oSIST prEN 6101:2019

Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series

This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application.

Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-Reihe

Série aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inches

La présente Norme européenne spécifie les dimensions, les tolérances et les masses des rivets de précision à tête fraisée moyenne 100°, série en inches, pour les applications aérospatiales.

Aeronavtika - Kovice, 100° srednje ugrezna glava, ozka toleranca - Palčne mere

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-ReiheSérie aérospatiale - Rivets de précision, tête fraisée moyenne 100° - Série en inchesAerospace series - Rivet, 100° medium flush head, close tolerance - Inch series49.030.60KoviceRivetsICS:Ta slovenski standard je istoveten z:prEN 6101oSIST prEN 6101:2019en,fr,de01-januar-2019oSIST prEN 6101:2019SLOVENSKI

STANDARD
oSIST prEN 6101:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
DRAFT prEN 6101
October
t r s z ICS
v {ä r u rä x r Will supersede EN
x s r sã t r s xEnglish Version
Aerospace series æ Rivetá

s r r ¹ medium flush headá close tolerance æ Inch series Série aérospatiale æ Rivets de précisioná tête fraisée moyenne

s r r ¹ æ Série en inches
Luftæ und Raumfahrt æ Vollnietá

s r r ¹ Medium Senkkopfá enge Toleranz æ ZollæReihe This draft European Standard is submitted to CEN members for enquiryä It has been drawn up by the Technical Committee ASDæSTANä

If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä

This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä

CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä

Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä

Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels

t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä prEN

x s r sã t r s z EoSIST prEN 6101:2019

prEN 6101:2018 (E) 2 Contents Page European foreword ....................................................................................................................................................... 3 Introduction .................................................................................................................................................................... 4 1 Scope .................................................................................................................................................................... 5 2 Normative references .................................................................................................................................... 5 3 Terms and definitions ................................................................................................................................... 6 4 Requirements ................................................................................................................................................... 6 4.1 Configuration, dimensions, tolerances and mass ................................................................................ 6 4.2 Material and surface treatment .............................................................................................................. 11 5 Designation..................................................................................................................................................... 13 6 Marking ............................................................................................................................................................ 13 6.1 Material identification ............................................................................................................................... 13 6.2 Manufacturer's identification .................................................................................................................. 14 6.3 Identification of oversize rivets .............................................................................................................. 14 7 Technical specification ............................................................................................................................... 15 7.1 Aluminium alloy rivet ................................................................................................................................. 15 7.2 Titanium alloy rivet ..................................................................................................................................... 15 7.3 Heat resisting alloy NI-P9001 (NiCu31) rivets .................................................................................. 15 8 Quality management system .................................................................................................................... 15 Annex A (informative)

Record of revision .......................................................................................................... 16 Bibliography ................................................................................................................................................................. 17

oSIST prEN 6101:2019

prEN 6101:2018 (E) 3 European foreword This document (prEN 6101:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This document is currently submitted to the CEN Enquiry. This document will supersede EN 6101:2016. oSIST prEN 6101:2019

prEN 6101:2018 (E) 4 Introduction This document is published at Airbus agreed version prEN 6101 edition P3. Former issue 1 and 2 and drafts may exist of Airbus development only but without any ASD–STAN official publication. In consequence configuration management discrepancies with these unofficial documents are under Airbus responsibility. oSIST prEN 6101:2019

prEN 6101:2018 (E) 5 1 Scope This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. FprEN 2114, Aerospace series - Aluminium 1050A-H14 - Wire for solid rivets – D

º 10 mm1 EN 2115, Aerospace series - Aluminium alloy 2117-T42 - Wire for solid rivets – D

º 10 mm EN 2116, Aerospace series - Aluminium alloy 2017A-T42 - Wire for solid rivets – D

º 10 mm EN 2117, Aerospace series - Aluminium alloy AL-P5056A (5056A)-H32 - Wire for solid rivets – D

º 10 mm EN 2424, Aerospace series - Marking of aerospace products EN 2941, Aerospace series - Nickel alloy rivets - Technical specification EN 3115, Aerospace series - Aluminium alloy 7050-T73 - Wire for solid rivets – D

º 10 mm EN 4372, Aerospace series - Heat resisting nickel alloy with copper NI-PD9001 (NiCu31) - Wire for solid rivets - D

w v mm prEN 6104, Aerospace series - Rivets, solid, in aluminium or aluminium alloy - Inch series - Technical Specification1 prEN 6118, Aerospace series - Process specification - Aluminium base protection for fasteners1 ISO 8080, Aerospace - Anodic treatment of titanium and titanium alloys - Sulfuric acid process AMS 4982, Titanium alloy wire 44.5 Cb2 AMS-QQ-P-416, Plating, cadmium (electrodeposited)2 MIL-A-8625, Anodic coatings for aluminum and aluminum alloys3 MIL-C-5541, Chemical conversion coatings on aluminium and aluminium alloys3 NAS 9800, Head protrusion gaging, 100° flush head fasteners, gage block, gage diameters and stylus4

1 Under preparation. Published as ASD Prestandard at the date of publication of this standard. 2 Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. 3 Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA. 4 Published by: Aerospace Industries Association of America, Inc. (AIA), 1250 Eye Street, N.W., Washington, D.C. 20005-3924, USA. oSIST prEN 6101:2019

prEN 6101:2018 (E) 6 NASM 5674, Rivets, structural, aluminium alloy, titanium columbium alloy, general specification for4 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databa

...