ISO/IEC/IEEE FDIS 8802-22

Telecommunications and information exchange between systems — Wireless Regional Area Networks (WRAN) — Specific requirements — Part 22: Cognitive Wireless RAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and procedures for operation in the bands that allow spectrum sharing where the communications devices may opportunistically operate in the spectrum of primary service

This document specifies the air interface, including the cognitive radio medium access control layer (MAC) and physical layer (PHY), of point-to-multipoint and backhaul wireless regional area networks (WRANs) comprised of a professional fixed base station (BS) with fixed and portable user terminals. The document specifies operation in the bands that allow spectrum sharing where the communications devices may opportunistically operate in the spectrum of the primary service, such as the VHF/UHF TV broadcast bands between 54 MHz to 862 MHz, and the 1300 MHz to 1750 MHz and 2700 MHz to 3700 MHz bands provided the regulatory regime allows it.

Télécommunications et échange d'information entre systèmes — Réseaux régionaux sans fil (WRAN) — Exigences spécifiques — Partie 22: Spécifications du contrôle d'accès du milieu sans fil cognitif (MAC) et de la couche physique (PHY) : Politiques et procédures pour le fonctionnement dans les bandes qui permettent le partage du spectre, où les dispositifs de communication peuvent fonctionner de manière opportuniste dans le spectre du service primaire

General Information

• Status: Published
• ICS: 35.110 - Networking
• Technical Committee: ISO/IEC JTC 1/SC 6 - Telecommunications and information exchange between systems
• Drafting Committee: ISO/IEC JTC 1/SC 6 - Telecommunications and information exchange between systems

RELATIONS

• Revises: ISO/IEC/IEEE 8802-22:2015 - Information technology — Telecommunications and information exchange between systems — Local and metropolitan area networks — Specific requirements — Part 22: Cognitive Wireless RAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV Bands
• Effective Date: 17-Jul-2021

Standards Content (sample)

FINAL
INTERNATIONAL ISO/IEC/
DRAFT
STANDARD IEEE/FDIS
8802-22
ISO/IEC JTC 1/SC 6
Telecommunications and information
Secretariat: KATS
exchange between systems — Wireless
Voting begins on:
2021-07-22 Regional Area Networks (WRAN) —
Specific requirements —
Voting terminates on:
2021-12-09
Part 22:
Cognitive Wireless RAN Medium
Access Control (MAC) and Physical
Layer (PHY) Specifications: Policies
and procedures for operation in the
bands that allow spectrum sharing
where the communications devices
may opportunistically operate in the
spectrum of primary service
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/IEC/IEEE FDIS 8802-22:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. IEEE 2021
---------------------- Page: 1 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© IEEE 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from IEEE at the address below.

Institute of Electrical and Electronics Engineers, Inc
3 Park Avenue, New York
NY 10016-5997, USA
Email: [e-mail]
Website: www.ieee.org
Published in Switzerland
ii © IEEE 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC/IEEE DIS 8802-22:2021(E)
Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical

Commission) form the specialized system for worldwide standardization. National bodies that are

members of ISO or IEC participate in the development of International Standards through technical

committees established by the respective organization to deal with particular fields of technical activity.

ISO and IEC technical committees collaborate in fields of mutual interest. Other international

organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the

work.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO/IEC documents should be noted. This document was drafted in accordance with

the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives or

www.iec.ch/members_experts/refdocs).

IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating

Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its

standards through a consensus development process, approved by the American National Standards

Institute, which brings together volunteers representing varied viewpoints and interests to achieve the

final product. Volunteers are not necessarily members of the Institute and serve without compensation.

While the IEEE administers the process and establishes rules to promote fairness in the consensus

development process, the IEEE does not independently evaluate, test, or verify the accuracy of any of the

information contained in its standards.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details

of any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents) or the IEC list of patent

declarations received (see patents.iec.ch).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the World

Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),

see www.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-standards.

ISO/IEC/IEEE 8802-22 was prepared by the LAN/MAN of the IEEE Computer Society (as IEEE Std

802.22-2019) and drafted in accordance with its editorial rules. It was adopted, under the “fast-track

procedure” defined in the Partner Standards Development Organization cooperation agreement between

ISO and IEEE, by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 6,

Telecommunications and information exchange between systems.

