This document specifies performance requirements for type tests for transition joints for use between extruded
insulated power cables as specified in HD 620 and impregnated paper insulated power cables as specified in
HD 621 or another relevant standard.
Once type test for an accessory is successfully completed, it is not necessary to repeat the test, unless
changes are made in the materials, design or manufacturing process, which might affect the performance
characteristics.
Possible extra thermo-mechanical forces due to high current loads from renewable sources of power
generation are not covered by these tests (under consideration).
Accessories for special applications such as submarine cables, ships cables or hazardous situations (explosive
environments, fire resistant cables or seismic conditions) are not included.
Test methods are included in EN IEC 61442:— and Annex E.
NOTE 1 This document does not invalidate existing approvals of products achieved on the basis of national standards
and specifications and/or the demonstration of satisfactory service performance. However, products approved according
to such national standards or specifications cannot directly claim approval to this document.
NOTE 2 It might be possible, subject to agreement between supplier and purchaser, and/or the relevant conformity
assessment body, to demonstrate that conformity to the earlier standard can be used to claim conformity to this document,
provided an assessment is made of any additional type testing that might need to be carried out. Any such additional
testing that is part of a sequence of testing cannot be done separately.

  • Standardization document
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies performance requirements for type tests for cable accessories for use on impregnated
paper insulated power cables as specified in HD 621.
It is not necessary to repeat these tests, once successfully completed, unless changes are made in the
materials, design or manufacturing process, which might affect the performance characteristics.
Accessories for special applications such as submarine cables, ships cables or hazardous situations (explosive
environments, fire resistant cables or seismic conditions) are not included.
Test methods are included in EN 61442:2005.
NOTE It might be possible, subject to agreement between supplier and purchaser, and/or the relevant conformity
assessment body, to demonstrate that conformity to the earlier standard can be used to claim conformity to this document,
provided an assessment is made of any additional type testing that might need to be carried out. Any such additional
testing that is part of a sequence of testing cannot be done separately.

  • Standardization document
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1 General This document specifies performance requirements for type tests for transition joints for use between extruded insulated power cables as specified in HD 620 and impregnated paper insulated power cables as specified in HD 621 or another relevant standard. Once type test for an accessory is successfully completed, it is not necessary to repeat the test, unless changes are made in the materials, design or manufacturing process, which might affect the performance characteristics. Possible extra thermo-mechanical forces due to high current loads from renewable sources of power generation are not covered by these tests (under consideration). Accessories for special applications such as submarine cables, ships cables or hazardous situations (explosive environments, fire resistant cables or seismic conditions) are not included. Test methods are included in EN IEC 61442:- and Annex E. NOTE 1 This document does not invalidate existing approvals of products achieved on the basis of national standards and specifications and/or the demonstration of satisfactory service performance. However, products approved according to such national standards or specifications cannot directly claim approval to this document. NOTE 2 It might be possible, subject to agreement between supplier and purchaser, and/or the relevant conformity assessment body, to demonstrate that conformity to the earlier standard can be used to claim conformity to this document, provided an assessment is made of any additional type testing that might need to be carried out. Any such additional testing that is part of a sequence of testing cannot be done separately. 1.2 Type of accessories The accessories covered by this document are straight and branch transition joints of all designs, suitable for use underground or in air. 1.3 Rated voltage The rated voltages U0/U (Um) of the accessories covered by this document are 3,6/6(7,2) - 3,8/6,6(7,2) - 6/10(12) - 6,35/11(12) - 8,7/15(17,5) - 12/20(24) - 12,7/22(24) - 18/30(36) - 19/33(36) - 20,8/36(42) kV.

