Counterbores with parallel shanks and solid pilots

ISO 4206:2016 specifies the dimensions, in millimetres, and the tolerances of counterbores with parallel shanks and solid pilots for general use.

Outils à lamer, à queue cylindrique et pilote fixe

ISO 4206:2016 spécifie les dimensions, en millimètres, et les tolérances des outils à lamer, à queue cylindrique et pilote fixe, d'usage général.

General Information

Status
Published
Publication Date
13-Oct-2016
Current Stage
9093 - International Standard confirmed
Completion Date
31-Oct-2022
Ref Project

Relations

Buy Standard

Standard
ISO 4206:2016 - Counterbores with parallel shanks and solid pilots
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4206:2016 - Outils a lamer, a queue cylindrique et pilote fixe
French language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4206
Third edition
2016-10-15
Counterbores with parallel shanks
and solid pilots
Outils à lamer, à queue cylindrique et pilote fixe
Reference number
ISO 4206:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 4206:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4206:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions . 1
Annex A (informative) Relationship between designations of this International Standard
and ISO 13399 . 2
Bibliography . 3
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 4206:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in th
...

NORME ISO
INTERNATIONALE 4206
Troisième édition
2016-10-15
Outils à lamer, à queue cylindrique et
pilote fixe
Counterbores with parallel shanks and solid pilots
Numéro de référence
ISO 4206:2016(F)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 4206:2016(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 4206:2016(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Dimensions . 1
Annexe A (informative) Relation entre les désignations dans la présente Norme
internationale et l’ISO 13399 . 2
Bibliographie . 3
© ISO 2016 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 4206:2016(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.