The present document specifies technical characteristics and methods of measurements for digital terrestrial television
broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2
signals.
Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or
automotive reception are not covered by the present document.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz
bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,
amplifiers, etc.) are not addressed.
There are country specific variations of frequency usage for digital terrestrial television reception and other users such
as mobile broadband.
The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration
used by the test in question. The applicable tests are summarized in annex E, table E.1.

TV sprejemniki digitalne prizemne radiodifuzije - Harmonizirani standard za dostop do radijskega spektra

General Information

Status
Published
Public Enquiry End Date
22-Sep-2020
Publication Date
05-Nov-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Oct-2020
Due Date
10-Dec-2020
Completion Date
06-Nov-2020

Buy Standard

Standard
SIST EN 303 340 V1.2.1:2020
English language
37 pages
sales 10% off
Preview
sales 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 303 340 V1.2.1 (2020-09) - <empty>
English language
37 pages
sales 15% off
Preview
sales 15% off
Preview
Draft
oSIST prEN 303 340 V1.2.0:2020
English language
36 pages
sales 10% off
Preview
sales 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 303 340 V1.2.0 (2020-06) - Digital Terrestrial TV Broadcast Receivers; Harmonised Standard for access to radio spectrum
English language
36 pages
sales 15% off
Preview
sales 15% off
Preview

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 303 340 V1.2.1:2020
01-december-2020

TV sprejemniki digitalne prizemne radiodifuzije - Harmonizirani standard za dostop

do radijskega spektra

Digital Terrestrial TV Broadcast Receivers - Harmonised Standard for access to radio

spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 340 V1.2.1 (2020-09)
ICS:
33.160.25 Televizijski sprejemniki Television receivers
SIST EN 303 340 V1.2.1:2020 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 303 340 V1.2.1:2020
---------------------- Page: 2 ----------------------
SIST EN 303 340 V1.2.1:2020
ETSI EN 303 340 V1.2.1 (2020-09)
HARMONISED EUROPEAN STANDARD
Digital Terrestrial TV Broadcast Receivers;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
SIST EN 303 340 V1.2.1:2020
2 ETSI EN 303 340 V1.2.1 (2020-09)
Reference
REN/ERM-TG17-32
Keywords
broadcast, digital, harmonised standard, radio,
receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 340 V1.2.1:2020
3 ETSI EN 303 340 V1.2.1 (2020-09)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 6

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 7

3 Definition of terms, symbols and abbreviations ....................................................................................... 8

3.1 Terms .................................................................................................................................................................. 8

3.2 Symbols .............................................................................................................................................................. 9

3.3 Abbreviations ................................................................................................................................................... 10

4 Technical requirements specifications ................................................................................................... 11

4.1 Environmental profile ....................................................................................................................................... 11

4.2 Conformance requirements .............................................................................................................................. 11

4.2.1 DVB-T and DVB-T2 configurations for testing ......................................................................................... 11

4.2.1.1 Modulation Parameters ......................................................................................................................... 11

4.2.1.2 Receiver Configuration ......................................................................................................................... 12

4.2.2 Interference and wanted test signals ........................................................................................................... 12

4.2.3 Sensitivity ................................................................................................................................................... 12

4.2.3.1 Definition .............................................................................................................................................. 12

4.2.3.2 Method of Measurement ....................................................................................................................... 12

4.2.3.2.1 Test arrangement description ........................................................................................................... 12

4.2.3.2.2 Test procedure ................................................................................................................................. 13

4.2.3.3 Limits .................................................................................................................................................... 13

4.2.4 Adjacent channel selectivity ....................................................................................................................... 14

4.2.4.1 Definition .............................................................................................................................................. 14

4.2.4.2 Method of Measurement ....................................................................................................................... 14

4.2.4.2.1 Test arrangement description ........................................................................................................... 14

4.2.4.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 14

4.2.4.2.3 Test procedure ................................................................................................................................. 14

4.2.4.3 Limits .................................................................................................................................................... 16

4.2.5 Blocking ...................................................................................................................................................... 17

4.2.5.1 Definition .............................................................................................................................................. 17

4.2.5.2 Method of Measurement ....................................................................................................................... 17

4.2.5.2.1 Test arrangement description ........................................................................................................... 17

4.2.5.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 17

4.2.5.2.3 Test procedure ................................................................................................................................. 17

4.2.5.3 Limits .................................................................................................................................................... 17

4.2.6 Overloading ................................................................................................................................................ 18

4.2.6.1 Definition .............................................................................................................................................. 18

4.2.6.2 Method of Measurement ....................................................................................................................... 18

4.2.6.2.1 Test arrangement description ........................................................................................................... 18

4.2.6.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 18

4.2.6.2.3 Test procedure ................................................................................................................................. 18

4.2.6.3 Limits .................................................................................................................................................... 19

5 Testing for compliance with technical requirements .............................................................................. 19

5.1 Environmental conditions for testing ............................................................................................................... 19

5.2 Void .................................................................................................................................................................. 19

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 20

Annex B (informative): Summary of study work ................................................................................ 21

ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 340 V1.2.1:2020
4 ETSI EN 303 340 V1.2.1 (2020-09)

B.1 Overview ................................................................................................................................................ 21

B.2 Selection of interferer waveforms .......................................................................................................... 21

B.2.1 UE waveform ................................................................................................................................................... 21

B.2.2 BS waveforms .................................................................................................................................................. 22

B.3 Reception conditions for LTE UE 700 MHz interference ...................................................................... 24

B.3.1 Calculation of maximum coupling gain ........................................................................................................... 24

