SIST EN 300 019-2-1 V2.3.1:2018

SLOVENSKI STANDARD
SIST EN 300 019-2-1 V2.3.1:2018
01-februar-2018
2NROMVNLLQåHQLULQJ((2NROMVNLSRJRMLLQSUHVNXVLYSOLYRYRNROMDQD
WHOHNRPXQLNDFLMVNRRSUHPRGHO6SHFLILNDFLMDSUHVNXVRYYSOLYRYRNROMD
6NODGLãþHQMH

Environmental Engineering (EE) - Environmental conditions and environmental tests for

telecommunications equipment - Part 2-1: Specification of environmental tests - Storage

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

If you find errors in the present document, please send your comment to one of the following services:

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

The content of the PDF version shall not be modified without the written authorization of ETSI.

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and

GSM® and the GSM logo are trademarks registered and owned by the GSM Association.

Intellectual Property Rights ................................................................................................................................ 4

Foreword ............................................................................................................................................................. 4

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions ................................................................................................................................................ 7

4 Environmental test specifications ............................................................................................................. 7

4.0 General ............................................................................................................................................................... 7

4.1 Equipment setup and configuration .................................................................................................................... 7

4.2 Performance criteria ........................................................................................................................................... 7

4.3 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations ................................... 8

4.4 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations ..................................... 11

4.5 Specification T 1.3: Non-weatherprotected storage locations and T 1.3 E: Non-weatherprotected storage

locations - extended .......................................................................................................................................... 14

Annex A (informative): Bibliography ................................................................................................... 21

History .............................................................................................................................................................. 22

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).

The present document is part 2, sub-part 1 of a multi-part deliverable covering the environmental conditions and

Part 1 specifies different standardized environmental classes covering climatic and biological conditions, chemically

and mechanically active substances and mechanical conditions during storage, transportation and in use.

Part 2 specifies the recommended test severities and test methods for the different environmental classes.

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

The present document specifies test severities and methods for verification of the required resistibility of equipment

The tests defined in the present document apply to storage of equipment covering the environmental conditions stated in

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

Referenced documents which are not found to be publicly available in the expected location might be found at

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 300 019-1-1 (2014): "Environmental Engineering (EE); Environmental conditions and

environmental tests for telecommunications equipment; Part 1-1: Classification of environmental

[4] IEC 60068-2-1:2007: "Environmental testing - Part 2-1: Tests - Test A: Cold".

[5] IEC 60068-2-2:2007: "Environmental testing - Part 2-2: Tests - Test B: Dry heat".

[6] IEC 60068-2-6:2007: "Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)".

[7] IEC 60068-2-14:2009: "Environmental testing - Part 2-14: Tests - Test N: Change of temperature".

[8] IEC 60068-2-18:2017: "Environmental testing - Part 2-18: Tests - Test R and guidance: Water".

[9] IEC 60068-2-27:2008: "Environmental testing. Part 2-27: Tests - Test Ea and guidance: Shock".

[10] IEC 60068-2-30:2005: "Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic

[11] IEC 60068-2-78:2012: "Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady

[12] IEC 60068-2-64:2008: "Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

The following referenced documents are not necessary for the application of the present document but they assist the

[i.1] ETSI EN 300 019-2-0 (2003): "Environmental Engineering (EE); Environmental conditions and

environmental tests for telecommunications equipment; Part 2-0: Specification of environmental

[i.2] IEC 60068-2-68:1994: "Environmental testing - Part 2-68: Tests - Test L: Dust and sand".

[i.3] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and

environmental tests for telecommunications equipment; Part 1-0: Classification of environmental

For the purposes of the present document, the terms and definitions given in ETSI EN 300 019-1-0 [i.3] apply.

The equipment shall be tested in the state in which it is normally stored where this is possible. For example, if the

detailed descriptions of the environmental conditions are given in clauses 4 and 5 of ETSI EN 300 019-1-1 [1].

ETSI EN 300 019-2-0 [i.1] forms a general overview of part 2 of this multi-part deliverable.

If the equipment is normally stored in a packed state then it shall be tested in its packaging.

The equipment shall be tested in the state in which it is normally stored where this is possible. For example, if the

equipment is stored in a packed state, then it shall be tested in its packaging. If the equipment can be stored both with

and without its packaging it is necessary to perform tests for both configurations. For some tests and equipment, the test

may be more severe for the packaged rather than the unpacked equipment. For example, for an equipment in a sealed

The following performance criterion A shall apply in the tests defined by the present document.

The equipment, or piece of equipment, shall be verified before and after the tests. The equipment shall function

according to the manufacturer specifications before and after the test. No electrical or mechanical damages shall be

4.3 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations

The specifications in tables 1 and 2 shall apply to weatherprotected or partially weather-controlled storage locations having partially temperature or humidity control described

Table 1: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - climatic tests

Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

NOTE 1: (Air temperature, high) Two test temperatures are given. The lower temperature shall apply if the equipment is protected against solar radiation.

NOTE 2: The characteristic severity value is considered to have insignificant effect on the equipment and therefore no test is required.

NOTE 3: (Humidity, relative high) These severities are the nearest IEC test temperature values, which according to the climatogram can be achieved in the relative

humidity given in the table. This test is recommended for unpacked equipment only.

