Directive 2014/53/EU . 30
4.6.2 ETSI power supply profile . 31
4.7 System block diagram . 31
5 Baseband interfaces and parameters . 31
5.0 Introduction . 31
5.1 Ethernet interfaces . 32
5.2 Plesiochronous interfaces . 32
5.3 Synchronous digital hierarchy interfaces . 32
5.4 Other baseband data interfaces . 32
6 Main requirements . 33
6.0 Introduction . 33
6.1 General requirements . 33
6.1.1 System identification . 33
6.1.2 System nominal loading . 33
6.1.3 Environmental profile . 33
6.2 Transmitter characteristics. 34
6.2.1 Transmitter power and power tolerance . 34
6.2.1.1 Maximum power and EIRP . 34
6.2.1.2 Combined TX power and EIRP limits . 34
6.2.1.3 Output power tolerance . 34
6.2.2 Transmitter power and frequency control . 35
6.2.2.1 Transmitter power control (ATPC and RTPC) . 35
6.2.2.1.1 Automatic Transmitter Power Control (ATPC) . 35
6.2.2.1.2 Remote Transmitter Power Control (RTPC) . 35
6.2.2.2 Remote Frequency Control (RFC) . 36
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
6.2.3 Radio Frequency (RF) spectrum mask. 36
6.2.4 Discrete CW components exceeding the spectrum mask limit . 36
6.2.4.1 Discrete CW components at the symbol rate . 36
6.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 36
6.2.5 Unwanted emissions in the spurious domain - external . 36
6.2.6 Dynamic change of modulation order . 36
6.2.7 Radio frequency tolerance . 36
6.2.8 Emission limitations outside the allocated band . 36
6.3 Receiver characteristics . 37
6.3.1 Unwanted emissions in the spurious domain - external . 37
6.3.2 BER as a function of receiver signal level . 37
6.3.3 Receiver selectivity . 37
6.3.3.1 Introduction . 37
6.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 37
6.3.3.3 CW spurious interference (blocking and spurious response) . 37
6.4 Antenna characteristic s . 37
7 Complementary requirements . 38
7.0 Introduction . 38
7.1 Branching/feeder requirements . 38
7.1.1 Waveguide flanges (or other connectors) . 38
7.1.2 Return loss of feeder/antenna systems at equipment antenna port (C/C' reference point) . 39
7.2 Intermodulation products . 39
7.3 Transmitter characteristics. 40
7.3.1 Unwanted emissions - internal . 40
7.3.2 Radio Frequency (RF) spectrum mask when mixed manufacturer compatibility is required . 40
7.4 Receiver characteristics . 41
7.4.1 Maximum input level and input level range . 41
7.4.2 Spurious emissions - internal . 42
7.4.3 Image rejection . 42
7.4.4 Innermost channel selectivity . 43
7.5 System performance without diversity . 43
7.5.1 Equipment Residual BER (RBER) . 43
7.5.2 Distortion sensitivity . 45
7.5.2.1 Introduction . 45
7.5.2.2 Requirement . 45
7.5.2.3 Assessment . 46
7.5.3 Interference sensitivity for CCDP with XPIC operation . 47
7.5.3.1 General . 47
7.5.3.2 Co-channel "internal" interference sensitivity in flat fading conditions . 47
7.6 System characteristics with diversity . 47
7.6.0 Introduction. 47
7.6.1 Differential delay compensation . 47
7.6.2 BER performance . 47
Annex A (normative): Spectrum masks and receiver selectivity when mixed manufacturer
compatibility is required . 48
A.0 Introduction . 48
A.1 TX masks assessment . 49
A.2 Normal channels - Emission mask floor . 49
A.2.1 RBER impact . 49
A.2.2 Local TX to RX compatibility . 49
A.2.2.1 Spectrum mask . 49
A.2.2.2 Receiver selectivity . 50
A.3 Innermost channels for channel arrangements from about 4 GHz to about 8,5 GHz with channel
separation of 28 MHz to 30 MHz . 50
A.3.0 Introduction . 50
A.3.1 Innermost channels spectrum masks . 50
A.3.2 Receiver innermost channel selectivity . 52
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
A.4 Innermost channels for channel arrangements from about 4 GHz to 11 GHz with channel
separation of 40 MHz . 53
A.4.0 Introduction . 53
A.4.1 Innermost channels spectrum masks . 53
A.4.2 Receiver innermost channels selectivity . 54
A.5 Innermost channels for 18 GHz channel arrangements with channel separation of 55 MHz . 55
A.5.0 Introduction . 55
A.5.1 Innermost channels spectrum masks . 55
A.5.2 Receiver innermost channels selectivity . 56
Annex B (normative): Definition of equivalent data rates for packet data, PDH/SDH and other
signals on the traffic interface . 58
Annex C (informative): Information on Multi-channel and Channel-aggregation differences and
operation . 59
Annex D (informative): Additional information . 61
D.1 Residual Bit Error Ratio (RBER) and Residual Frame Error Ratio (RFER) . 61
D.2 Measurement test set for XPI characteristics . 62
D.3 Differential delay compensation range . 63
D.4 FER/BER equivalence and FER performance measurement equipment settings (example) . 64
D.4.1 FER/BER equivalence . 64
D.4.2 FER equipment settings and measurement techniques (example) . 65
D.5 Automatic Transmitter Power Control (ATPC) . 65