B.3.2 Calculation of maximum received UE interference power .............................................................................. 25

B.4 Choice of BS interference power in receiver tests ................................................................................. 25

Annex C (informative): Measurement records .................................................................................... 26

Annex D (informative): Additional information to assist measurements .......................................... 28

D.1 Optional elements of the test arrangement ............................................................................................. 28

D.2 Instrument settings for measuring the power of bursty interference signals .......................................... 28

D.3 Improving ACLR ................................................................................................................................... 28

D.4 Measuring ACLR ................................................................................................................................... 29

Annex E (normative): Applicable tests .............................................................................................. 30

E.1 Applicable tests for different receiver variants ...................................................................................... 30

Annex F (normative): Requirements for the interfering signal minimum ACLR ......................... 32

Annex G (informative): Justification of omitted receiver parameters ............................................... 33

G.1 Receiver parameters omitted .................................................................................................................. 33

G.1.1 Co-channel rejection......................................................................................................................................... 33

G.1.2 Spurious response rejection .............................................................................................................................. 33

G.1.3 Intermodulation ................................................................................................................................................ 33

G.1.3.0 General ........................................................................................................................................................ 33

G.1.3.1 Second order intermodulation ..................................................................................................................... 34

G.1.3.2 Third order intermodulation ........................................................................................................................ 34

G.1.4 Dynamic range ................................................................................................................................................. 34

G.1.5 Reciprocal mixing ............................................................................................................................................ 34

G.1.6 Desensitisation ................................................................................................................................................. 35

Annex H (informative): Change History .............................................................................................. 36

History .............................................................................................................................................................. 37

ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 340 V1.2.1:2020
5 ETSI EN 303 340 V1.2.1 (2020-09)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.3].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document has a number of interference test data files that are contained in archive

en_303340v010201p0.zip which accompanies the present document.
National transposition dates
Date of adoption of this EN: 23 September 2020
Date of latest announcement of this EN (doa): 31 December 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2021
Date of withdrawal of any conflicting National Standard (dow): 30 June 2022
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 340 V1.2.1:2020
6 ETSI EN 303 340 V1.2.1 (2020-09)
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 340 V1.2.1:2020
7 ETSI EN 303 340 V1.2.1 (2020-09)
1 Scope

The present document specifies technical characteristics and methods of measurements for digital terrestrial television

broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2

signals.

Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or

automotive reception are not covered by the present document.

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive

2014/53/EU [i.3] is given in annex A.

The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz

bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,

amplifiers, etc.) are not addressed.
Table 1: Broadcast frequency bands
Broadcast frequency bands
VHF III
UHF IV and V

There are country specific variations of frequency usage for digital terrestrial television reception and other users such

as mobile broadband.

The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration

used by the test in question. The applicable tests are summarized in annex E, table E.1.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

Not applicable.
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.
[i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4".
ETSI
---------------------- Page: 9 ----------------------
SIST EN 303 340 V1.2.1:2020
8 ETSI EN 303 340 V1.2.1 (2020-09)

[i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the

Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals".

[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel

coding and modulation for digital terrestrial television".

[i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding

and modulation for a second generation digital terrestrial television broadcasting system

(DVB-T2)".
[i.6] Void.
[i.7] Void.
[i.8] Void.

[i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space

devices under geo-location approach".

[i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television

reference test pattern".

[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.

[i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of

antennas in the reception of television broadcasting".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in

one of the adjacent channels with no active channel in the adjacent channel

NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.

Adjacent Channel Selectivity (ACS): measure of the capability of the receiver to receive a wanted modulated signal

without exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the

wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended

NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation.

NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the

same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU,

CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent

to the measured I/C ratio.

NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.
ETSI
---------------------- Page: 10 ----------------------
SIST EN 303 340 V1.2.1:2020
9 ETSI EN 303 340 V1.2.1 (2020-09)

blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without

exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the

spurious responses or of the adjacent channels

NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation.

NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver

sensitivity level plus 6 dB.

broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator

broadcast receiver tuner port: DTT receiver tuner RF input connector

licensed power: highest rms power of the active portions of the signal measured over a specific time period

NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in

the present document. Typically for cases of LTE interference, this power is measured with a spectrum

analyser in zero span with a gated power measurement function and rms detector over a period equal to

an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding

the appropriate LAPR from table 5.

long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in

the signal power over time such as those due to transmission bursts

NOTE: This can be measured on an average power meter with an input filter time constant set high enough to

average out fluctuations in the measured signal power or alternatively using a spectrum analyser with

settings shown in table D.1.

onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds

radio equipment: product or relevant component thereof capable of communication by means of the emission and/or

reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication

NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast

receiver comprising of at least a tuner and demodulator.

receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to

discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong

non-linear behaviour

NOTE 1: In the present document the overload level is determined by the onset of picture degradation.

NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail

immediately depending on the receiver and interference characteristics.

sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or

field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output

performance which depends on this input signal level

NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation.