  • Standardization document
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60793-2: 2023 Amendment 1

  • Standard
    8 pages
    English and French language
    sale 15% off

IEC 60763-2:2007 gives methods of test applicable for the material classified in IEC 60763-1. This edition includes the following significant technical changes with respect to the previous edition:
The standard has generally been revised editorially and brought into line with IEC 60641-2;
The test method for the determination of the internal ply strength has been replaced with an alternative method; and
The test method for the determination of the thermal resistance has been enlarged in its scope.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    37 pages
    English and French language
    sale 15% off
  • Standard
    80 pages
    English and French language
    sale 15% off

IEC TR 63043:2020(E), which is a technical report, describes common practices and state of the art for renewable energy power forecasting technology, including general data demands, renewable energy power forecasting methods and forecasting error evaluation. For the purposes of this document, renewable energy refers to variable renewable energy, which mainly comprises wind power and photovoltaic (PV) power – these are the focus of the document. Other variable renewable energies, like concentrating solar power, wave power and tidal power, etc., are not presented in this document, since their capacity is small, while hydro power forecasting is a significantly different field, and so not covered here.
The objects of renewable energy power forecasting can be wind turbines, or a wind farm, or a region with lots of wind farms (respectively PV systems, PV power stations and regions with high PV penetration). This document focuses on providing technical guidance concerning forecasting technologies of multiple spatial and temporal scales, probabilistic forecasting, and ramp event forecasting for wind power and PV power.
This document outlines the basic aspects of renewable energy power forecasting technology. This is the first IEC document related to renewable energy power forecasting. The contents of this document will find an application in the following potential areas:
• support the development and future research for renewable energy power forecasting technology, by showing current state of the art;
• evaluation of the forecasting performance during the design and operation of renewable energy power forecasting system;
• provide information for benchmarking renewable forecasting technologies, including methods used, data required and evaluation techniques

  • Technical report
    138 pages
    English language
    sale 15% off

This part of IEC 60667 gives methods of test for vulcanized fibre sheets for electrical purposes.
Material made by combining with an adhesive several thicknesses of vulcanized fibre is not
covered by this document.
Materials which conform to this specification meet established levels of performance. However,
the selection of a material by a user for a specific application is based on the actual
requirements necessary for adequate performance in that application and not based on this
specification alone.
Safety warning: It is the responsibility of the user of the methods contained or referred to in this
document to ensure that they are used in a safe manner.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60667-2:2020 gives methods of test for vulcanized fibre sheets for electrical purposes. Material made by combining with an adhesive several thicknesses of vulcanized fibre is not covered by this document. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1982. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) added Terms and definitions b) added General notes on tests c) added Thickness instead of dimension d) changed Apparent density from Density e) added Arc resistance f) deleted Sulphate content g) added method (Bending) for flexibility h) changed test method for internal ply adhesion i) added Shrinkage

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60667 gives the definitions and general requirements for vulcanized fibre
sheets for electrical purposes. Materials made by combining with an adhesive several
thicknesses of vulcanized fibre are not covered by this document.
Materials that conform to this specification meet established levels of performance. However,
the selection of a material by a user for a specific application is based on the actual
requirements necessary for adequate performance in that application and not based on this
specification alone.
Safety warning: it is the responsibility of the user of the methods contained or referred to in this
document to ensure that they are used in a safe manner.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60667 gives requirements for vulcanized fibre sheets for electrical purposes.
Materials made by combining with an adhesive several thicknesses of vulcanized fibre are not
covered by this document.
Materials that conform to this specification meet established levels of performance. However,
the selection of a material by a user for a specific application is based on the actual
requirements necessary for adequate performance in that application and not based on this
specification alone.
Safety warning: it is the responsibility of the user of the methods contained or referred to in this
document to ensure that they are used in a safe manner.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60667-1:2020 gives the definitions and general requirements for vulcanized fibre sheets for electrical purposes. Materials made by combining with an adhesive several thicknesses of vulcanized fibre are not covered by this document. Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: it is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1980. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
deletion of "corrugated, round rods, and round tubes" from the Scope;
types A, B and C replaced by general and fishpaper types and addition of a symbol for each type in the classification;
addition of white, blue, brown, and addition of a symbol for each colour;
deletion of the thickness of 15,0 mm, the length, the mass and the dimension of rolls from the general requirements;
addition of the manufacturer's name, trademark (if any), nominal thickness, manufacture date, and lot number in the conditions of supply.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60667-3-1: 2020 gives requirements for vulcanized fibre sheets for electrical purposes. Materials made by combining with an adhesive several thicknesses of vulcanized fibre are not covered by this document. Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: it is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1986. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
change to the range of thickness deviation in Table 1;
addition of apparent density in Table 1;
change to the range of thickness for tensile strength in Table 1;
addition of flexibility and shrinkage in Table 1;
change test method and property value of internal ply adhesion on Table 1.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60667-2:2020 gives methods of test for vulcanized fibre sheets for electrical purposes. Material made by combining with an adhesive several thicknesses of vulcanized fibre is not covered by this document. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1982. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) added Terms and definitions
b) added General notes on tests
c) added Thickness instead of dimension
d) changed Apparent density from Density
e) added Arc resistance
f) deleted Sulphate content
g) added method (Bending) for flexibility
h) changed test method for internal ply adhesion
i) added Shrinkage

