This part of EN 10264 defines cold drawn non alloy steel wire used for the manufacture of:
-   ropes for general applications and lifts;
-   ropes for applications for which there is no specific European Standard.
This part of EN 10264 does not apply to steel wire taken from manufactured ropes.
This part of EN 10264 specifies the following for cold drawn non alloy steel wire for ropes for general applications:
-   dimensional tolerances;
-   mechanical characteristics;
-   requirements relating to the chemical composition of the steel wire;
-   conditions to be satisfied by any coating.
In addition to the requirements of this part of EN 10264, the requirements of EN 10264-1 also apply.

Stahldraht und Drahterzeugnisse - Stahldraht für Seile - Teil 2: Kaltgezogener Draht aus unlegiertem Stahl für Seile für allgemeine Verwendungszwecke

Dieser Teil von EN 10264 legt Anforderungen an kaltgezogenen Draht aus unlegiertem Stahl fest, der für die Herstellung von
-   Seilen für allgemeine Verwendungszwecke und für Aufzüge;
-   Seilen für Anwendungen, für die es keine spezielle Europäische Norm gibt, verwendet wird.
Dieser Teil von EN 10264 gilt nicht für Stahldrähte aus dem fertigen Seil.
Dieser Teil von EN 10264 legt zu folgenden Punkten Anforderungen an kaltgezogenen Draht aus unlegiertem Stahl für Seile für allgemeine Verwendungszwecke fest:
-   Maßtoleranzen;
-   mechanische Eigenschaften;
-   Anforderungen an die chemische Zusammensetzung des Stahldrahts;
-   Anforderungen an Überzüge.
Zusätzlich zu den Anforderungen dieses Teils von EN 10264 gelten auch die Anfor¬derungen nach EN 10264 1.

Fils et produits tréfilés en acier - Fils pour câbles - Partie 2 : Fils écrouis à froid par tréfilage en acier non allié pour câbles d'usages courants

La présente partie de l'EN 10264 définit les fils écrouis à froid par tréfilage en acier non allié utilisés pour la fabrication de :
-   câbles pour usage général et ascenseurs ;
-   câbles pour applications pour lesquelles il n’existe pas de norme européenne particulière.
La présente partie de l'EN 10264 ne s’applique pas aux fils d’acier prélevés sur des câbles fabriqués.
La présente partie de l'EN 10264 spécifie pour les fils écrouis à froid par tréfilage en acier non allié destinés aux câbles d’usage courant :
-   les tolérances dimensionnelles ;
-   les caractéristiques mécaniques ;
-   les exigences relatives à la composition chimique des fils d’acier ;
-   les conditions auxquelles un revêtement éventuel doit satisfaire.
En plus des prescriptions de la présente partie de l'EN 10264, les prescriptions de l’EN 10264-1 sont également applicables.

Jeklena žica in žični izdelki - Jeklena žica za vrvi - 2. del: Hladno vlečena nelegirana jeklena žica za vrvi za splošno uporabo

General Information

Status
Not Published
Public Enquiry End Date
31-Aug-2017
Technical Committee
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
15-Jun-2017
Due Date
02-Nov-2017
Completion Date
01-Sep-2017

RELATIONS

Buy Standard

Standard
oSIST prEN 10264-2:2017
English language
10 pages
sale - 10%
Preview
sale - 10%
Preview

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahldraht und Drahterzeugnisse - Stahldraht für Seile - Teil 2: Kaltgezogener Draht aus unlegiertem Stahl für Seile für allgemeine VerwendungszweckeFils et produits tréfilés en acier - Fils pour câbles - Partie 2 : Fils écrouis à froid par tréfilage en acier non allié pour câbles d'usages courantsSteel wire and wire products - Steel wire for ropes - Part 2: Cold drawn non alloy steel wire for ropes for general applications77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains77.140.45Nelegirana jeklaNon-alloyed steelsICS:Ta slovenski standard je istoveten z:prEN 10264-2oSIST prEN 10264-2:2017en,fr,de01-september-2017oSIST prEN 10264-2:2017SLOVENSKI

STANDARD
oSIST prEN 10264-2:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
DRAFT prEN 10264-2
June
t r s y ICS
y yä s v rä x w Will supersede EN
s r t x væ tã t r s tEnglish Version
Steel wire and wire products æ Steel wire for ropes æ Part

tã Cold drawn non alloy steel wire for ropes for general applications Fils et produits tréfilés en acier æ Fils pour câbles æ Partie

t ã Fils écrouis à froid par tréfilage en acier non allié pour câbles d 5usages courants

Stahldraht und Drahterzeugnisse æ Stahldraht für Seile æ Teil

tã Kaltgezogener Draht aus unlegiertem Stahl für Seile für allgemeine Verwendungszwecke This draft European Standard is submitted to CEN members for enquiryä It has been drawn up by the Technical Committee