3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Wanted signal
G Coupling Gain
I Interferer signal
I Licensed power
lic
I Long term rms power
rms
P Received UE interference power
RX_UE
P UE transmitted power
ETSI
---------------------- Page: 11 ----------------------
SIST EN 303 340 V1.2.1:2020
10 ETSI EN 303 340 V1.2.1 (2020-09)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
256-QAM 256-ary Quadrature Amplitude Modulation
64-QAM 64-ary Quadrature Amplitude Modulation
ACE Active Constellation Extension
ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AGC Automatic Gain Control
AWGN Additive White Gaussian Noise
BER Bit Error Ratio
BS Base Station for mobile communications
CEPT European Conference of Postal and Telecommunications administrations
DTG UK Digital TV Group
DTT Digital Terrestrial Television
DVB-T Digital Video Broadcast Terrestrial - first generation
NOTE: See ETSI EN 300 744 [i.4].
DVB-T2 Digital Video Broadcast Terrestrial - second generation
NOTE: See ETSI EN 302 755 [i.5].
EFTA European Free Trade Association
FEC Forward Error Correction
FEF Future Extension Frame
FFT Fast Fourier Transform
HEM High Efficiency Mode
ISSY Input Stream SYnchronizer
LAPR Licensed to Average Power Ratio
NOTE: This is the ratio of the licensed power (descri
...

ETSI EN 303 340 V1.2.1 (2020-09)
HARMONISED EUROPEAN STANDARD
Digital Terrestrial TV Broadcast Receivers;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 303 340 V1.2.1 (2020-09)
Reference
REN/ERM-TG17-32
Keywords
broadcast, digital, harmonised standard, radio,
receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 340 V1.2.1 (2020-09)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 6

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 7

3 Definition of terms, symbols and abbreviations ....................................................................................... 8

3.1 Terms .................................................................................................................................................................. 8

3.2 Symbols .............................................................................................................................................................. 9

3.3 Abbreviations ................................................................................................................................................... 10

4 Technical requirements specifications ................................................................................................... 11

4.1 Environmental profile ....................................................................................................................................... 11

4.2 Conformance requirements .............................................................................................................................. 11

4.2.1 DVB-T and DVB-T2 configurations for testing ......................................................................................... 11

4.2.1.1 Modulation Parameters ......................................................................................................................... 11

4.2.1.2 Receiver Configuration ......................................................................................................................... 12

4.2.2 Interference and wanted test signals ........................................................................................................... 12

4.2.3 Sensitivity ................................................................................................................................................... 12

4.2.3.1 Definition .............................................................................................................................................. 12

4.2.3.2 Method of Measurement ....................................................................................................................... 12

4.2.3.2.1 Test arrangement description ........................................................................................................... 12

4.2.3.2.2 Test procedure ................................................................................................................................. 13

4.2.3.3 Limits .................................................................................................................................................... 13

4.2.4 Adjacent channel selectivity ....................................................................................................................... 14

4.2.4.1 Definition .............................................................................................................................................. 14

4.2.4.2 Method of Measurement ....................................................................................................................... 14

4.2.4.2.1 Test arrangement description ........................................................................................................... 14

4.2.4.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 14

4.2.4.2.3 Test procedure ................................................................................................................................. 14

4.2.4.3 Limits .................................................................................................................................................... 16

4.2.5 Blocking ...................................................................................................................................................... 17

4.2.5.1 Definition .............................................................................................................................................. 17

4.2.5.2 Method of Measurement ....................................................................................................................... 17

4.2.5.2.1 Test arrangement description ........................................................................................................... 17

4.2.5.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 17

4.2.5.2.3 Test procedure ................................................................................................................................. 17

4.2.5.3 Limits .................................................................................................................................................... 17

4.2.6 Overloading ................................................................................................................................................ 18

4.2.6.1 Definition .............................................................................................................................................. 18

4.2.6.2 Method of Measurement ....................................................................................................................... 18

4.2.6.2.1 Test arrangement description ........................................................................................................... 18

4.2.6.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 18

4.2.6.2.3 Test procedure ................................................................................................................................. 18

4.2.6.3 Limits .................................................................................................................................................... 19

5 Testing for compliance with technical requirements .............................................................................. 19

5.1 Environmental conditions for testing ............................................................................................................... 19

5.2 Void .................................................................................................................................................................. 19

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 20

Annex B (informative): Summary of study work ................................................................................ 21

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 340 V1.2.1 (2020-09)

B.1 Overview ................................................................................................................................................ 21

B.2 Selection of interferer waveforms .......................................................................................................... 21

B.2.1 UE waveform ................................................................................................................................................... 21

B.2.2 BS waveforms .................................................................................................................................................. 22

B.3 Reception conditions for LTE UE 700 MHz interference ...................................................................... 24

B.3.1 Calculation of maximum coupling gain ........................................................................................................... 24

B.3.2 Calculation of maximum received UE interference power .............................................................................. 25

B.4 Choice of BS interference power in receiver tests ................................................................................. 25

Annex C (informative): Measurement records .................................................................................... 26

Annex D (informative): Additional information to assist measurements .......................................... 28

D.1 Optional elements of the test arrangement ............................................................................................. 28

D.2 Instrument settings for measuring the power of bursty interference signals .......................................... 28

D.3 Improving ACLR ................................................................................................................................... 28

D.4 Measuring ACLR ................................................................................................................................... 29

Annex E (normative): Applicable tests .............................................................................................. 30

E.1 Applicable tests for different receiver variants ...................................................................................... 30

Annex F (normative): Requirements for the interfering signal minimum ACLR ......................... 32

Annex G (informative): Justification of omitted receiver parameters ............................................... 33

G.1 Receiver parameters omitted .................................................................................................................. 33

G.1.1 Co-channel rejection......................................................................................................................................... 33

G.1.2 Spurious response rejection .............................................................................................................................. 33

G.1.3 Intermodulation ................................................................................................................................................ 33

G.1.3.0 General ........................................................................................................................................................ 33

G.1.3.1 Second order intermodulation ..................................................................................................................... 34

G.1.3.2 Third order intermodulation ........................................................................................................................ 34

G.1.4 Dynamic range ................................................................................................................................................. 34

G.1.5 Reciprocal mixing ............................................................................................................................................ 34

G.1.6 Desensitisation ................................................................................................................................................. 35

Annex H (informative): Change History .............................................................................................. 36

History .............................................................................................................................................................. 37

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 340 V1.2.1 (2020-09)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.3].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document has a number of interference test data files that are contained in archive

en_303340v010201p0.zip which accompanies the present document.
National transposition dates
Date of adoption of this EN: 23 September 2020
Date of latest announcement of this EN (doa): 31 December 2020
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2021
Date of withdrawal of any conflicting National Standard (dow): 30 June 2022
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 340 V1.2.1 (2020-09)
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 340 V1.2.1 (2020-09)
1 Scope

The present document specifies technical characteristics and methods of measurements for digital terrestrial television

broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2

signals.

Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or

automotive reception are not covered by the present document.

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive

2014/53/EU [i.3] is given in annex A.

The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz

bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,

amplifiers, etc.) are not addressed.
Table 1: Broadcast frequency bands
Broadcast frequency bands
VHF III
UHF IV and V

There are country specific variations of frequency usage for digital terrestrial television reception and other users such

as mobile broadband.

The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration

used by the test in question. The applicable tests are summarized in annex E, table E.1.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

Not applicable.
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.
[i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 340 V1.2.1 (2020-09)

[i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the

Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals".

[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel

coding and modulation for digital terrestrial television".

[i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding

and modulation for a second generation digital terrestrial television broadcasting system

(DVB-T2)".
[i.6] Void.
[i.7] Void.
[i.8] Void.

[i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space

devices under geo-location approach".

[i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television

reference test pattern".

[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.

[i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of

antennas in the reception of television broadcasting".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in

one of the adjacent channels with no active channel in the adjacent channel

NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.

Adjacent Channel Selectivity (ACS): measure of the capability of the receiver to receive a wanted modulated signal

without exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the

wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended

NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation.

NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the

same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU,

CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent

to the measured I/C ratio.

NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 303 340 V1.2.1 (2020-09)

blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without

exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the

spurious responses or of the adjacent channels

NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation.

NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver

sensitivity level plus 6 dB.

broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator

broadcast receiver tuner port: DTT receiver tuner RF input connector

licensed power: highest rms power of the active portions of the signal measured over a specific time period

NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in

the present document. Typically for cases of LTE interference, this power is measured with a spectrum

analyser in zero span with a gated power measurement function and rms detector over a period equal to

an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding

the appropriate LAPR from table 5.

long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in

the signal power over time such as those due to transmission bursts

NOTE: This can be measured on an average power meter with an input filter time constant set high enough to

average out fluctuations in the measured signal power or alternatively using a spectrum analyser with

settings shown in table D.1.

onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds

radio equipment: product or relevant component thereof capable of communication by means of the emission and/or

reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication

NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast

receiver comprising of at least a tuner and demodulator.

receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to

discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong

non-linear behaviour

NOTE 1: In the present document the overload level is determined by the onset of picture degradation.

NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail

immediately depending on the receiver and interference characteristics.

sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or

field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output

performance which depends on this input signal level

NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation.

3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Wanted signal
G Coupling Gain
I Interferer signal
I Licensed power
lic
I Long term rms power
rms
P Received UE interference power
RX_UE
P UE transmitted power
ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 303 340 V1.2.1 (2020-09)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
256-QAM 256-ary Quadrature Amplitude Modulation
64-QAM 64-ary Quadrature Amplitude Modulation
ACE Active Constellation Extension
ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AGC Automatic Gain Control
AWGN Additive White Gaussian Noise
BER Bit Error Ratio
BS Base Station for mobile communications
CEPT European Conference of Postal and Telecommunications administrations
DTG UK Digital TV Group
DTT Digital Terrestrial Television
DVB-T Digital Video Broadcast Terrestrial - first generation
NOTE: See ETSI EN 300 744 [i.4].
DVB-T2 Digital Video Broadcast Terrestrial - second generation
NOTE: See ETSI EN 302 755 [i.5].
EFTA European Free Trade Association
FEC Forward Error Correction
FEF Future Extension Frame
FFT Fast Fourier Transform
HEM High Efficiency Mode
ISSY Input Stream SYnchronizer
LAPR Licensed to Average Power Ratio

NOTE: This is the ratio of the licensed power (described above) to the long term rms power (described above) of

the signal.
LDPC Low Density Parity Check (codes)
LTE Long Term Evolution
PAPR Peak to Average Power Ratio
PLP Physical Layer Pipe
QAM Quadrature Amplitude Modulation
RF Radio Frequency
SINAD (Signal + Noise + Distortion)/(Noise + Distortion) ratio
SISO Single Input Single Output
NOTE: Meaning one transmitting and one receiving antenna.
TFS Time-Frequency Slicing
UE User Equipment for mobile communications
NOTE: Example handsets, dongles, etc.
UHF Ultra High Frequency
VHF Very High Frequency
ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 303 340 V1.2.1 (2020-09)
4 Technical requirements specifications
4.1 Environmental profile

The technical requirements of the present document apply under the environmental profile for operation of the

equipment, which shall be in accordance with its intended use. The equipment shall comply with all the technical

requirements of the pres
...