  • Standard
    28 pages
    English and French language
    sale 15% off

IEC 60667-1:2020 gives the definitions and general requirements for vulcanized fibre sheets for electrical purposes. Materials made by combining with an adhesive several thicknesses of vulcanized fibre are not covered by this document. Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: it is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1980. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
deletion of "corrugated, round rods, and round tubes" from the Scope;
types A, B and C replaced by general and fishpaper types and addition of a symbol for each type in the classification;
addition of white, blue, brown, and addition of a symbol for each colour;
deletion of the thickness of 15,0 mm, the length, the mass and the dimension of rolls from the general requirements;
addition of the manufacturer's name, trademark (if any), nominal thickness, manufacture date, and lot number in the conditions of supply.

  • Standard
    17 pages
    English and French language
    sale 15% off

IEC 60667-3-1: 2020 gives requirements for vulcanized fibre sheets for electrical purposes. Materials made by combining with an adhesive several thicknesses of vulcanized fibre are not covered by this document. Materials that conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: it is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 1986. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
change to the range of thickness deviation in Table 1;
addition of apparent density in Table 1;
change to the range of thickness for tensile strength in Table 1;
addition of flexibility and shrinkage in Table 1;
change test method and property value of internal ply adhesion on Table 1.

  • Standard
    16 pages
    English and French language
    sale 15% off

IEC 60819-3-4:2013 specifies requirements for two types of aramid fibre paper containing mica particles and designated as PAaM: - type 1: calendered aramid paper containing mica particles; - type 2: uncalendered aramid paper containing mica particles. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 2001. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: the document was updated including new thicknesses and relevant values as from Table 1. Keywords: aramid fibre paper containing mica particles, PAaM, calendered, uncalendered

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Describes methods for the determination of water in insulating liquids and in oil-impregnated cellulosic insulation with coulmetrically generated Karl Fischer reagent.

  • Standard
    16 pages
    English and French language
    sale 15% off

IEC 60819-1:2009 gives the definitions and general requirements for non-cellulosic papers for electrical purposes. The main changes from the previous edition are as follows: the list of materials to be used in combination was updated with the addition of new materials made available by progress in technology and described in Subclauses 2.7 and 2.8.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60819-3-3:2011 is a sheet of IEC 60819-3 specifies requirements for four types of unfilled aramid papers: - Type 1: calendered paper; - Type 2: calendered paper, with improved tearing resistance and conformability; - Type 3: uncalendered paper; - Type 4: calendered paper, with lower density for laminating. This edition includes the following significant technical changes with respect to the previous edition: - normative references change: all the requirements are now determined according the clauses of test methods from IEC 60819-2 specific for non cellulosic papers, instead of IEC 60554-2:2001 generally valid for cellulosic papers; - and some new, very thin thicknesses, of type 4, calendered paper with lower density for laminating, were added.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN IEC 60819-3-4 specifies requirements for two types of aramid fibre paper containing mica particles and designated as PAaM. - type 1: calendered aramid paper containing mica particles; - type 2: uncalendered aramid paper containing mica particles. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60763-3-1:2010 gives the requirements for laminated precompressed boards comprised of 100 % sulphate wood pulp. The main changes with respect to the previous edition are: - requirements for the new properties in Part 2 have been integrated; - specifications for type LB3.3.1 and LB3.3.2 have been deleted.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60763-1:2010 contains the definitions required for the understanding of all three parts of IEC 60763, the classification of material into types, and the general requirements applicable to all material covered by the standard. The main changes with respect to the previous edition is that the specification was brought in line with the second edition of IEC 60641-1(2007).