Annex E (informative): Mechanical characteristics . 67
Annex F (informative): Mitigation techniques referred in ERC/DEC(00)07 (18 GHz band) . 68
Annex G (informative): Notification of interfaces under article 8 of Directive 2014/53/EU . 69
G.0 Introduction . 69
G.1 Applicability of TCAM-RIS model of radio interface specifications to Fixed Service . 69
G.2 Proposed list of radio interface specifications for Fixed Service . 70
Annex H (informative): Change History . 71
Annex I (informative): Bibliography . 72
History . 73
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the Fixed Radio Systems; Characteristics and
requirements for point-to-point equipment and antennas, as identified below (see note):
Part 1: "Overview, common characteristics and system-dependent requirements";
Part 2: "Digital systems operating in frequency bands from about 1,3 GHz to 86 GHz; Harmonized Standard
covering the essential requirements of article 3.2 of Directive 2014/53/EU";
Part 4: "Antennas".
NOTE: In previous regulatory regime of harmonised standards under Directive 1999/5/EC more parts were
published, which have been superseded since Directive 2014/53/EU repealed Directive 1999/5/EC; they
are:
Part 2-1: which technical content merged in the present document (Part 1)
Part 2-2: which technical content is merged in Part 2
Part 3: which technical content is merged in Part 2 (with addition of a complete set of receiver
parameters)
Part 4-1: which technical content is merged in Part 4
Part 4-2: which technical content is merged in Part 4
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 217-1 V3.0.5 (2016-06)
Introduction
(i) Generality and historical background
Digital Fixed Radio Systems (DFRS), used in European countries, had been historically specified in a relatively large
number of specific European Norms produced by ETSI.
Those previous documents, already superseded by first publication of this ETSI EN 302 217 series, contained both
essential requirements and other requirements that, even if not considered essential under Directive 2014/53/EU [i.1] of
16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC, may still be applicable.
For the correct understanding and application of the requirements in the whole ETSI EN 302 217 multipart series, the
definitions summarized in clause 3.1 of the present document are also relevant; those definitions are generally hereby
identified with the use of italic characters (e.g. mixed-mode).
Standards for point-to-point systems, including antennas, cover a very large range of traffic capacities, channel
separations (CS), modulation formats and applications over a very wide range of frequency bands that are summarized
in table 1.
Table 1: Digital Fixed Radio Systems (DFRS) parameters
Parameter Range
Frequency bands from 1 GHz to 86 GHz (see note)
Traffic capacities from 9,6 kbit/s to 622 Mbit/s and to Gbit/s and above in the highest bands
Channel separations from 25 kHz to 112 MHz and to GHz and above in the highest bands
Modulation formats from 2 states to 2 048 states (amplitude and/or phase and/or frequency
modulated states)
Typical applications POINT-TO-POINT (P-P) CONNECTIONS:
rural and urban low/medium/high capacity links for mobile access
infrastructure (backhaul), transport/trunk (long haul), FWA/BWA/ access, fixed
LAN extensions (FLANE) governmental (non-military) links, private fixed
networks, SAP/SAB P-P audio and video links with integral or dedicated
antenna.
STAND ALONE ANTENNAS:
for all of the above applications when integral or dedicated antennas are not
employed
NOTE: Market demand will likely extend the upper limits.
The regulatory framework for placing radio systems on the market, established by Directive 2014/53/EU [i.1] also
requires the availability of Harmonised Standards covering the essential requirements under article 3.2 of Directive
2014/53/EU [i.1]. ETSI EN 302 217 series meet this demand by providing a rational subdivision of technical
characteristics into:
• general system independent parameters, defined in the present document;
• system dependent "main" parameters relevant to the "essential" requirements of art 3.2 of Directive
2014/53/EU [i.1], briefly summarized in the present document but specifically defined in ETSI
EN 302 217-2 [18];
• system dependent "complementary" parameters NOT relevant to the "essential" requirements of art 3.2 of
Directive 2014/53/EU [i.1]. Nevertheless they have been commonly agreed for proper system operation and
deployment when specific deployment conditions or compatibility requirements are present; they are also
defined in the present document.
ETSI EN 302 217-4 [19] includes electrical and mechanical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.