Acoustics - Methods for the description and physical measurement of single impulses or series of impulses - Corrigendum (ISO 10843:1997/Cor 1:2009)

This International Standard describes preferred methods for the description and the physical measurement of single impulsive sounds or short series of impulsive sounds and for the presentation of the data. It does not provide methods for interpreting the potential effects of series of impulses of noise on hearing, community response or structures. This International Standard applies to single impulsive sounds or short series of impulsive sounds such as those produced by explosions, artillery fire, bombing and similar activities, sonic booms, pistol and rifle fire, and cartridgeoperated tools or machines. Two different kinds of measurements are considered:
a) measurements of phase-sensitive parameters, such as peak sound pressure level and duration, that directly characterize the variation of sound pressure with time; and
b) measurements of time-integrated quantities such as frequency-weighted sound exposure level or sound energy level.

Acoustique — Métrique et techniques pour le mesurage physique de bruits impulsionnels isolés ou en courtes rafales — Rectificatif technique 1

Akustika - Metode za opis in fizikalne meritve posameznih ali zaporednih impulzov - Popravek (ISO 10843:1997/Cor 1:2009)

Ta mednarodni standard opisuje prednostne metode za opis in fizikalne meritve posameznega impulznega hrupa ali kratkega zaporednega impulznega hrupa ter za predstavitev podatkov. Ne določa metod za razlago morebitnih vplivov zaporednih impulzov hrupa na sluh, odziv skupnosti ali strukture.
Ta mednarodni standard se uporablja za posamezni impulzni hrup ali kratek zaporedni impulzni hrup, kot je hrup, ki ga povzročijo eksplozije, topniško orožje, bombardiranje in podobne dejavnosti, hrup pri prebitju zvočnega zidu, streljanje s pištolami in puškami ter orodja ali stroji z nabojnim delovanjem.
Obravnavani sta dve različni vrsti meritev:
a) meritve fazno občutljivih parametrov, kot sta vršna raven zvočnega tlaka in trajanje, ki neposredno opredeljujeta spreminjanje zvočnega tlaka s časom; in
b) meritve časovno integriranih količin, kot je frekvenčno vrednotena raven zvočne izpostavljenosti ali raven zvočne energije.

General Information

Status
Published
Public Enquiry End Date
29-Jan-2012
Publication Date
18-Jan-2012
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
12-Jan-2012
Due Date
18-Mar-2012
Completion Date
19-Jan-2012

Relations

Buy Standard

Corrigendum
ISO 10843:2012/AC 1:2012
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
ISO 10843:2012/oCor 1:2012
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Akustika - Metode za opis in fizikalne meritve posameznih ali zaporednih impulzov -
Popravek (ISO 10843:1997/Cor 1:2009)Acoustics - Methods for the description and physical measurement of single impulses or series of impulses - Corrigendum (ISO 10843:1997/Cor 1:2009)17.140.20Emisija hrupa naprav in opremeNoise emitted by machines and equipmentICS:Ta slovenski standard je istoveten z:ISO 10843:1997/Cor 1:2009SIST ISO 10843:2012/AC 1:2012en01-februar-2012SIST ISO 10843:2012/AC 1:2012SLOVENSKI
STANDARD



SIST ISO 10843:2012/AC 1:2012



ICS
17.140.20 Ref. No. ISO 10843:1997/Cor.1:2009(E)©
ISO 2009 – All rights reserved Published in Switzerland
INTERNATIONAL STANDARD ISO 10843:1997 TECHNICAL CORRIGENDUM 1 Published 2009-04-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION •
• ORGANISATION INTERNATIONALE DE NORMALISATION
Acoustics — Methods for the description and physical measurement of single impulses or series of impulses TECHNICAL CORRIGENDUM 1 Acoustique — Métrique et techniques pour le mesurage physique de bruits impulsionnels isolés ou en courtes rafales RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 10843:1997 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 1, Noise.
Page ii, Contents Under “Annexes”, delete Annexes D and E. Add “Bibliography”. Page iii, Foreword, last line Delete “Annexes A to E”, insert “Annexes A to C”. Page 1, Clause 2 Delete all references, and insert: “IEC 60050-801:1994, International Electrotechnical Vocabulary — Chapter 801: Acoustics and electroacoustics IEC 60942:2003, Electroacoustics — Sound calibrators SIST ISO 10843:2012/AC 1:2012



