oSIST prEN 12814-2:2019

SLOVENSKI STANDARD
oSIST prEN 12814-2:2019
01-september-2019
Preskušanje zvarjenih spojev plastomernih polizdelkov - 2. del: Trgalni preskus

Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test

Essais des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 2 :

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Essais des assemblages soudés sur produits semi-finis Prüfen von Schweißverbindungen aus

en thermoplastiques - Partie 2 : Essai de traction thermoplastischen Kunststoffen - Teil 2: Zugversuch

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12814-2:2019 E

European foreword ...........................................................................................................................................................3

1 Scope ..............................................................................................................................................................................4

2 Normative references ..............................................................................................................................................4

3 Symbols and designations .....................................................................................................................................4

4 Principle of the test ..................................................................................................................................................5

5 Sampling procedures ...............................................................................................................................................5

6 Dimensions of test specimens ..............................................................................................................................5

7 Cutting of test specimens .......................................................................................................................................8

8 Mechanical testing ....................................................................................................................................................8

9 Test equipment ..........................................................................................................................................................8

10 Determination of the short-term tensile welding factor ............................................................................8

11 Test report ...................................................................................................................................................................9

Annex A (informative) Tensile test specimen for overlap joints ................................................................... 11

Annex B (informative) Recommended test speeds for some thermoplastics materials ....................... 12

Annex C (informative) Notched tensile test specimen ....................................................................................... 13

Bibliography ..................................................................................................................................................................... 14

This document (prEN 12814-2:2019) has been prepared by Technical Committee CEN/TC 249 “Plastics”,

In comparison with the previous edition, the following technical modifications have been made:

— a new annex (Annex A), describing the tensile test specimen geometry for overlap joints, has been

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and

the conditions for performing the tensile test in order to determine the short-term tensile welding factor.

A tensile test may be used in conjunction with other tests (e.g. bend, tensile creep, macro) to assess the

The test is applicable to welded assemblies made from thermoplastics materials filled or unfilled, but not

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

EN ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles (ISO 527-1)

ISO 5893, Rubber and plastics test equipment — Tensile, flexural and compression types (constant rate of

EN 13100-1, Non destructive testing of welded joints of thermoplastics semi-finished products — Part 1:

For the purposes of this document, the symbols and designations given in Table 1 apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses: