SIST EN 6081:2016
(Main)Aerospace series - Rivet, universal head, close tolerance - Inch series
Aerospace series - Rivet, universal head, close tolerance - Inch series
This standard specifies the dimensions, tolerances and mass of rivets with universal head, close tolerance, inch series, for aerospace application.
Luft- und Raumfahrt - Vollniet, Universalkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, tête universelle - Série en inches
Aeronavtika - Kovice, univerzalna glava, ozka toleranca - Colska izvedba
Ta standard določa dimenzije, tolerance in maso kovic z univerzalno glavo, ozka toleranca, colska izvedba za uporabo v aeronavtiki.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 6081:2016
01-november-2016
Aeronavtika - Kovice, univerzalna glava, ozka toleranca - Colska izvedba
Aerospace series - Rivet, universal head, close tolerance - Inch series
Luft- und Raumfahrt - Vollniet, Universalkopf, enge Toleranz - Zoll-Reihe
Série aérospatiale - Rivets de précision, tête universelle - Série en inches
Ta slovenski standard je istoveten z: EN 6081:2016
ICS:
49.030.60 Kovice Rivets
SIST EN 6081:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 6081:2016
---------------------- Page: 2 ----------------------
SIST EN 6081:2016
EN 6081
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 49.030.60
English Version
Aerospace series - Rivet, universal head, close tolerance -
Inch series
Série aérospatiale - Rivets de précision, tête universelle Luft- und Raumfahrt - Vollniet, Universalkopf, enge
- Série en inches Toleranz - Zoll-Reihe
This European Standard was approved by CEN on 2 January 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6081:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6081:2016
EN 6081:2016 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Requirements . 5
3.1 Configuration, dimensions, tolerances and mass . 5
3.2 Material and surface treatment. 5
4 Designation . 7
5 Marking . 8
5.1 Material identification . 8
5.2 Manufacturers identification . 8
6 Technical specification . 8
6.1 Titanium alloy rivet . 8
6.2 Aluminium alloy rivet . 8
2
---------------------- Page: 4 ----------------------
SIST EN 6081:2016
EN 6081:2016 (E)
European foreword
This document (EN 6081:2016) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this European
Standard has received the approval of the National Associations and the Official Services of the member
countries of ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn
at the latest by March 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 6081:2016
EN 6081:2016 (E)
1 Scope
This European Standard specifies the dimensions, tolerances and mass of rivets with universal head, close
tolerance,
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Kovice, univerzalna glava, ozka toleranca - Colska izvedbaLuft- und Raumfahrt - Vollniet, Universalkopf, enge Toleranz - Zoll-ReiheSérie aérospatiale - Rivets de précision, tête universelle - Série en inchesAerospace series - Rivet, universal head, close tolerance - Inch series49.030.60KoviceRivetsICS:Ta slovenski standard je istoveten z:FprEN 6081kSIST FprEN 6081:2015en,fr,de01-november-2015kSIST FprEN 6081:2015SLOVENSKI
STANDARD
kSIST FprEN 6081:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 6081
October
t r s w ICS
English Version
Aerospace series æ Rivetá universal headá close tolerance æ Inch series Série aérospatiale æ Rivets de précisioná tête universelle æ Série en inches
Luftæ und Raumfahrt æ Vollnietá Universalkopfá enge Toleranz æ ZollæReihe This draft European Standard is submitted to CEN members for formal voteä It has been drawn up by the Technical Committee ASDæSTANä
If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä
This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä
Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä FprEN
x r z sã t r s w EkSIST FprEN 6081:2015
FprEN 6081:2015 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements . 4 3.1 Configuration, dimensions, tolerances and mass . 4 3.2 Material and surface treatment . 5 4 Designation. 7 5 Marking . 7 5.1 Material identification . 7 5.2 Manufacturers identification . 8 6 Technical specification . 8 6.1 Titanium alloy rivet . 8 6.2 Aluminium alloy rivet . 8
kSIST FprEN 6081:2015
FprEN 6081:2015 (E) 3 European foreword This document (FprEN 6081:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This document is currently submitted to the Formal Vote.
kSIST FprEN 6081:2015
FprEN 6081:2015 (E) 4 1 Scope This European standard specifies the dimensions, tolerances and mass of rivets with universal head, close tolerance, inch series, for aerospace application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.