ISO 10843:1997/Cor.1:2009(E) 2 ©
ISO 2009 – All rights reserved IEC 61094-4:1995, Measurement microphones — Part 4: Specifications for working standard microphones IEC 61260:1995, Electroacoustics — Octave-band and fractional-octave-band filters IEC 61672-1:2002, Electroacoustics — Sound level meters — Part 1: Specifications” Page 2, 3.1.1, Note 1 Delete “and annex E”. Delete “reference [25]”, insert “reference [27]”. Page 2, 3.1.2, Note Delete “and annex E”. Delete “reference [25]”, insert “reference [27]”. Page 2, 3.1.3, Note Delete “and annex E”. Delete “reference [34]”, insert “reference [27]”. Page 2, 3.1.4, line 2 Delete “instantaneous”. Page 4, 3.1.14, Note 1 Delete “20 µPa2·s”, insert “(20 µPa)2 s = 4 × 10−10 Pa2 s”. Page 5, 4.1, paragraph 2, lines 2 and 3 Delete “IEC 1094-4”, insert “IEC 61094-4”. Page 6, 4.3.2.1, line 1 Delete “instantaneous”. Page 7, 4.3.4 Delete “IEC 651 and IEC 804”, insert “IEC 61672-1”. Page 7, 4.3.6 Delete “IEC 651 for type 1”, insert “IEC 61672-1 for class 1”. Delete “; they should preferably meet the requirements for type 0 instruments”. Page 7, 4.3.7 Delete “IEC 1260”, insert “IEC 61260”. Page 7, 4.3.7, Note, last line Delete “European Community Machinery Directive 89/392/EEC”, insert “European Community Machinery Directive 2006/42/EC”. SIST ISO 10843:2012/AC 1:2012



ISO 10843:1997/Cor.1:2009(E) ©
ISO 2009 – All rights reserved 3 Page 7, 4.5.1.1, lines 1 and 2 Delete “type 1 requirements of IEC 651 and IEC 804 and should comply with the additional requirements of annex D.”, insert “class 1 requirements of IEC 61672-1.” Page 7, 4.5.1.1, Notes Delete “NOTES”. Delete the first note entirely. Delete “2”, insert “NOTE”. Page 8, 4.5.1.1, Note 2, last paragraph, line 3 Delete “SEL”, insert “single event sound exposure level”. Page 8, 4.5.1.1, Note 2, last line Delete “IEC 651 and in annex D.”, insert “IEC 61672-1.” Page 8, 4.5.2, lines 3 and 4 (twice) Delete “IEC 1094-4”, insert “IEC 61094-4”. Page 9, 5.3.1, line 2 Delete “IEC 942”, insert “IEC 60942”. Page 10, 5.5, line 6 Delete “BIPM/IEC/IFCC/ISO/IUPAC/IUPAP/OIML guide [25]”, insert “ISO/IEC Guide 98-3 [26]”. Page 11, 6.1.2, paragraph 2, line 1 Delete “IEC 1260”, insert “IEC 61260”. Page 13, Clause A.1, paragraph 1, penultimate line Delete “annex E,”. Page 19, Clause C.1, paragraph 1, line 2 Delete “(see annex E, reference [4])”. Page 19, Clause C.2, line 3 Delete “(see annex E, reference [5])”. Page 19, Clause C.3 Delete “IEC 651:1979, clause 9 and IEC 804:1985, clause 9”, insert “IEC 61672-2:2003, clause 9”. Page 19, Clause C.4 Delete “IEC 804:1985”, insert “IEC 61672-2:2003”. SIST ISO 10843:2012/AC 1:2012



