SIST EN ISO 129-1:2019/oprA1:2020

Technical product documentation (TPD) - Presentation of dimensions and tolerances - Part 1: General principles - Amendment 1 (ISO 129-1:2018/Amd 1:2020)

Technische Produktdokumentation (TPD) - Angabe von Maßen und Toleranzen - Teil 1: Grundlagen - Änderung 1 (ISO 129-1:2018/Amd 1:2020)

Documentation technique de produits - Représentation des dimensions et tolérances - Partie 1: Principes généraux - Amendement 1 (ISO 129-1:2018/Amd 1:2020)

Tehnična dokumentacija izdelkov - Predstavitev dimenzij in toleranc - 1. del: Splošna načela - Dopolnilo 1 (ISO 129-1:2018/Amd 1:2020)

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 129-1:2019/oprA1:2020
01-september-2020
Tehnična dokumentacija proizvodov - Predstavitev dimenzij in toleranc - 1. del:
Splošna načela - Dopolnilo 1 (ISO 129-1:2018/Amd 1:2020)

Technical product documentation (TPD) - Presentation of dimensions and tolerances -

Part 1: General principles - Amendment 1 (ISO 129-1:2018/Amd 1:2020)

Documentation technique de produits - Représentation des dimensions et tolérances -

Partie 1: Principes généraux - Amendement 1 (ISO 129-1:2018/Amd 1:2020)
Ta slovenski standard je istoveten z: EN ISO 129-1:2019/prA1
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
SIST EN ISO 129-1:2019/oprA1:2020 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 129-1:2019/oprA1:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 129-1:2019/oprA1:2020
INTERNATIONAL ISO
STANDARD 129-1
Second edition
2018-02
AMENDMENT 1
2020-03
Technical product documentation
(TPD) — Presentation of dimensions
and tolerances —
Part 1:
General principles
AMENDMENT 1
Documentation technique de produits — Représentation des
dimensions et tolérances —
Partie 1: Principes généraux
AMENDEMENT 1
Reference number
ISO 129-1:2018/Amd.1:2020(E)
ISO 2020
---------------------- Page: 3 ----------------------
SIST EN ISO 129-1:2019/oprA1:2020
ISO 129-1:2018/Amd.1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 129-1:2019/oprA1:2020
ISO 129-1:2018/Amd.1:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established ha
...