NOTE 4: This characteristic severity corresponds to the high value of relative humidity and small temperature variation within the equipment and is considered to be

covered by test IEC 60068-2-78 [11] Test Cab. Therefore, no additional tests are required.

NOTE 5: This effect is considered to be partly included in test IEC 60068-2-78 [11] Test Cab and/or test IEC 60068-2-30 [10] Test Db. Therefore, no additional tests

NOTE 6: (Air pressure, low and high) No test is required at equipment level or on sub-assemblies of it, because the effect of air pressure is evaluated at the

NOTE 7: The characteristic severity value is considered to have insignificant effect on the equipment in storage conditions and furthermore there is no IEC test method

NOTE 8: (Radiation, solar, heat)The heating effect of solar radiation is included in the higher test temperature in IEC 60068-2-2 [5] Test Bb as described in note 2.

Photochemical tests can be made separately for components and materials. No test is required in the present document.

NOTE 9: (Chemically active substances) Characteristic severities are mean/maximum values. The characteristic severities should be considered when choosing

NOTE 10: (Mechanically active substances) For mechanically active substances the packaging is supposed to protect the equipment against dust and sand where

needed, therefore no test is required. Furthermore, the levels of dust, both sedimentation and suspension, are far lower than the lowest severity

Table 2: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - mechanical tests

Environmental parameter Environmental Environmental test specification T 1.1: Weatherprotected,

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

NOTE 1: (Vibration, sinusoidal) The characteristic severities are given as peak values. The test severity values defined for this phenomenon are not specified in

NOTE 2: (Vibration, random) ASD (Acceleration Spectral Density). Random vibration testing method may be used instead of the sinusoidal vibration test. The test severity

values are not specified in IEC 60068-2-64 [12]. The maximum test frequency has been reduced because between 100 Hz and 200 Hz the contribution is

NOTE 3: (Shocks) No test is required because this condition is covered by transportation test for packaged equipment and by in-use test for unpackaged equipment.

NOTE 4: (Load) Packaging and/or equipment should be designed taking into account this requirement but no tests are required.

4.4 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations

The specifications in tables 3 and 4 shall apply to weatherprotected or partially weatherprotected storage locations having neither temperature nor humidity control described in

Table 3: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - climatic tests

Environmental parameter Environmental Environmental test specification T1.2: Weatherprotected,

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

Environmental parameter Environmental Environmental test specification T1.2: Weatherprotected,

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

NOTE 1: (Air temperature, high) Two test temperatures are given. The lower temperature shall apply if the equipment is protected against solar radiation.

NOTE 2: The characteristic severity value is considered to have insignificant effect on the equipment and therefore no test is required.

NOTE 3: (Humidity, relative high) These severities are the nearest IEC test temperature values, which according to the climatogram can be achieved in the relative humidity

NOTE 4: This characteristic severity corresponds to the high value of relative humidity and small temperature variation within the equipment and is considered to be

covered by test IEC 60068-2-78 [11] Test Cab. Therefore, no additional tests are required.

NOTE 5: (Humidity, relative, condensation) IEC 60068-2-30 [10] Test Db is recommended with test severities not higher than climatogram limits for this class.

NOTE 6: This effect is considered to be partly included in test IEC 60068-2-78 [11] Test Cab and/or test IEC 60068-2-30 [10] Test Db. Therefore, no additional tests are

NOTE 7: (Air pressure, low and high) No test is required at equipment level or on sub-assemblies of it, because the effect of air pressure is evaluated at the component

NOTE 8: The characteristic severity value is considered to have insignificant effect on the equipment in storage conditions and furthermore there is no IEC test method for

NOTE 9: (Radiation, solar, heat) The heating effect of solar radiation is included in the higher test temperature in IEC 60068-2-2 [5] Test Bb as described in note 2.

Photochemical tests can be made separately for components and materials. No test is required in the present document.

NOTE 10: (Chemically active substances) Characteristic severities are mean/maximum values. The characteristic severities should be considered when choosing

NOTE 11: (Mechanically active substances) For mechanically active substances the packaging is supposed to protect the equipment against dust and sand where needed,

therefore no test is required. Furthermore, the levels of dust, both sedimentation and suspension, are far lower than the lowest severity recommended in

NOTE 12: (Flora and fauna) The characteristic severities should be considered when choosing components and materials but no test is required at the equipment level.

Table 4: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - mechanical tests

Environmental parameter Environmental Environmental test specification T1.2: Weatherprotected

Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Performance Notes

NOTE 1: (Vibration, sinusoidal) The characteristic severities are given as peak values. The test severity values defined for this phenomenon are not specified in

NOTE 2: (Vibration, random) ASD (Acceleration Spectral Density). Random vibration testing method may be used instead of the sinusoidal vibration test. The test severity

values are not specified in IEC 60068-2-64 [12]. The maximum test frequency has been reduced because between 100 Hz and 200 Hz the contribution is insignificant.

NOTE 3: (Shocks) No test is required because this condition is covered by transportation test for packaged equipment and by in-use test for unpackaged equipment.

NOTE 4: (Load) Packaging and/or equipment should be designed taking into account this requirement but no tests are required.