ISO 10843:1997/Cor.1:2009(E) 4 ©
ISO 2009 – All rights reserved Page 20 Delete Annex D. Page 21 to 23 Delete Annex E, insert the following Bibliography. Bibliography [1] ISO 1996-1, Acoustics — Description, measurement and assessment of environmental noise — Part 1: Basic quantities and assessment procedures [2] ISO 1996-2, Acoustics — Description, measurement and assessment of environmental noise — Part 2: Determination of environmental noise levels [3] ISO 3740, Acoustics — Determination of sound power levels of noise sources — Guidelines for the use of basic standards [4] ISO 3741, Acoustics — Determination of sound power levels of noise sources using sound pressure — Precision methods for reverberation rooms [5] ISO 3743-1, Acoustics — Determination of sound power levels of noise sources — Engineering methods for small, movable sources in reverberant fields — Part 1: Comparison method for hard-walled test rooms [6] ISO 3743-2, Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms [7] ISO 3744, Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering method in an essentially free field over a reflecting plane [8] ISO 3745, Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for free-field test roo
...

SLOVENSKI STANDARD
oSIST ISO 10843:2012/oCor 1:2012
01-januar-2012
Akustika - Metode za opis in fizikalne meritve posameznih ali zaporednih impulzov
- Popravek (ISO 10843:1997/Cor 1:2009)
Acoustics - Methods for the description and physical measurement of single impulses or
series of impulses - Corrigendum (ISO 10843:1997/Cor 1:2009)
Ta slovenski standard je istoveten z: ISO 10843:1997/Cor 1:2009
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
oSIST ISO 10843:2012/oCor 1:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST ISO 10843:2012/oCor 1:2012

---------------------- Page: 2 ----------------------
oSIST ISO 10843:2012/oCor 1:2012
INTERNATIONAL STANDARD ISO 10843:1997
TECHNICAL CORRIGENDUM 1
Published 2009-04-15

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION


Acoustics — Methods for the description and physical
measurement of single impulses or series of impulses
TECHNICAL CORRIGENDUM 1
Acoustique — Métrique et techniques pour le mesurage physique de bruits impulsionnels isolés ou en courtes
rafales
RECTIFICATIF TECHNIQUE 1
Technical Corrigendum 1 to ISO 10843:1997 was prepared by Technical Committee ISO/TC 43, Acoustics,
Subcommittee SC 1, Noise.

Page ii, Contents
Under “Annexes”, delete Annexes D and E.
Add “Bibliography”.
Page iii, Foreword, last line
Delete “Annexes A to E”, insert “Annexes A to C”.
Page 1, Clause 2
Delete all references, and insert:
“IEC 60050-801:1994, International Electrotechnical Vocabulary — Chapter 801: Acoustics and
electroacoustics
IEC 60942:2003, Electroacoustics — Sound calibrators
ICS 17.140.20 Ref. No. ISO 10843:1997/Cor.1:2009(E)
©  ISO 2009 – All rights reserved
Published in Switzerland

