Identification cards — Recording technique — Part 2: Magnetic stripe: Low coercivity

ISO/IEC 7811 defines the characteristics for identification cards as defined in Clause 4 of this document and the use of such cards for international interchange. This document specifies requirements for a low coercivity magnetic stripe (including any protective overlay) on an identification card, the encoding technique and coded character sets. It takes into consideration both human and machine aspects and states minimum requirements. Coercivity influences many of the quantities specified in this document but is not itself specified. ISO/IEC 7811 provides criteria to which cards are to perform. No consideration is given within ISO/IEC 7811 to the amount of use, if any, experienced by the card prior to test. Failure to conform to specified criteria is negotiated between the involved parties. ISO/IEC 10373-2 specifies the test procedures used to check cards against the parameters specified in this document. NOTE Numeric values in the SI and/or Imperial measurement system in this document may have been rounded off and are consistent with, but not exactly equal to each other. Using either system is correct but intermixing or reconverting values can result in errors. The original design was made using the Imperial measurement system.

Cartes d'identification — Technique d'enregistrement — Partie 2: Bandeau magnétique: Faible coercivité

General Information

Status
Published
Publication Date
06-Aug-2018
Current Stage
9060 - Close of review
Start Date
04-Mar-2029
Ref Project

Relations

Buy Standard

Standard
ISO/IEC 7811-2:2018 - Identification cards -- Recording technique
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 7811-2
Fifth edition
2018-08
Identification cards — Recording
technique —
Part 2:
Magnetic stripe: Low coercivity
Cartes d'identification — Technique d'enregistrement —
Partie 2: Bandeau magnétique: Faible coercivité
Reference number
ISO/IEC 7811-2:2018(E)
©
ISO/IEC 2018

---------------------- Page: 1 ----------------------
ISO/IEC 7811-2:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO/IEC 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 7811-2:2018(E)

Contents Page
Foreword .v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Conformance .3
5 Physical characteristics of the identification card .3
5.1 General . 3
5.2 Magnetic stripe area warpage. 3
5.3 Surface distortions . 3
6 Physical characteristics of the magnetic stripe .4
6.1 Height and surface profile of the magnetic stripe area . 4
6.1.1 Surface profile of the magnetic stripe area . 5
6.1.2 Height of the magnetic stripe area . 6
6.2 Surface roughness . 6
6.3 Adhesion of stripe to card . 6
6.4 Wear of magnetic stripe from read/write head . 7
6.5 Resistance to chemicals . 7
7 Performance characteristics for the magnetic material .7
7.1 General . 7
7.2 Testing and operating environment .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.