This second edition cancels and replaces the first edition (ISO/IEC/IEEE 8802-22:2015), which has been

technically revised.

A list of all parts in the ISO/IEC/IEEE 8802 series can be found on the ISO and IEC websites.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html and www.iec.ch/national-

committees.
© ISO 2021 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Important Notices and Disclaimers Concerning IEEE Standards Documents

2 IEEE documents are made available for use subject to important notices and legal disclaimers. These

3 notices and disclaimers, or a reference to this page, appear in all standards and may be found under the

4 heading “Important Notices and Disclaimers Concerning IEEE Standards Documents.” They can also be

5 obtained on request from IEEE or viewed at http://standards.ieee.org/IPR/disclaimers.html.

6 Notice and Disclaimer of Liability Concerning the Use of IEEE Standards
7 Documents

8 IEEE Standards documents (standards, recommended practices, and guides), both full-use and trial-use, are

9 developed within IEEE Societies and the Standards Coordinating Committees of the IEEE Standards

10 Association (“IEEE-SA”) Standards Board. IEEE (“the Institute”) develops its standards through a

11 consensus development process, approved by the American National Standards Institute (“ANSI”), which

12 brings together volunteers representing varied viewpoints and interests to achieve the final product. IEEE

13 Standards are documents developed through scientific, academic, and industry-based technical working

14 groups. Volunteers in IEEE working groups are not necessarily members of the Institute and participate

15 without compensation from IEEE. While IEEE administers the process and establishes rules to promote

16 fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the

17 accuracy of any of the information or the soundness of any judgments contained in its standards.

18 IEEE Standards do not guarantee or ensure safety, security, health, or environmental protection, or ensure

19 against interference with or from other devices or networks. Implementers and users of IEEE Standards

20 documents are responsible for determining and complying with all appropriate safety, security,

21 environmental, health, and interference protection practices and all applicable laws and regulations.

22 IEEE does not warrant or represent the accuracy or content of the material contained in its standards, and

23 expressly disclaims all warranties (express, implied and statutory) not included in this or any other

24 document relating to the standard, including, but not limited to, the warranties of: merchantability; fitness

25 for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness

26 of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort.

27 IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.”

28 Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there

29 are no other ways to produce, test, measure, purchase, market, or provide other goods and services related

30 to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved

31 and issued is subject to change brought about through developments in the state of the art and comments

32 received from users of the standard.

33 In publishing and making its standards available, IEEE is not suggesting or rendering professional or other

34 services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any

35 other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his

36 or her own independent judgment in the exercise of reasonable care in any given circumstances or, as

37 appropriate, seek the advice of a competent professional in determining the appropriateness of a given

38 IEEE standard.

39 IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

40 EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO:
41 PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
42 OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
43 WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
44 OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE
45 UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND
46 REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.
© IEEE 2021 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Translations

2 The IEEE consensus development process involves the review of documents in English only. In the event

3 that an IEEE standard is translated, only the English version published by IEEE should be considered the

4 approved IEEE standard.
5 Official statements

6 A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board

7 Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its

8 committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures,

9 symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall

10 make it clear that his or her views should be considered the personal views of that individual rather than the

11 formal position of IEEE.
12 Comments on standards

13 Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of

14 membership affiliation with IEEE. However, IEEE does not provide consulting information or advice

15 pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a

16 proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a

17 consensus of concerned interests, it is important that any responses to comments and questions also receive

18 the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and

19 Standards Coordinating Committees are not able to provide an instant response to comments or questions

20 except in those cases where the matter has previously been addressed. For the same reason, IEEE does not

21 respond to interpretation requests. Any person who would like to participate in revisions to an IEEE

22 standard is welcome to join the relevant IEEE working group.
23 Comments on standards should be submitted to the following address:
24 Secretary, IEEE-SA Standards Board
25 445 Hoes Lane
26 Piscataway, NJ 08854 USA
27 Laws and regulations

28 Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with

29 the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory

30 requirements. Implementers of the standard are responsible for observing or referring to the applicable

31 regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not

32 in compliance with applicable laws, and these documents may not be construed as doing so.