SLOVENSKI STANDARD
oSIST prEN 303 340 V1.2.0:2020
01-september-2020

Digitalni prizemni radiodifuzijski sprejemniki - Harmonizirani standard za dostop

do radijskega spektra

Digital Terrestrial TV Broadcast Receivers - Harmonised Standard for access to radio

spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 340 V1.2.0 (2020-06)
ICS:
33.160.25 Televizijski sprejemniki Television receivers
oSIST prEN 303 340 V1.2.0:2020 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 303 340 V1.2.0:2020
---------------------- Page: 2 ----------------------
oSIST prEN 303 340 V1.2.0:2020
Draft ETSI EN 303 340 V1.2.0 (2020-06)
HARMONISED EUROPEAN STANDARD
Digital Terrestrial TV Broadcast Receivers;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 303 340 V1.2.0:2020
2 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Reference
REN/ERM-TG17-32
Keywords
broadcast, digital, harmonised standard, radio,
receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 340 V1.2.0:2020
3 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definition of terms, symbols and abbreviations ....................................................................................... 7

3.1 Terms .................................................................................................................................................................. 7

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 9

4 Technical requirements specifications ................................................................................................... 10

4.1 Environmental profile ....................................................................................................................................... 10

4.2 Conformance requirements .............................................................................................................................. 10

4.2.1 DVB-T and DVB-T2 configurations for testing ......................................................................................... 10

4.2.1.1 Modulation Parameters ......................................................................................................................... 10

4.2.1.2 Receiver Configuration ......................................................................................................................... 11

4.2.2 Interference and wanted test signals ........................................................................................................... 11

4.2.3 Sensitivity ................................................................................................................................................... 11

4.2.3.1 Definition .............................................................................................................................................. 11

4.2.3.2 Method of Measurement ....................................................................................................................... 11

4.2.3.2.1 Test arrangement description ........................................................................................................... 11

4.2.3.2.2 Test procedure ................................................................................................................................. 12

4.2.3.3 Limits .................................................................................................................................................... 12

4.2.4 Adjacent channel selectivity ....................................................................................................................... 13

4.2.4.1 Definition .............................................................................................................................................. 13

4.2.4.2 Method of Measurement ....................................................................................................................... 13

4.2.4.2.1 Test arrangement description ........................................................................................................... 13

4.2.4.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 13

4.2.4.2.3 Test procedure ................................................................................................................................. 13

4.2.4.3 Limits .................................................................................................................................................... 15

4.2.5 Blocking ...................................................................................................................................................... 16

4.2.5.1 Definition .............................................................................................................................................. 16

4.2.5.2 Method of Measurement ....................................................................................................................... 16

4.2.5.2.1 Test arrangement description ........................................................................................................... 16

4.2.5.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 16

4.2.5.2.3 Test procedure ................................................................................................................................. 16

4.2.5.3 Limits .................................................................................................................................................... 16

4.2.6 Overloading ................................................................................................................................................ 17

4.2.6.1 Definition .............................................................................................................................................. 17

4.2.6.2 Method of Measurement ....................................................................................................................... 17

4.2.6.2.1 Test arrangement description ........................................................................................................... 17

4.2.6.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 17

4.2.6.2.3 Test procedure ................................................................................................................................. 17

4.2.6.3 Limits .................................................................................................................................................... 18

5 Testing for compliance with technical requirements .............................................................................. 18

5.1 Environmental conditions for testing ............................................................................................................... 18

5.2 Void .................................................................................................................................................................. 18

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 19

Annex B (informative): Summary of study work ................................................................................ 20

ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 340 V1.2.0:2020
4 Draft ETSI EN 303 340 V1.2.0 (2020-06)

B.1 Overview ................................................................................................................................................ 20

B.2 Selection of interferer waveforms .......................................................................................................... 20

B.2.1 UE waveform ................................................................................................................................................... 20

B.2.2 BS waveforms .................................................................................................................................................. 21

B.3 Reception conditions for LTE UE 700 MHz interference ...................................................................... 23

B.3.1 Calculation of maximum coupling gain ........................................................................................................... 23

B.3.2 Calculation of maximum received UE interference power .............................................................................. 24

B.4 Choice of BS interference power in receiver tests ................................................................................. 24

Annex C (informative): Measurement records .................................................................................... 25

Annex D (informative): Additional information to assist measurements .......................................... 27

D.1 Optional elements of the test arrangement ............................................................................................. 27

D.2 Instrument settings for measuring the power of bursty interference signals .......................................... 27

D.3 Improving ACLR ................................................................................................................................... 27

D.4 Measuring ACLR ................................................................................................................................... 28

Annex E (normative): Applicable tests .............................................................................................. 29

E.1 Applicable tests for different receiver variants ...................................................................................... 29

Annex F (normative): Requirements for the interfering signal minimum ACLR ......................... 31

Annex G (informative): Justification of omitted receiver parameters ............................................... 32

G.1 Receiver parameters omitted .................................................................................................................. 32

G.1.1 Co-channel rejection......................................................................................................................................... 32

G.1.2 Spurious response rejection .............................................................................................................................. 32

G.1.3 Intermodulation ................................................................................................................................................ 32

G.1.3.0 General ........................................................................................................................................................ 32

G.1.3.1 Second order intermodulation ..................................................................................................................... 33

G.1.3.2 Third order intermodulation ........................................................................................................................ 33

G.1.4 Dynamic range ................................................................................................................................................. 33

G.1.5 Reciprocal mixing ............................................................................................................................................ 33

G.1.6 Desensitisation ................................................................................................................................................. 34

Annex H (informative): Change History .............................................................................................. 35

History .............................................................................................................................................................. 36

ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 340 V1.2.0:2020
5 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.3].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document has a number of interference test data files that are contained in archive

en_303340v010200a0.zip which accompanies the present document.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 340 V1.2.0:2020
6 Draft ETSI EN 303 340 V1.2.0 (2020-06)
1 Scope

The present document specifies technical characteristics and methods of measurements for digital terrestrial television

broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2

signals.

Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or

automotive reception are not covered by the present document.

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive

2014/53/EU [i.3] is given in annex A.

The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz

bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,

amplifiers, etc.) are not addressed.
Table 1: Broadcast frequency bands
Broadcast frequency bands
VHF III
UHF IV and V

There are country specific variations of frequency usage for digital terrestrial television reception and other users such

as mobile broadband.

The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration

used by the test in question. The applicable tests are summarized in annex E, table E.1.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

Not applicable.
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.
[i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4".
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 340 V1.2.0:2020
7 Draft ETSI EN 303 340 V1.2.0 (2020-06)

[i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the

Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals".

[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel

coding and modulation for digital terrestrial television".

[i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding

and modulation for a second generation digital terrestrial television broadcasting system

(DVB-T2)".
[i.6] Void.
[i.7] Void.
[i.8] Void.

[i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space

devices under geo-location approach".

[i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television

reference test pattern".

[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.

[i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of

antennas in the reception of television broadcasting".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in

one of the adjacent channels with no active channel in the adjacent channel

NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.

Adjacent Channel Selectivity (ACS): measure of the capability of the receiver to receive a wanted modulated signal

without exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the

wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended

NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation.

NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the

same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU,

CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent

to the measured I/C ratio.

NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 303 340 V1.2.0:2020
8 Draft ETSI EN 303 340 V1.2.0 (2020-06)

blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without

exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the

spurious responses or of the adjacent channels

NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation.

NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver

sensitivity level plus 6 dB.

broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator

broadcast receiver tuner port: DTT receiver tuner RF input connector

licensed power: highest rms power of the active portions of the signal measured over a specific time period

NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in

the present document. Typically for cases of LTE interference, this power is measured with a spectrum

analyser in zero span with a gated power measurement function and rms detector over a period equal to

an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding

the appropriate LAPR from table 5.

long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in

the signal power over time such as those due to transmission bursts

NOTE: This can be measured on an average power meter with an input filter time constant set high enough to

average out fluctuations in the measured signal power or alternatively using a spectrum analyser with

settings shown in table D.1.

onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds

radio equipment: product or relevant component thereof capable of communication by means of the emission and/or

reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication

NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast

receiver comprising of at least a tuner and demodulator.

receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to

discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong

non-linear behaviour

NOTE 1: In the present document the overload level is determined by the onset of picture degradation.

NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail

immediately depending on the receiver and interference characteristics.

sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or

field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output

performance which depends on this input signal level

NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation.

3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Wanted signal
G Coupling Gain
I Interferer signal
I Licensed power
lic
I Long term rms power
rms
P Received UE interference power
RX_UE
P UE transmitted power
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 303 340 V1.2.0:2020
9 Draft ETSI EN 303 340 V1.2.0 (2020-06)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
256-QAM 256-ary Quadrature Amplitude Modulation
64-QAM 64-ary Quadrature Amplitude Modulation
ACE Active Constellation Extension
ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AGC Automatic Gain Control
AWGN Additive White Gaussian Noise
BER Bit Error Ratio
BS Base Station for mobile communications
CEPT European Conference of Postal and Telecommunications administrations
DTG UK Digital TV Group
DTT Digital Terrestrial Television
DVB-T Digital Video Broadcast Terrestrial - first generation
NOTE: See ETSI EN 300 744 [i.4].
DVB-T2 Digital Video Broadcast Terrestrial - second generation
NOTE: See ETSI EN 302 755 [i.5].
EFTA European Free Trade Association
FEC Forward Error Correction
FEF Future Extension Frame
FFT Fast Fourier Transform
HEM High Efficiency Mode
ISSY Input Stream SYnchronizer
LAPR Licensed to Average Power Rat
...

Draft ETSI EN 303 340 V1.2.0 (2020-06)
HARMONISED EUROPEAN STANDARD
Digital Terrestrial TV Broadcast Receivers;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Reference
REN/ERM-TG17-32
Keywords
broadcast, digital, harmonised standard, radio,
receiver
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definition of terms, symbols and abbreviations ....................................................................................... 7

3.1 Terms .................................................................................................................................................................. 7

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 9

4 Technical requirements specifications ................................................................................................... 10

4.1 Environmental profile ....................................................................................................................................... 10

4.2 Conformance requirements .............................................................................................................................. 10

4.2.1 DVB-T and DVB-T2 configurations for testing ......................................................................................... 10

4.2.1.1 Modulation Parameters ......................................................................................................................... 10

4.2.1.2 Receiver Configuration ......................................................................................................................... 11

4.2.2 Interference and wanted test signals ........................................................................................................... 11

4.2.3 Sensitivity ................................................................................................................................................... 11

4.2.3.1 Definition .............................................................................................................................................. 11

4.2.3.2 Method of Measurement ....................................................................................................................... 11

4.2.3.2.1 Test arrangement description ........................................................................................................... 11

4.2.3.2.2 Test procedure ................................................................................................................................. 12

4.2.3.3 Limits .................................................................................................................................................... 12

4.2.4 Adjacent channel selectivity ....................................................................................................................... 13

4.2.4.1 Definition .............................................................................................................................................. 13

4.2.4.2 Method of Measurement ....................................................................................................................... 13

4.2.4.2.1 Test arrangement description ........................................................................................................... 13

4.2.4.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 13

4.2.4.2.3 Test procedure ................................................................................................................................. 13