If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä

This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä

CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä

Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä

Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels

t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä prEN

s r t x væ tã t r s y EoSIST prEN 10264-2:2017
prEN 10264-2:2017 (E) 2 Contents Page

European foreword ....................................................................................................................................................... 3 1 Scope .................................................................................................................................................................... 4 2 Normative references .................................................................................................................................... 4 3 Product designation ....................................................................................................................................... 4 4 General conditions of manufacture .......................................................................................................... 5 5 Characteristics of wire .................................................................................................................................. 5 5.1 Tensile strength grades ................................................................................................................................ 5 5.2 Requirements for wire characteristics ................................................................................................... 6 6 Test methods ................................................................................................................................................. 10 6.1 General ............................................................................................................................................................. 10 6.2 Measurement of diameter ......................................................................................................................... 10 6.3 Tensile test ..................................................................................................................................................... 10 6.4 Reverse bend test ......................................................................................................................................... 10 6.5 Torsion test .................................................................................................................................................... 10 6.6 Inspection of zinc or Zn95/Al5 alloy coating ..................................................................................... 10

oSIST prEN 10264-2:2017

prEN 10264-2:2017 (E) 3 European foreword This document (prEN 10264-2:2017) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This document is currently submitted to the CEN Enquiry. This document will supersede EN 10264-2:2012. EN 10264, Steel wire and wire products - Steel wire for ropes is made up of the following parts: — Part 1: General requirements — Part 2: Cold drawn non alloy steel wire for ropes for general applications — Part 3: Round and shaped non alloyed steel wire for high duty applications — Part 4: Stainless steel wire This European Standard has been technically revised to incorporate the following changes: a) additional standards have been referenced for manufacturing the drawn wires (see Clause 4); b) the purity of the zinc coating of the drawn wire has been specified according to the relevant EN 1179 (see Clause 4); c) other tensile strength grades than those given in Table 1 have been allowed, subject to an agreement between supplier and user at the time of order (see 5.1); d) other wires than those given in Table 1 have been allowed, subject to an agreement between the customer and the supplier at the time of order (see 5.2); e) new values have been given in Table 2 "Requirements for mechanical characteristics of wire". oSIST prEN 10264-2:2017

prEN 10264-2:2017 (E) 4 1 Scope This part of EN 10264 defines cold drawn non alloy steel wire used for the manufacture of: — ropes for general applications and lifts; — ropes for applications for which there is no specific European Standard. This part of EN 10264 does not apply to steel wire taken from manufactured ropes. This part of EN 10264 specifies the following for cold drawn non alloy steel wire for ropes for general applications: — dimensional tolerances; — mechanical characteristics; — requirements relating to the chemical composition of the steel wire; — conditions to be satisfied by any coating. In addition to the requirements of this part of EN 10264, the requirements of EN 10264-1 also apply. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1179, Zinc and zinc alloys - Primary zinc EN 10218-1, Steel wire and wire products - General - Part 1: Test methods EN 10244-2, Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings EN 10264-1, Steel wire and wire products - Steel wire for ropes - Part 1: General requirements EN ISO 16120-1, Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1) EN ISO 16120-2, Non-alloy steel wire rod for conversion to wire - Part 2: Specific requirements for general purpose wire rod (ISO 16120-2) EN ISO 16120-4, Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4) 3 Product designation The designation of round wire for ropes, covered by this part of EN 10264, shall be based on the nominal diameter (d), surface appearance and tensile strength classification. The abbreviation for the surface finish condition is: — U (uncoated) for bright wire; — A or B for zinc or zinc alloy coating depending on coating class. oSIST prEN 10264-2:2017

prEN 10264-2:2017 (E) 5 A distinction is made between a zinc and a zinc alloy coating by the addition in brackets of “Zn/Al” for the zinc alloy. EXAMPLE 1 Wire for rope for general applications with nominal diameter d = 1,5 mm, surface appearance bright (U), tensile strength grade 1 770 MPa. Designation rope wire EN 10264-2 — 1,5 — U — 1 770 EXAMPLE 2 Wire for rope for general applications with a nominal diameter d = 2,5 mm, zinc coated class A, tensile strength grade 1 370 MPa. Designation rope wire EN 10264-2 — 2,5 — A — 1 370 EXAMPLE 3 Wire for rope for general applications with a nominal diameter d = 1,8 mm, coated with zinc alloy, class B, tensile strength grade 1 770 MPa. Designation rope wire EN 10264-2 — 1,8 — B(Zn/Al) — 1 770 4 General conditions of manufacture The drawn wire shall be manufactured using wire rod in accordance with either EN ISO 16120-1 and EN ISO 16120-2 or EN ISO 16120-1 and EN ISO 16120-4. The finished wire shall show no surface defects or internal defects prejudicial to its use. When specified, drawn wire shall be supplied with zinc coating or Zn95/Al5 coating. Unless otherwise specified, the zinc used for the zinc coating shall have a pu

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.