---------------------- Page: 3 ----------------------
oSIST ISO 10843:2012/oCor 1:2012
ISO 10843:1997/Cor.1:2009(E)
IEC 61094-4:1995, Measurement microphones — Part 4: Specifications for working standard microphones
IEC 61260:1995, Electroacoustics — Octave-band and fractional-octave-band filters
IEC 61672-1:2002, Electroacoustics — Sound level meters — Part 1: Specifications”
Page 2, 3.1.1, Note 1
Delete “and annex E”.
Delete “reference [25]”, insert “reference [27]”.
Page 2, 3.1.2, Note
Delete “and annex E”.
Delete “reference [25]”, insert “reference [27]”.
Page 2, 3.1.3, Note
Delete “and annex E”.
Delete “reference [34]”, insert “reference [27]”.
Page 2, 3.1.4, line 2
Delete “instantaneous”.
Page 4, 3.1.14, Note 1
2 2 −10 2
Delete “20 µPa ·s”, insert “(20 µPa) s = 4 × 10 Pa s”.
Page 5, 4.1, paragraph 2, lines 2 and 3
Delete “IEC 1094-4”, insert “IEC 61094-4”.
Page 6, 4.3.2.1, line 1
Delete “instantaneous”.
Page 7, 4.3.4
Delete “IEC 651 and IEC 804”, insert “IEC 61672-1”.
Page 7, 4.3.6
Delete “IEC 651 for type 1”, insert “IEC 61672-1 for class 1”.
Delete “; they should preferably meet the requirements for type 0 instruments”.
Page 7, 4.3.7
Delete “IEC 1260”, insert “IEC 61260”.
Page 7, 4.3.7, Note, last line
Delete “European Community Machinery Directive 89/392/EEC”, insert “European Community Machinery
Directive 2006/42/EC”.
2 ©  ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST ISO 10843:2012/oCor 1:2012
ISO 10843:1997/Cor.1:2009(E)
Page 7, 4.5.1.1, lines 1 and 2
Delete “type 1 requirements of IEC 651 and IEC 804 and should comply with the additional requirements of
annex D.”, insert “class 1 requirements of IEC 61672-1.”
Page 7, 4.5.1.1, Notes
Delete “NOTES”.
Delete the first note entirely.
Delete “2”, insert “NOTE”.
Page 8, 4.5.1.1, Note 2, last paragraph, line 3
Delete “SEL”, insert “single event sound exposure level”.
Page 8, 4.5.1.1, Note 2, last line
Delete “IEC 651 and in annex D.”, insert “IEC 61672-1.”
Page 8, 4.5.2, lines 3 and 4 (twice)
Delete “IEC 1094-4”, insert “IEC 61094-4”.
Page 9, 5.3.1, line 2
Delete “IEC 942”, insert “IEC 60942”.
Page 10, 5.5, line 6
[25] [26]
Delete “BIPM/IEC/IFCC/ISO/IUPAC/IUPAP/OIML guide ”, insert “ISO/IEC Guide 98-3 ”.
Page 11, 6.1.2, paragraph 2, line 1
Delete “IEC 1260”, insert “IEC 61260”.
Page 13, Clause A.1, paragraph 1, penultimate line
Delete “annex E,”.
Page 19, Clause C.1, paragraph 1, line 2
Delete “(see annex E, reference [4])”.
Page 19, Clause C.2, line 3
Delete “(see annex E, reference [5])”.
Page 19, Clause C.3
Delete “IEC 651:1979, clause 9 and IEC 804:1985, clause 9”, insert “IEC 61672-2:2003, clause 9”.
Page 19, Clause C.4
Delete “IEC 804:1985”, insert “IEC 61672-2:2003”.
©  ISO 2009 – All rights reserved 3

---------------------- Page: 5 ----------------------
oSIST ISO 10843:2012/oCor 1:2012
ISO 10843:1997/Cor.1:2009(E)
Page 20
Delete Annex D.
Page 21 to 23
Delete Annex E, insert the following Bibliography.
Bibliography
[1] ISO 1996-1, Acoustics — Description, measurement and assessment of environmental noise — Part 1:
Basic quantities and assessment procedures
[2] ISO 1996-2, Acoustics — Description, measurement and assessment of environmental noise — Part 2:
Determination of environmental noise levels
[3] ISO 3740, Acoustics — Determination of sound power levels of noise sources — Guidelines for the use
of basic standards
[4] ISO 3741, Acoustics — Determination of sound power levels of noise sources using sound pressure —
Precision methods for reverberation rooms
[5] ISO 3743-1, Acoustics — Determination of sound power levels of noise sources — Engineering
methods for small, movable sources in reverberant fields — Part 1: Comparison method for
hard-walled test rooms
[6] ISO 3743-2, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods
for special reverberation test rooms
[7] ISO 3744, Acoustics — Determination of sound power levels of noise sources using sound pressure —
Engineering method in an essentially free field over a reflecting plane
[8] ISO 3745, Acoustics — Determination of sound power levels and sound
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.