Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments

applies to electrical and electronic apparatus intended for use in industrial environments, as described below. Immunity requirements in the frequency range 0 Hz to 400 GHz are covered. No tests need to be performed at frequencies where no requirements are specified. This generic EMC immunity standard is applicable if no relevant dedicated product or product-family EMC immunity standard exists. This standard applies to apparatus intended to be connected to a power network supplied from a high or medium voltage transformer dedicated to the supply of an installation feeding manufacturing or similar plant, and intended to operate in or in proximity to industrial locations, as described below. This standard applies also to apparatus which is battery operated and intended to be used in industrial locations. The environments encompassed by this standard are industrial, both indoor and outdoor. The immunity requirements have been selected to ensure an adequate level of immunity for apparatus at industrial locations. The levels do not, however, cover extreme cases, which may occur at any location, but with an extremely low probability of occurrence. Not all disturbance phenomena have been included for testing purposes in this standard, but only those considered as relevant for the equipment covered by this standard. These test requirements represent essential electromagnetic compatibility immunity requirements.

Elektromagnetische Verträglichkeit (EMV) - Teil 6-2: Fachgrundnormen - Störfestigkeit für Industriebereiche

Compatibilité électromagnétique (CEM) - Partie 6-2: Normes génériques - Norme d'immunité pour les environnements industriels

S'applique aux appareils électriques et électroniques destinés à être utilisés dans des environnements industriels, tels qu'ils sont décrits ci-dessous. Cette partie couvre les exigences d'immunité dans la gamme de fréquences de 0 kHz à 400 GHz. Il n'est pas nécessaire de réaliser des essais aux fréquences pour lesquelles aucune exigence n'est spécifiée. Cette norme générique d'immunité CEM s'applique en l'absence de norme d'immunité CEM applicable spécifique à un produit ou à une famille de produits. Les appareils couverts par cette norme sont destinés à être raccordés à un réseau d'énergie alimenté par un transformateur haute tension ou moyenne tension réservé à l'alimentation d'une l'installation alimentant un site industriel ou analogue, et destinés à fonctionner à l'intérieur ou à proximité des sites industriels, comme défini ci-dessous. Cette norme s'applique également aux appareils qui sont alimentés par piles ou accumulateurs et qui sont destinés à être utilisés dans des sites industriels. Les environnements couverts par cette norme sont les environnements industriels, intérieurs et extérieurs. Les exigences d'immunité ont été choisies pour assurer un niveau adéquat d'immunité pour les appareils utilisés sur des sites industriels. Ces niveaux ne couvrent pas cependant les cas extrêmes qui peuvent apparaître, mais avec une très faible probabilité, sur un site quelconque. Cette norme ne comporte pas, pour les besoins des essais, tous les phénomènes perturbateurs mais uniquement ceux considérés comme applicables pour les appareils couverts par la norme. Ces exigences d'essais représentent les exigences essentielles de compatibilité électromagnétique concernant l'immunité.

Elektromagnetna združljivost (EMC) - 6-2. del: Osnovni standardi - Odpornost za industrijska okolja

Ta standard se uporablja za električne in elektronske naprave, ki so namenjene uporabi v industrijskih okoljih, kot je opisano spodaj. Zajema zahteve glede odpornosti v frekvenčnem razponu od 0 Hz do 400 GHz. Za frekvence, za katere ni določenih zahtev, ni treba opraviti preskusov. Ta generični standard o odpornosti proti elektromagnetnim motnjam se uporablja, če ne obstaja ustrezen poseben standard o odpornosti proti elektromagnetnim motnjam za izdelek ali družino izdelkov. Ta standard se uporablja za naprave, ki so namenjene za povezavo z napajalnim omrežjem, ki se napaja iz visoko- ali srednjenapetostnega transformatorja, namenjenega za napajanje inštalacije, ki napaja proizvodni ali podoben obrat, in za delovanje v industrijskih okoljih ali v njihovi bližini, kot je opisano spodaj. Ta standard se uporablja tudi za naprave, ki delujejo na baterije in so namenjene za uporabo v industrijskih okoljih. Ta standard zajema industrijska okolja, in sicer v zaprtih prostorih in na prostem. Zahteve glede odpornosti so izbrane tako, da zagotavljajo ustrezno raven odpornosti naprav v industrijskih okoljih. Vendar stopnje ne zajemajo izjemnih primerov, ki se lahko zgodijo na kateri koli lokaciji, čeprav je verjetnost zelo majhna. Ta standard ne zajema vseh motenj za namene preskušanja, ampak le motnje, ki so pomembne za opremo, zajeto v tem standardu. Te zahteve za preskus predstavljajo osnovne zahteve glede odpornosti v zvezi z elektromagnetno združljivostjo.