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60819-3-4:2013 specifies requirements for two types of aramid fibre paper containing mica particles and designated as PAaM:
- type 1: calendered aramid paper containing mica particles;
- type 2: uncalendered aramid paper containing mica particles. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner. This second edition cancels and replaces the first edition published in 2001. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: the document was updated including new thicknesses and relevant values as from Table 1. Keywords: aramid fibre paper containing mica particles, PAaM, calendered, uncalendered

  • Standard
    17 pages
    English and French language
    sale 15% off

This part of IEC 60819 gives the definitions and general requirements for non-cellulosic papers for electrical purposes. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This specification covers material having a nominal thickness from 0,05 mm to 0,15 mm, supplied either in the form of sheets or rolls.[
]The contents of the corrigendum of August 1995 have been included in this copy.

  • Standard
    24 pages
    English and French language
    sale 15% off

IEC 60793-1-54:2012 outlines a method for measuring the steady state response of optical fibres and optical cables exposed to gamma radiation. It can be employed to determine the level of radiation induced attenuation produced in Class B single-mode or Class A, category A1 and A2 multimode optical fibres, in either cabled or uncabled form, due to exposure to gamma radiation. This second edition cancels and replaces the first edition, published in 2003. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: launching conditions and optical sources have been reviewed and are better defined. Keywords: gamma radiation, optical fibres, optical cables

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    26 pages
    English and French language
    sale 15% off

IEC 60512-16-21:2012 The object of this standard is to define a standard test method to assess the possibility of whisker growth by external mechanical stress on the tin and tin-alloy plated parts of a connector in its application (after wire termination, after soldering, after mounting, mated with counterpart). This standard does not cover internal stress type whisker. This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. Keywords: Whisker growth, external mechanical stress

  • Standard
    21 pages
    English and French language
    sale 15% off

This sheet of IEC 60819-3 specifies requirements for four types of unfilled aramid papers: Type 1: calendered paper; Type 2: calendered paper, with improved tearing resistance and conformability; Type 3: uncalendered paper; Type 4: calendered paper, with lower density for laminating. Materials which conform to this specification meet established levels of performance. However, the selection of material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60819-3-3:2011 is a sheet of IEC 60819-3 specifies requirements for four types of unfilled aramid papers:
- Type 1: calendered paper;
- Type 2: calendered paper, with improved tearing resistance and conformability;
- Type 3: uncalendered paper;
- Type 4: calendered paper, with lower density for laminating.
This edition includes the following significant technical changes with respect to the previous edition:
- normative references change: all the requirements are now determined according the clauses of test methods from IEC 60819-2 specific for non cellulosic papers, instead of IEC 60554-2:2001 generally valid for cellulosic papers;
- and some new, very thin thicknesses, of type 4, calendered paper with lower density for laminating, were added.

  • Standard
    16 pages
    English and French language
    sale 15% off

IEC 60641-3-1:2008 gives the requirements for pressboard for electrical purposes comprised of 100 % sulphate wood pulp or a mixture of sulphate wood pulp and cotton. The main changes with respect to the previous edition are: - Requirements for types B.0.3 and B.5.3 were added; - The precompressed type B.3.1 was divided in B.3.1A and B.3.1B (higher flexibility); - Types B.6.1 has been replaced with a new type, but the designation has been kept; - Type B.7.1 has been deleted; - The thickness relation of the properties has been simplified; and - The values were adjusted to today's needs of users.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62271-204:2011 applies to rigid HV gas insulated transmission lines (GIL) in which the insulation is obtained, at least partly, by a non-corrosive insulating gas, other than air at atmospheric pressure, for alternating current of rated voltages above 52 kV, and for service frequencies up to and including 60 Hz. This standard cancels and replaces IEC/TS 61640:1998. It is a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- update to be in line with IEC 62271-1:2007 and 62271-203 and alignment of the voltage ratings and the test voltages;
- addition of new information for gas tightness and corrosion protection.
This publication is to be read in conjunction with IEC 62271-1:2007.

