ISO/IEC 14443-4:2008/DAmd 6

S(PARAMETERS) clarification

Clarification des S(PARAMETERS)

Standards Content (sample)

DRAFT AMENDMENT
ISO/IEC 14443-4:2008/DAM 6
ISO/IEC JTC 1/SC 17 Secretariat: BSI
Voting begins on:  Voting terminates on:
2016-02-09 2016-05-09
Identification cards — Contactless integrated circuit
cards — Proximity cards —
Part 4:
Transmission protocol
AMENDMENT 6: S(PARAMETERS) clarification

Cartes d’identification — Cartes à circuit(s) intégré(s) sans contact — Cartes de proximité —

Partie 4: Protocole de transmission
AMENDEMENT 6: Clarification des S(PARAMETERS)
ICS: 35.240.15
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/IEC 14443-4:2008/DAM 6:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO/IEC 2015
---------------------- Page: 1 ----------------------
ISO/IEC 14443-4:2008/DAM 6:2015(E)
COPYRIGHT PROTECTED DOCUMENT
©  ISO/IEC 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO/IEC 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 14443-4:2015/FPDAM 6
Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical

Commission) form the specialized system for worldwide standardization. National bodies that are members of

ISO or IEC participate in the development of International Standards through technical committees

established by the respective organization to deal with particular fields of technical activity. ISO and IEC

technical committees collaborate in fields of mutual interest. Other international organizations, governmental

and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information

technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of the joint technical committee is to prepare International Standards. Draft International

Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as

an International Standard requires approval by at least 75 % of the national bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.

Amendment 6 to ISO/IEC 14443-4:2015 was prepared by Joint Technical Committee ISO/IEC JTC 1,

Information Technology, Subcommittee SC 17, Identification cards.
© ISO/IEC 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
DRAFT AMENDMENT ISO/IEC 14443-4:2015/FPDAM 6
Contactless integrated circuit cards — Proximity — Part 4:
Transmission Protocol - Amendment 6: S(PARAMETERS)
clarification
Page 22, 7.1.2.1
Delete the Note
Page 29, 7.5.1
Replace the subclause with the following:

"After the activation sequence, the PCD may send at any time a first S(PARAMETERS) block with or without

INF field to check if S(PARAMET
...