4.2.4.3 Limits .................................................................................................................................................... 15

4.2.5 Blocking ...................................................................................................................................................... 16

4.2.5.1 Definition .............................................................................................................................................. 16

4.2.5.2 Method of Measurement ....................................................................................................................... 16

4.2.5.2.1 Test arrangement description ........................................................................................................... 16

4.2.5.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 16

4.2.5.2.3 Test procedure ................................................................................................................................. 16

4.2.5.3 Limits .................................................................................................................................................... 16

4.2.6 Overloading ................................................................................................................................................ 17

4.2.6.1 Definition .............................................................................................................................................. 17

4.2.6.2 Method of Measurement ....................................................................................................................... 17

4.2.6.2.1 Test arrangement description ........................................................................................................... 17

4.2.6.2.2 Requirements for the ACLR of the interfering signal ..................................................................... 17

4.2.6.2.3 Test procedure ................................................................................................................................. 17

4.2.6.3 Limits .................................................................................................................................................... 18

5 Testing for compliance with technical requirements .............................................................................. 18

5.1 Environmental conditions for testing ............................................................................................................... 18

5.2 Void .................................................................................................................................................................. 18

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 19

Annex B (informative): Summary of study work ................................................................................ 20

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 340 V1.2.0 (2020-06)

B.1 Overview ................................................................................................................................................ 20

B.2 Selection of interferer waveforms .......................................................................................................... 20

B.2.1 UE waveform ................................................................................................................................................... 20

B.2.2 BS waveforms .................................................................................................................................................. 21

B.3 Reception conditions for LTE UE 700 MHz interference ...................................................................... 23

B.3.1 Calculation of maximum coupling gain ........................................................................................................... 23

B.3.2 Calculation of maximum received UE interference power .............................................................................. 24

B.4 Choice of BS interference power in receiver tests ................................................................................. 24

Annex C (informative): Measurement records .................................................................................... 25

Annex D (informative): Additional information to assist measurements .......................................... 27

D.1 Optional elements of the test arrangement ............................................................................................. 27

D.2 Instrument settings for measuring the power of bursty interference signals .......................................... 27

D.3 Improving ACLR ................................................................................................................................... 27

D.4 Measuring ACLR ................................................................................................................................... 28

Annex E (normative): Applicable tests .............................................................................................. 29

E.1 Applicable tests for different receiver variants ...................................................................................... 29

Annex F (normative): Requirements for the interfering signal minimum ACLR ......................... 31

Annex G (informative): Justification of omitted receiver parameters ............................................... 32

G.1 Receiver parameters omitted .................................................................................................................. 32

G.1.1 Co-channel rejection......................................................................................................................................... 32

G.1.2 Spurious response rejection .............................................................................................................................. 32

G.1.3 Intermodulation ................................................................................................................................................ 32

G.1.3.0 General ........................................................................................................................................................ 32

G.1.3.1 Second order intermodulation ..................................................................................................................... 33

G.1.3.2 Third order intermodulation ........................................................................................................................ 33

G.1.4 Dynamic range ................................................................................................................................................. 33

G.1.5 Reciprocal mixing ............................................................................................................................................ 33

G.1.6 Desensitisation ................................................................................................................................................. 34

Annex H (informative): Change History .............................................................................................. 35

History .............................................................................................................................................................. 36

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 340 V1.2.0 (2020-06)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.11] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.3].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document has a number of interference test data files that are contained in archive

en_303340v010200a0.zip which accompanies the present document.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 340 V1.2.0 (2020-06)
1 Scope

The present document specifies technical characteristics and methods of measurements for digital terrestrial television

broadcast receivers fitted with an external antenna input (tuner port) capable of receiving DVB-T and/or DVB-T2

signals.

Receivers without external antenna connectors, receivers with diversity, and receivers intended for mobile or

automotive reception are not covered by the present document.

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive

2014/53/EU [i.3] is given in annex A.

The present document includes considerations of interference from LTE transmissions in the 700 MHz and 800 MHz

bands and DTT transmissions in UHF band IV. The requirements of the installation system (antenna, feeder cable,

amplifiers, etc.) are not addressed.
Table 1: Broadcast frequency bands
Broadcast frequency bands
VHF III
UHF IV and V

There are country specific variations of frequency usage for digital terrestrial television reception and other users such

as mobile broadband.

The tests in the present document only apply if the DTT broadcast receiver supports the wanted signal configuration

used by the test in question. The applicable tests are summarized in annex E, table E.1.

2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

Not applicable.
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.
[i.1] Nordig: "NorDig Unified Test Plan for Integrated Receiver Decoders v2.4".
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 340 V1.2.0 (2020-06)

[i.2] British Broadcasting Corporation and Arqiva, WHP288: "WSD Coexistence Testing at the

Building Research Establishment: An Experimental Validation of Ofcom Regulatory Proposals".

[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.4] ETSI EN 300 744 (V1.6.1): "Digital Video Broadcasting (DVB); Framing structure, channel

coding and modulation for digital terrestrial television".

[i.5] ETSI EN 302 755 (V1.3.1): "Digital Video Broadcasting (DVB); Frame structure channel coding

and modulation for a second generation digital terrestrial television broadcasting system

(DVB-T2)".
[i.6] Void.
[i.7] Void.
[i.8] Void.

[i.9] ECC Report 186 (2013): "Technical and operational requirements for the operation of white space

devices under geo-location approach".

[i.10] Recommendation ITU-R BT.1729 (2005): "Common 16:9 or 4:3 aspect ratio digital television

reference test pattern".

[i.11] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.

