49.030.20 - Bolts, screws, studs

EN 2575 specifies the characteristics, qualification and acceptance requirements for bolts with MJ threads in heat resisting steel FE-PA2601, for aerospace applications.Classification: 900 MPa1/ 650 °C2.It is applicable whenever referenced.
Details

This European Standard specifies the characteristics, qualification and acceptance requirements for helical coil screw thread inserts. It is applicable whenever referenced.

This document specifies the characteristics of bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 dryfilm coated, for aerospace applications. Classification: 1 100 MPa1/315 °C2. These bolts are intended to be used with washers according to EN 2414 and nuts according to EN 3230.

This document specifies the characteristics of screws, pan head, offset cruciform recess, normal shank, long thread, in alloy steel, cadmium plated.
Classification: 1 100 MPa )/235 °C ).

This European Standard specifies dimensions, tolerances, characteristics and qualification requirements for MORTORQ Spiral Drive Recesses .
[MORTORQ® is the trade name of a product supplied by licensees of the Phillips Screw Company. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by ASD-STAN nor CEN of the product named. Equivalent products may be used if they can be shown to lead to the same results.]

This European standard specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated, for aerospace applications.
Classification: 1 100 MPa /235 °C .

This European standard specifies the characteristics of bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 dryfilm coated, for aerospace applications.
Classification: 1 100 MPa /315 °C .
These bolts are intended to be used with washers according to EN 2414 and nuts according to EN 3230.

This document specifies the technical, qualification and quality assurance requirements for bolts in material FE-PA2601 (A286) of tensile strength class 1 100 MPa at room temperature, maximum test temperature of material 650 °C.
Primarily for aerospace applications it is applicable to such bolts when referenced on the product standard or definition document.

This document specifies the technical, qualification and quality assurance requirements for bolts in material FE-PA2601 (A286) of tensile strength class 1 100 MPa at room temperature, maximum test temperature of material 650 °C.
Primarily for aerospace applications it is applicable to such bolts when referenced on the product standard or definition document.

This European standard specifies dimensions and gauging system for external MORTORQ super bolt
head spiral drive system1.

This European standard specifies dimensions and gauging system for external MORTORQ super bolt
head spiral drive system1.

This European standard specifies the characteristics, qualification and acceptance requirements for
bolts with MJ threads in TI-P64001, for aerospace applications.
Strength class: 1 100 MPa1.
It is applicable whenever referenced.

This document specifies the technical, qualification and quality assurance requirements for sensor based clamp load measurement systems for high tensile bolts and other clamp load sensitive elements. Primarily for aerospace applications, it is applicable to such products when referenced on the product standard or drawing.

This standard specifies the characteristics, qualification and acceptance requirements for bolts with MJ
threads in NI-PH2601.
Classification: 1 275 MPa1/650 °C2.
It is applicable whenever referenced.

This European standard specifies the characteristics, qualification and acceptance requirements for
bolts with MJ threads in TI-P64001, for aerospace applications.
Strength class: 1 100 MPa1.
It is applicable whenever referenced.

This standard specifies the characteristics, qualification and acceptance requirements for bolts with MJ threads in NI-PH2601.
Classification: 1 275 MPa /650 °C .
It is applicable whenever referenced.

This European standard specifies the characteristics, qualification and acceptance requirements for
bolts with MJ threads in NI-PH2601, passivated, for aerospace applications.
Classification: 1 550 MPa1/650 °C2.
It is applicable whenever referenced.

This European standard specifies the characteristics, qualification and acceptance requirements for bolts with MJ threads in NI-PH2601, passivated, for aerospace applications.
Classification: 1 550 MPa1/650 °C2.
It is applicable whenever referenced.

This document specifies the technical, qualification and quality assurance requirements for sensor based clamp load measurement systems for high tensile bolts and other clamp load sensitive elements. Primarily for aerospace applications, it is applicable to such products when referenced on the product standard or drawing.

This European standard specifies the characteristics of inserts, self locking, helical coil, tanged insertion drive, screw thread in NI-PH2801, for aerospace applications.
Maximum test temperature: 350 °C