Cylindrical shank twist drills — Long series

ISO 494:2017 specifies the dimensions of cylindrical shank twist drills having working lengths in the long series. The cylindrical shank jobber and stub series drills and Morse taper shank drills are given in ISO 235.

Forets à queue cylindrique — Série longue

ISO 494:2017 spécifie les dimensions des forets à queue cylindriques, série longue. Les forets à queue cylindrique courts et extra-courts et les forets à queue cône Morse sont couverts par l'ISO 235.

General Information

Status
Published
Publication Date
23-Feb-2017
Current Stage
9093 - International Standard confirmed
Completion Date
31-Oct-2022
Ref Project

Relations

Buy Standard

Standard
ISO 494:2017 - Cylindrical shank twist drills -- Long series
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 494:2017 - Forets a queue cylindrique -- Série longue
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 494
Third edition
2017-02
Cylindrical shank twist drills — Long
series
Forets à queue cylindrique — Série longue
Reference number
ISO 494:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 494:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 494:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 General . 1
4.2 General dimensions . 1
4.3 Lengths set out as functions of diameter steps . 3
5 Cutting length. 4
6 Shank . 4
Annex A (informative) Relationship between designations in this document and the
ISO 13399 series . 5
Bibliography . 6
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 494:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools
with defined cutting edges, cutting items.
This third edition cancels and replaces the second edition (ISO 494:2009), of which it constitutes a
minor revision with the following change:
— added Annex A, giving the relationship between the symbols of this document and the symbols
according to the ISO 13399 series.
iv © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 494:2017(E)
Cylindrical shank twist drills — Long series
...

NORME ISO
INTERNATIONALE 494
Troisième édition
2017-02
Forets à queue cylindrique — Série
longue
Cylindrical shank twist drills — Long series
Numéro de référence
ISO 494:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 494:2017(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 494:2017(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Dimensions . 1
4.1 Généralités . 1
4.2 Dimensions générales . 1
4.3 Longueurs définies en fonction des paliers de diamètres . 3
5 Longueur de coupe . 4
6 Queue. 4
Annexe A (informative) Relation entre les désignations le présent document et la série
ISO 13399 . 5
Bibliographie . 6
© ISO 2017 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 494:2017(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien
suivant: Avant-propos — Informations supplémentaires
Le présent document a été élaboré par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 9,
Outils à arêtes de coupe définies, éléments coupants.
Cette troisième édition annule et remplace la deuxième édition (ISO 494:2009), dont elle constitue une
révision mineure avec la modification suivante:
— ajout de l’Annexe A, donnant la relation entre les symboles du présent document et les symboles de
la série des ISO 13399.
iv © ISO 2017 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 494:2017(F)
Forets à queue cylindrique — Série longue
1 Domaine d’a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.