General Information

Status
Published
Publication Date
21-Feb-2019
Withdrawal Date
21-Feb-2022
Current Stage
6060 - Document made available - Publishing
Start Date
22-Feb-2019
Completion Date
22-Feb-2019

Relations

Buy Standard

Standard
EN IEC 61000-6-2:2019
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2019
Nadomešča:
SIST EN 61000-6-2:2005
Elektromagnetna združljivost (EMC) - 6-2. del: Osnovni standardi - Odpornost za
industrijska okolja
Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard
for industrial environments
Elektromagnetische Verträglichkeit (EMV) - Teil 6-2: Fachgrundnormen - Störfestigkeit
für Industriebereiche
Compatibilité électromagnétique (CEM) - Partie 6-2: Normes génériques - Immunité pour
les environnements industriels
Ta slovenski standard je istoveten z: EN IEC 61000-6-2:2019
ICS:
33.100.20 Imunost Immunity
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61000-6-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2019
ICS 33.100.20 Supersedes EN 61000-6-2:2005
English Version
Electromagnetic compatibility (EMC) - Part 6-2: Generic
standards - Immunity standard for industrial environments
(IEC 61000-6-2:2016)
Compatibilité électromagnétique (CEM) - Partie 6-2: Elektromagnetische Verträglichkeit - Teil 6-2:
Normes génériques - Norme d'immunité pour les Fachgrundnormen - Störfestigkeit für Industriebereiche
environnements industriels (IEC 61000-6-2:2016)
(IEC 61000-6-2:2016)
This European Standard was approved by CENELEC on 2016-09-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61000-6-2:2019 E

European foreword
The text of document 77/521/FDIS, future edition 3 of IEC 61000-6-2, prepared by IEC/TC 77
"Electromagnetic compatibility" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61000-6-2:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-08-22
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-02-22
document have to be withdrawn
This document supersedes EN 61000-6-2:2005.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 61000-6-2:2016 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61000-4-12 NOTE Harmonized as EN 61000-4-12
IEC 61000-4-13 NOTE Harmonized as EN 61000-4-13
IEC 61000-4-16 NOTE Harmonized as EN 61000-4-16
IEC 61000-4-18 NOTE Harmonized as EN 61000-4-18
IEC 61000-4-19 NOTE Harmonized as EN 61000-4-19
IEC 61000-4-29 NOTE Harmonized as EN 61000-4-29
IEC 61000-4-31 NOTE Harmonized as EN 61000-4-31
CISPR 11:2009 NOTE Harmonized as EN 55011:2009 (modified).

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-161 -  International Electrotechnical Vocabulary. - -
Chapter 161: Electromagnetic compatibility
IEC 61000-4-2 2008 Electromagnetic compatibility (EMC) - PartE N 61000-4-2 2009
4-2: Testing and measurement techniques
- Electrostatic discharge immunity test
IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - PartE N 61000-4-3 2006
4-3 : Testing and measurement techniques
- Radiated, radio-frequency,
electromagnetic field immunity test
+ A1 2007  + A1 2008
+ A2 2010  + A2 2010
IEC 61000-4-4 2012 Electromagnetic compatibility (EMC) - PartE N 61000-4-4 2012
4-4: Testing and measurement techniques
- Electrical fast transient/burst immunity
test
IEC 61000-4-5 2014 Electromagnetic compatibility (EMC) - PartE N 61000-4-5 2014
4-5: Testing and measurement techniques
- Surge immunity test
IEC 61000-4-6 2013 Electromagnetic compatibility (EMC) - PartE N 61000-4-6 2014
4-6: Testing and measurement techniques
- Immunity to conducted disturbances,
induced by radio-frequency fields
IEC 61000-4-8 2009 Electromagnetic compatibility (EMC) - PartE N 61000-4-8 2010
4-8: Testing and measurement techniques
- Power frequency magnetic field immunity
test
IEC 61000-4-11 2004 Electromagnetic compatibility (EMC) - PartE N 61000-4-11 2004
4-11: Testing and measurement
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests
Publication Year Title EN/HD Year
IEC 61000-4-20 2010 Electromagnetic compatibility (EMC) - PartE N 61000-4-20 2010
4-20: Testing and measurement
techniques - Emission and immunity
testing in transverse electromagnetic
(TEM) waveguides
IEC 61000-4-21 2011 Electromagnetic compatibility (EMC) - PartEN 61000-4-21 2011
4-21: Testing and measurement
techniques - Reverberation chamber test
methods
IEC 61000-4-22 2010 Electromagnetic compatibility (EMC) - PartE N 61000-4-22 2011
4-22: Testing and measurement
techniques - Radiated emissions and
immunity measurements in fully anechoic
rooms (FARs)
IEC 61000-4-34 2005 Electromagnetic compatibility (EMC) - PartE N 61000-4-34 2007
4-34: Testing and measurement
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests for equipment with input
current more than 16 A per phase
+ A1 2009  + A1 2009
IEC 61000-6-2 ®
Edition 3.0 2016-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electromagnetic compatibility (EMC) –

Part 6-2: Generic standards – Immunity standard for industrial environments

Compatibilité électromagnétique (CEM) –

Partie 6-2: Normes génériques – Norme d'immunité pour les environnements

industriels
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.100.20 ISBN 978-2-8322-3566-9

– 2 – IEC 61000-6-2:2016 © IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references. 6
3 Terms and definitions . 7
4 Performance criteria . 9
5 Conditions during testing . 9
6 Product documentation . 10
7 Applicability . 10
8 Measurement uncertainty . 10
9 Immunity test requirements . 10
Annex A (informative) Guidance for product committees . 16
Bibliography . 18

Figure 1 – Equipment ports . 8

Table 1 – Immunity requirements – Enclosure ports . 12
Table 2 – Immunity requirements – Signal/control ports . 13
Table 3 – Immunity requirements – Input and output DC power ports . 14
Table 4 – Immunity requirements – Input and output AC power ports . 15
Table A.1 – Immunity tests and test levels to be considered in future or for particular
product families . 17

IEC 61000-6-2:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 6-2: Generic standards –
Immunity standard for industrial environments

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publ
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.