Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series

This European Standard specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application.

Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-Reihe

Série aérospatiale - Rivets de précision, 100° tête fraisée médium - Série en inches

Aeronavtika - Zakovica, 100° srednje poglobljena glava, ozka toleranca - Colska izvedba

Ta evropski standard določa dimenzije, tolerance in maso zakovic s 100° srednje poglobljeno glavo, ozka toleranca, colska izvedba za uporabo v aeronavtiki.

General Information

Status
Published
Publication Date
12-Oct-2016
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Sep-2016
Due Date
21-Nov-2016
Completion Date
13-Oct-2016

RELATIONS

Buy Standard

Standard
SIST EN 6101:2016
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 6101:2016
01-november-2016
Aeronavtika - Zakovica, 100° srednje poglobljena glava, ozka toleranca - Colska
izvedba
Aerospace series - Rivet, 100° medium flush head, close tolerance - Inch series
Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf, enge Toleranz - Zoll-Reihe

Série aérospatiale - Rivets de précision, 100° tête fraisée médium - Série en inches

Ta slovenski standard je istoveten z: EN 6101:2016
ICS:
49.030.60 Kovice Rivets
SIST EN 6101:2016 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 6101:2016
---------------------- Page: 2 ----------------------
SIST EN 6101:2016
EN 6101
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 49.030.60
English Version
Aerospace series - Rivet, 100° medium flush head, close
tolerance - Inch series

Série aérospatiale - Rivets de précision, 100° tête Luft- und Raumfahrt - Vollniet, 100° Medium Senkkopf,

fraisée médium - Série en inches enge Toleranz - Zoll-Reihe
This European Standard was approved by CEN on 11 March 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6101:2016 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6101:2016
EN 6101:2016 (E)
Contents Page

European foreword ................................................................................................................................................................ 3

1 Scope ............................................................................................................................................................................ 4

2 Normative references ............................................................................................................................................ 4

3 Requirements ............................................................................................................................................................ 5

3.1 Configuration, dimensions, tolerances and mass ........................................................................................ 5

3.2 Material and surface treatment.......................................................................................................................... 5

4 Designation ................................................................................................................................................................ 9

5 Marking ..................................................................................................................................................................... 10

5.1 Material identification ......................................................................................................................................... 10

5.2 Manufacturers identification ............................................................................................................................ 11

5.3 Identification of oversize rivets ....................................................................................................................... 11

6 Technical specification ........................................................................................................................................ 11

6.1 Aluminium alloy rivet .......................................................................................................................................... 11

6.2 Heat resisting alloy NiCu31 rivets ................................................................................................................... 11

6.3 Titanium alloy rivet .............................................................................................................................................. 11

---------------------- Page: 4 ----------------------
SIST EN 6101:2016
EN 6101:2016 (E)
European foreword

This document (EN 6101:2016) has been prepared by the Aerospace and Defence Industries Association of

Europe - Standardization (ASD-STAN).

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has

received the approval of the National Associations and the Official Services of the member countries of ASD,

prior to its presentation to CEN.

This European Standard shall be given the status of a national standard, either by publication of an identical

text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn

at the latest by March 2017.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,

Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

---------------------- Page: 5 ----------------------
SIST EN 6101:2016
EN 6101:2016 (E)
1 Scope

This European Standard specifies the dimensions, tolerances and mass of rivets with 100° medium flush

head, close tolerance, inch series, for aerospace application.
2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated references,

the latest edition of the referenced document (including any amendments) applies.

EN 2114, Aluminium 1050A-H14 — Wire for solid rivets — D ≤ 10 mm

EN 2115, Aerospace series — Aluminium alloy 2117-T42 — Wire for solid rivets — D ≤ 10 mm

EN 2116, Aerospace series — Aluminium alloy 2017A-T42 — Wire for solid rivets — D ≤ 10 mm

EN 2117, Aerospace series — Aluminium alloy AL-P5056A (5056A)-H32 — Wire for solid rivets — D ≤ 10 mm

EN 2424, Aerospace series — Marking of aerospace products
EN 2941, Aerospace series — Nickel alloy rivets — Technical specification

EN 3115, Aerospace series — Aluminium alloy 7050-T73 — Wire for solid rivets — D ≤ 10 mm

EN 4372, Aerospace series — Heat resisting nickel alloy with copper NI-PD9001 (NiCu31) — Wire for solid

rivets — D ≤ 10 mm

EN 6104, Aerospace series — Rivets, solid, in aluminium or aluminium alloy — Inch

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.