25.100.30 - Drills, countersinks, reamers
Drills, countersinks, reamers
Bohrer. Senker. Raumwerkzeuge
Forets, outils a chanfreiner et alésoirs
Svedri, greznila, posnemalna orodja
General Information
This document specifies the dimensions of machine bridge reamers. It gives, for a series of diameter ranges, d1, from 6 mm to 50,8 mm, the values, in millimetres, for the following dimensions of these tools: — overall length, l3; — total cutting edge length, l2; — tapered cutting edge length, l1. Unless otherwise stated, these reamers are right-hand cutting.
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off
This International Standard specifies the dimensions of centre drills for centre holes without protecting
chamfers (Type A).
It covers only metric dimensions, which are regarded as the only recommended dimensions in the
future for this type of drill.
The flutes may be straight or spiral, depending on the manufacturer’s discretion.
Unless otherwise indicated, these drills will be right-hand cutting.
Recommended dimensions for Type A centre holes, which can be obtained by a rational use of t...view more
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
This International Standard specifies the dimensions of centre drills for centre holes with protecting
chamfer — Type B.
It covers only metric dimensions, regarded as the only recommended dimensions in the future for this
type of drills.
The flutes can be straight or spiral at the option of manufacturer.
Unless otherwise stated, these drills are right-hand cutting.
Annex A gives the recommended dimensions for the centre holes, Type B, which can be obtained by a
rational use of the centre ...view more
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
This International Standard specifies the dimensions of centre drills for centre holes with radius —
Type R.
It covers only metric dimensions, regarded as the only recommended dimensions in the future for this
type of drills.
The flutes can be straight or spiral at the option of manufacturer.
Unless otherwise stated, these drills are right-hand cutting.
Annex A gives the recommended dimensions for the centre holes, Type R, which can be obtained by a
rational use of the centre drills liste...view more
- Standard5 pagesFrench language
sale 15% off- Standard5 pagesEnglish language
sale 15% off- Standard10 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 5468:2017 specifies the dimensions, in millimetres, of rotary and rotary impact masonry drill bits with hardmetal tips, having diameters in the range of 4 mm to 25 mm inclusive and overall, and working lengths in the series short, long and extra-long. It does not apply to hammer drills.
- Standard5 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 494:2017 specifies the dimensions of cylindrical shank twist drills having working lengths in the long series. The cylindrical shank jobber and stub series drills and Morse taper shank drills are given in ISO 235.
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off
ISO 2250:2017 specifies the dimensions of cylindrical shank socket reamers and taper shank socket reamers manufactured to produce self-holding taper sockets for self-holding taper shanks of the following designations, and which are in accordance with ISO 296: - metric tapers no. 4 and no. 6; - Morse tapers no. 0 to no. 6 inclusive. NOTE Unless otherwise stated, these reamers are right-hand cutting.
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 235:2016 specifies the dimensions of the following three types of drills: a) parallel shank drills, stub series; b) parallel shank drills, jobber series; c) Morse taper shank drills. It comprises, for each type of drill mentioned above, three tables giving, respectively: a) the dimensions in millimetres; b) the dimension in inches; c) the corresponding lengths, in millimetres and in inches, set out as functions of diameter steps.
- Standard21 pagesFrench language
sale 15% off- Standard20 pagesEnglish language
sale 15% off
ISO 2540:2016 specifies the dimensions of centre drills for centre holes with protecting chamfer ? Type B. It covers only metric dimensions, regarded as the only recommended dimensions in the future for this type of drills. The flutes can be straight or spiral at the option of manufacturer. Unless otherwise stated, these drills are right-hand cutting. Annex A gives the recommended dimensions for the centre holes, Type B, which can be obtained by a rational use of the centre drills listed in this...view more
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 4205:2016 specifies the dimensions, in millimetres, and the tolerances of 90° countersinks with parallel shanks and solid pilots for general use.
- Standard3 pagesFrench language
sale 15% off- Standard3 pagesEnglish language
sale 15% off
ISO 2541:2016 specifies the dimensions of centre drills for centre holes with radius ? Type R. It covers only metric dimensions, regarded as the only recommended dimensions in the future for this type of drills. The flutes can be straight or spiral at the option of manufacturer. Unless otherwise stated, these drills are right-hand cutting. Annex A gives the recommended dimensions for the centre holes, Type R, which can be obtained by a rational use of the centre drills listed in this Internation...view more
- Standard5 pagesFrench language
sale 15% off- Standard5 pagesEnglish language
sale 15% off- Standard10 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 3291:2016 specifies the dimensions of extra-long Morse taper shank drills in the range of 6 mm to 50 mm diameter with an overall length range of 200 mm to 630 mm.
- Standard5 pagesFrench language
sale 15% off- Standard5 pagesEnglish language
sale 15% off
ISO 4206:2016 specifies the dimensions, in millimetres, and the tolerances of counterbores with parallel shanks and solid pilots for general use.
- Standard3 pagesFrench language
sale 15% off- Standard3 pagesEnglish language
sale 15% off
ISO 7079:2016 specifies the dimensions of core drills with parallel shanks and with Morse taper shanks. It includes two tables for each of the above specified types, giving respectively - the dimensions for the preferred diameter (see Tables 1 and 2), and - the corresponding lengths defined in terms of diameter ranges (see Tables 3 and 4). The tables show only metric dimensions which are alone recommended in the future for this type of drill. Unless otherwise stated, these drills will be right-h...view more
- Standard9 pagesFrench language
sale 15% off- Standard9 pagesEnglish language
sale 15% off
ISO 3292:2016 specifies the dimensions of extra-long parallel shank twist drills in the range of 2 mm to 14 mm diameter with an overall length range of 125 mm to 400 mm.
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 4204:2016 specifies the dimensions of 90° countersinks with Morse taper shanks and detachable pilots for general use.
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 10998:2016 specifies the dimensions and technical specifications of spot drills of high-speed steel and hardmetal with a point angle of 90° or 120°.
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 866:2016 specifies the dimensions of centre drills for centre holes without protecting chamfers (Type A). It covers only metric dimensions, which are regarded as the only recommended dimensions in the future for this type of drill. The flutes may be straight or spiral, depending on the manufacturer's discretion. Unless otherwise indicated, these drills will be right-hand cutting. Recommended dimensions for Type A centre holes, which can be obtained by a rational use of the centre drills list...view more
- Standard6 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO 3293:2016 specifies the dimensions of Morse taper shank countersinks for angles 60°, 90° and 120° inclusive. It specifies dimensions in metric units only, these being regarded as the only recommended dimensions in the future, for countersinks with cutting diameters in the range 16 mm to 80 mm. The dimensions given apply only to tools made from high speed steel. However, if the method of production allows, the shanks may be manufactured from a suitable alternative material, such as a carbon s...view more
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
ISO 3294:2016 specifies the dimensions of parallel shank countersinks for angles 60°, 90° and 120° inclusive. It specifies dimensions in metric units only, these being regarded as the only recommended dimensions in the future, for countersinks with cutting diameters in the range 8 mm to 25 mm. The dimensions apply only to tools made from high-speed steel. However, if the method of production allows, the shanks may be manufactured from a suitable alternative material, such as a carbon steel. Unle...view more
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off