  • Standard
    109 pages
    English and French language
    sale 15% off

Gives the general definitions and requirements for non-cellulosic papers (aramid (aromatic polyamide) paper, polyethylene paper, polypropylene paper, glass paper, ceramic paper, poly(ethylene)-terephthalate paper)

  • Standard
    10 pages
    English and French language
    sale 15% off

This part of IEC 60641 gives the requirements for presspaper for electrical purposes comprised of 100 % sulphate wood pulp, 100 % cotton or a mixture of sulphate wood pulp and cotton. The main changes with respect to the previous edition are: type P.6 has been replaced with a new type, but the designation has been kept, type P.7 has been deleted, the thickness relation of the properties has been simplified and the values were adjusted to today's needs of users.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60763 contains the definitions required for the understanding of all three parts of IEC 60763, the classification of material into types, and the general requirements applicable to all material covered by the standard. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This sheet of IEC 60763-3 gives the requirements for laminated precompressed boards comprised of 100 % sulphate wood pulp. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60641 contains definitions related to a classification of, and the general requirements to be fulfilled by, pressboard and presspaper for electrical purposes. The main changes with respect to the previous edition are: the kind of surface finish shall no longer be specified in the standard, fixed nominal thicknesses have been replaced by preferred thicknesses, types B.6 and P.6 have been replaced, but the designations have been kept and types B.7 and P.7 have been deleted.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60763-3-1:2010 gives the requirements for laminated precompressed boards comprised of 100 % sulphate wood pulp. The main changes with respect to the previous edition are:
- requirements for the new properties in Part 2 have been integrated;
- specifications for type LB3.3.1 and LB3.3.2 have been deleted.

  • Standard
    9 pages
    English and French language
    sale 15% off

IEC 60763-1:2010 contains the definitions required for the understanding of all three parts of IEC 60763, the classification of material into types, and the general requirements applicable to all material covered by the standard. The main changes with respect to the previous edition is that the specification was brought in line with the second edition of IEC 60641-1(2007).

  • Standard
    12 pages
    English and French language
    sale 15% off

Contains the requirements for pressure-sensitive adhesive tapes made with cellulosic paper, creped and non-creped, with rubber thermosetting adhesive.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

15/340/RVC established on 2006-07-07: To be published without FDIS stage

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60763-2:2007 gives methods of test applicable for the material classified in IEC 60763-1. This edition includes the following significant technical changes with respect to the previous edition: The standard has generally been revised editorially and brought into line with IEC 60641-2; The test method for the determination of the internal ply strength has been replaced with an alternative method; and The test method for the determination of the thermal resistance has been enlarged in its scope.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60819-1:2009 gives the definitions and general requirements for non-cellulosic papers for electrical purposes. The main changes from the previous edition are as follows: the list of materials to be used in combination was updated with the addition of new materials made available by progress in technology and described in Subclauses 2.7 and 2.8.

  • Standard
    16 pages
    English and French language
    sale 15% off

This part of IEC 60371 gives requirements for electrical insulating materials made by combining mica paper with glass fabric and bonding them together with a small amount of epoxy resin.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of EN 60371 gives requirements for electrical insulating materials made from mica paper which is to be processed for built-up mica materials according to EN 60371-1, such as rigid flat mica materials, flexible mica materials, curable flexible mica materials and shaped pieces.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Ingrid Glavich Ingrid Glavich 2 1 1995-11-10T13:27:00Z 2008-11-17T14:52:00Z 2008-11-17T14:52:00Z 1 84 480 4 1 563 10.6845    21 0 0            MicrosoftInternetExplorer4    /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}        
ISO/IEC 29341-3-12:2008(E) defines the a content directory service which enables the user to acces various types of content that other devices would like to access, such as music, videos and still images. The series of ISO/IEC 29341 publications defines an architecture for pervasive peer-to-peer network connectivity of intelligent appliances, wireless devices and PCs. It is designed to bring easy to use, flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a small business, public spaces or attached to the Internet.

  • Standard
    86 pages
    English language
    sale 15% off

ISO/IEC 29341-3-10:2008(E) defines a common model for AV transport control suitable for generic user interface. The series of ISO/IEC 29341 publications defines an architecture for pervasive peer-to-peer network connectivity of intelligent appliances, wireless devices and PCs. It is designed to bring easy to use, flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a small business, public spaces or attached to the Internet.

  • Standard
    56 pages
    English language
    sale 15% off