oSIST prEN ISO 22553-3:2020

SLOVENSKI STANDARD
oSIST prEN ISO 22553-3:2020
01-september-2020
Barve in laki - Nanašanje premazov z elektrodepozicijo - 3. del: Združljivost
elektrodepozicijskih premazov z referenčnim oljem (ISO 22553-3:2019)

Paints and varnishes - Electro-deposition coatings - Part 3: Compatibility of electro-

Beschichtungsstoffe - Elektrotauchlacke - Teil 3: Verträglichkeit von Elektrotauchlacken

Peintures et vernis - Peintures d'électrodéposition - Partie 3: Compatibilité des peintures

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

5 Apparatus and materials.............................................................................................................................................................................. 2

6 Reagents ........................................................................................................................................................................................................................ 3

7 Test panels .................................................................................................................................................................................................................. 3

8 Number of determinations ........................................................................................................................................................................ 3

9 Procedure..................................................................................................................................................................................................................... 3

9.1 Blank test ..................................................................................................................................................................................................... 3

9.2 Testing with reference oil as surface active agent .................................................................................................... 3

10 Evaluation .................................................................................................................................................................................................................... 4

11 Precision ....................................................................................................................................................................................................................... 4

12 Test report ................................................................................................................................................................................................................... 4

Bibliography ................................................................................................................................................................................................................................ 5

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

Any trade name used in this document is information given for the convenience of users and does not

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso

This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee

Any feedback or questions on this document should be directed to the user’s national standards body. A

In practice, surface-reactive substances often contaminate the electro-deposition coating material

inside the tank. These contaminants could be materials that are used in downstream production

processes, e.g. forming additives, corrosion protection oils and chain lubricants.

These surface-active substances can lead to surface defects in the e-coat and/or subsequent coats.

Test methods for the determination of the compatibility of electro-deposition coating materials with

liquid, paste-like and solid foreign substances, which influence the properties of the electro-deposition