[i.12] Recommendation ITU-R BT.419-3 (1990): "Directivity and polarization discrimination of

antennas in the reception of television broadcasting".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

Adjacent Channel Leakage power Ratio (ACLR): ratio of the on-channel transmit power to the power measured in

one of the adjacent channels with no active channel in the adjacent channel

NOTE: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.

Adjacent Channel Selectivity (ACS): measure of the capability of the receiver to receive a wanted modulated signal

without exceeding a given degradation due to the presence of an unwanted signal which differs in frequency from the

wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended

NOTE 1: In the present document adjacent channel selectivity is determined by the onset of picture degradation.

NOTE 2: The interference power I is equal to the licensed power of the interferer. This definition does not have the

same meaning as the term "Adjacent Channel Selectivity" (ACS) used in other organizations such as ITU,

CEPT, and in co-existence studies. The adjacent channel selectivity in the present document is equivalent

to the measured I/C ratio.

NOTE 3: In the present document this definition also applies to an unwanted signal at a specified frequency offset

in a non-adjacent channel.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 340 V1.2.0 (2020-06)

blocking or desensitization: measure of the capability of the receiver to receive a wanted modulated signal without

exceeding a given degradation due to the presence of an unwanted signal at any frequency other than those of the

spurious responses or of the adjacent channels

NOTE 1: In the present document receiver blocking is determined by the onset of picture degradation.

NOTE 2: The wanted signal level in the blocking tests of the present document is set at the specified receiver

sensitivity level plus 6 dB.

broadcast receiver: digital terrestrial television broadcast receiver comprising of at least a tuner and demodulator

broadcast receiver tuner port: DTT receiver tuner RF input connector

licensed power: highest rms power of the active portions of the signal measured over a specific time period

NOTE: In the case of interference power measurements, this is the reference power used for I/C calculations in

the present document. Typically for cases of LTE interference, this power is measured with a spectrum

analyser in zero span with a gated power measurement function and rms detector over a period equal to

an LTE symbol time. Alternatively it can be calculated by measuring the long term rms power and adding

the appropriate LAPR from table 5.

long term rms power: rms power of the signal measured over a period long enough to smooth out any fluctuations in

the signal power over time such as those due to transmission bursts

NOTE: This can be measured on an average power meter with an input filter time constant set high enough to

average out fluctuations in the measured signal power or alternatively using a spectrum analyser with

settings shown in table D.1.

onset of picture degradation: minimum time between successive errors in the displayed video is 15 seconds

radio equipment: product or relevant component thereof capable of communication by means of the emission and/or

reception of radio waves utilizing the spectrum allocated to terrestrial/space radio communication

NOTE: For the purposes of the present document the radio equipment is a digital terrestrial television broadcast

receiver comprising of at least a tuner and demodulator.

receiver overloading: interfering signal level expressed in dBm, above which the receiver begins to lose its ability to

discriminate against interfering signals at frequencies differing from that of the wanted signal due to the onset of strong

non-linear behaviour

NOTE 1: In the present document the overload level is determined by the onset of picture degradation.

NOTE 2: Above the overloading level the receiver will behave in a non-linear way, but does not necessarily fail

immediately depending on the receiver and interference characteristics.

sensitivity: maximum usable sensitivity is defined as the minimum receiver Radio Frequency (RF) input signal level or

field strength able to produce a specified analogue SINAD ratio or Bit Error Ratio (BER), or other specified output

performance which depends on this input signal level

NOTE: In the present document receiver sensitivity is determined by the onset of picture degradation.

3.2 Symbols
For the purposes of the present document, the following symbols apply:
C Wanted signal
G Coupling Gain
I Interferer signal
I Licensed power
lic
I Long term rms power
rms
P Received UE interference power
RX_UE
P UE transmitted power
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 340 V1.2.0 (2020-06)
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
256-QAM 256-ary Quadrature Amplitude Modulation
64-QAM 64-ary Quadrature Amplitude Modulation
ACE Active Constellation Extension
ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AGC Automatic Gain Control
AWGN Additive White Gaussian Noise
BER Bit Error Ratio
BS Base Station for mobile communications
CEPT European Conference of Postal and Telecommunications administrations
DTG UK Digital TV Group
DTT Digital Terrestrial Television
DVB-T Digital Video Broadcast Terrestrial - first generation
NOTE: See ETSI EN 300 744 [i.4].
DVB-T2 Digital Video Broadcast Terrestrial - second generation
NOTE: See ETSI EN 302 755 [i.5].
EFTA European Free Trade Association
FEC Forward Error Correction
FEF Future Extension Frame
FFT Fast Fourier Transform
HEM High Efficiency Mode
ISSY Input Stream SYnchronizer
LAPR Licensed to Average Power Ratio

NOTE: This is the ratio of the licensed power (described above) to the long term rms power (described above) of

the signal.
LDPC Low Density Parity Check (codes)
LTE Long Term Evolution
PAPR Peak to Average Power Ratio
PLP Physical Layer Pipe
QAM Quadrature Amplitude Modulation
RF Radio Frequency
SINAD (Signal + Noise + Distortion)/(Noise + Distortion) ratio
SISO Single Input Single Output
NOTE: Meaning one transmitting and one receiving antenna.
TFS Time-Frequency Slicing
UE User Equipment for mobile communications
NOTE: Example handsets, dongles, etc.
UHF Ultra High Frequency
VHF Very High Frequency
ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 303 340 V1.2.0 (2020-06)
4 Technical requirements specifications
4.1 Environmental profile

The technical requirements of the present document apply under the environmental profile for operation of the

equipment, which shall be in accordance with its intended use. The equip
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.