kSIST FprEN 3077:2020
(Main)Aerospace series - Clamps worm drive - Technical specification
Aerospace series - Clamps worm drive - Technical specification
This document specifies the required characteristics, inspections, test methods, quality assurance, qualification, acceptance and delivery conditions of clamps worm drive designed for use with suitable rubber hoses to form joints in fluid system pipelines.
The clamps worm drive are intended to be used as specified in the product standards.
Luft- und Raumfahrt - Schellen mit Schneckentrieb - Technische Lieferbedingungen
Série aérospatiale - Colliers à vis tangente - Spécification technique
Le présent document spécifie les caractéristiques requises, les contrôles, les méthodes d’essai, l’assurance qualité, la qualification, la réception et les conditions de livraison des colliers à vis tangente conçus pour utilisation avec des tuyauteries en caoutchouc appropriées pour les raccordements de canalisations de systèmes de fluides.
Les colliers à vis tangente sont destinés à être utilisés comme spécifié dans les normes de produits.
Aeronavtika - Cevne objemke - Tehnična specifikacija
General Information
Standards Content (sample)
SLOVENSKI STANDARD
oSIST prEN 3077:2020
01-september-2020
Aeronavtika - Cevne objemke - Tehnična specifikacija
Aerospace series - Clamps worm drive - Technical specification
Luft- und Raumfahrt - Schellen mit Schneckentrieb - Technische Lieferbedingungen
Série aérospatiale - Colliers à vis tangente - Spécification technique
Ta slovenski standard je istoveten z: prEN 3077
ICS:
49.030.99 Drugi vezni elementi Other fasteners
oSIST prEN 3077:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN 3077:2020
---------------------- Page: 2 ----------------------
oSIST prEN 3077:2020
DRAFT
EUROPEAN STANDARD
prEN 3077
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS
English Version
Aerospace series - Clamps worm drive - Technical
specification
Série aérospatiale - Colliers à vis tangente - Luft- und Raumfahrt - Schellen mit Schneckentrieb -
Spécification technique Technische LieferbedingungenThis draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 3077:2020 E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
oSIST prEN 3077:2020
prEN 3077:2020 (E)
Contents Page
European foreword ....................................................................................................................................................... 3
1 Scope .................................................................................................................................................................... 4
2 Normative references .................................................................................................................................... 4
3 Terms and definitions ................................................................................................................................... 4
4 Requirements, inspection and test methods ......................................................................................... 5
5 Quality assurance ............................................................................................................................................ 6
5.1 Approval of manufacturer ........................................................................................................................... 6
5.2 Product qualification ..................................................................................................................................... 6
6 Acceptance conditions ................................................................................................................................... 7
6.1 Manufacturer’s responsibility .................................................................................................................... 7
6.2 Inspections and tests ..................................................................................................................................... 7
7 Packaging ........................................................................................................................................................... 8
8 Acceptance test certificate ........................................................................................................................... 8
Annex A (informative) Evolution sheet ................................................................................................................ 9
Bibliography ................................................................................................................................................................. 10
---------------------- Page: 4 ----------------------oSIST prEN 3077:2020
prEN 3077:2020 (E)
European foreword
This document (prEN 3077:2020) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.This document is currently submitted to the CEN Enquiry.
---------------------- Page: 5 ----------------------
oSIST prEN 3077:2020
prEN 3077:2020 (E)
1 Scope
This document specifies the required characteristics, inspections, test methods, quality assurance,
qualification, acceptance and delivery conditions of clamps worm drive designed for use with suitable
rubber hoses to form joints in fluid system pipelines.The clamps worm drive are intended to be used as specified in the product standards.
2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10204, Metallic products - Types of inspection documentsISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by
acceptance quality limit (AQL) for lot-by-lot inspection3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp— IEC Electropedia: available at http://www.electropedia.org/
3.1
clamp worm drive
band of material fitted with an adjustment device intended for use in conjunction with a suitable hose to
provide a pipe-to-pipe joint3.2
batch
clamps of a particular size and material produced under essentially the same manufacturing condi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.