33 Copyrights

34 IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws.

35 They are made available by IEEE and are adopted for a wide variety of both public and private uses. These

36 include both use, by reference, in laws and regulations, and use in private self-regulation, standardization,

37 and the promotion of engineering practices and methods. By making these documents available for use and

38 adoption by public authorities and private users, IEEE does not waive any rights in copyright to the

39 documents.
© IEEE 2021 – All rights reserved
---------------------- Page: 5 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Photocopies

2 Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to

3 photocopy portions of any individual standard for company or organizational internal use or individual,

4 non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance

5 Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; [phone]. Permission

6 to photocopy portions of any individual standard for educational classroom use can also be obtained

7 through the Copyright Clearance Center.
8 Updating of IEEE Standards documents

9 Users of IEEE Standards documents should be aware that these documents may be superseded at any time

10 by the issuance of new editions or may be amended from time to time through the issuance of amendments,

11 corrigenda, or errata. A current IEEE document at any point in time consists of the current edition of the

12 document together with any amendments, corrigenda, or errata then in effect.

13 Every IEEE standard is subjected to review at least every ten years. When a document is more than ten

14 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although

15 still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to

16 determine that they have the latest edition of any IEEE standard.

17 In order to determine whether a given document is the current edition and whether it has been amended

18 through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at

19 http://ieeexplore.ieee.org/ or contact IEEE at the address listed previously. For more information about the

20 IEEE-SA or IEEE’s standards development process, visit the IEEE-SA Website at http://standards.ieee.org.

21 Errata

22 Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL:

23 http://standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata

24 periodically.
25 Patents

26 Attention is called to the possibility that implementation of this standard may require use of subject matter

27 covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to

28 the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant

29 has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the

30 IEEE-SA Website at http://standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may

31 indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without

32 compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of

33 any unfair discrimination to applicants desiring to obtain such licenses.

34 Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not

35 responsible for identifying Essential Patent Claims for which a license may be required, for conducting

36 inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or

37 conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing

38 agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that

39 determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely

40 their own responsibility. Further information may be obtained from the IEEE Standards Association.

© IEEE 2021 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Participants

2 At the time this draft standard was completed, the Wireless Regional Area Networks Working Group had

3 the following membership:
4 Apurva N. Mody, Chair
5 Oliver Holland, Vice Chair
6 Ranga Reddy, Lead Editor
8 Participant1 11 Participant4 14 Participant7
9 Participant2 12 Participant5 15 Participant8
10 Participant3 13 Participant6 16 Participant9

18 The following members of the balloting committee voted on this standard. Balloters may have voted for

19 approval, disapproval, or abstention.
21 Baker Kenneth 29 Hwang SunghYun 37 Pyo Chang-woo
22 Chouinard Gerald 30 Holland Oliver 38 Reddy Ranga K.
23 Cotton Michael 31 Kalke Jerome 39 Reede Ivan
24 Das Subir 32 Khambekar Nilesh 40 Shellhammer Steven
25 Grove Bob 33 Miele Gianfranco 41 Suriaputra William
26 Harada Hiroshi 34 Mody Apurva 42 Stan Luc
27 Heile Bob 35 Nikolich Paul 43 Villardi Gabriel
28 Hislop Roger 36 Oodo Masayaki

45 When the IEEE-SA Standards Board approved this standard on , it had the following

46 membership:
48 Jean-Philippe Faure, Chair
49 Gary Hoffman, Vice Chair
50 John D. Kulick, Past Chair
51 Konstantinos Karachalios, Secretary
52 Ted Burse 60 Xiaohui Liu 68 Dorothy Stanley
53 Guido R. Hiertz 61 Kevin Lu 69 Mehmet Ulema
54 Gary Hoffman 62 Daleep Mohla 70 Phil Wennblom
55 Christel Hunter 63 Andrew Myles 71 Philip Winston
56 *Joseph L. Koepfinger 64 Paul Nikolich 72 Howard Wolfman
57 Thomas Koshy 65 Ronald C. Petersen
73 Jingyi Zhou
58 Hung Ling 66 Annette D. Reilly
59 Dong Liu 67 Robby Robson
74 *Member Emeritus
Copyright © 2019 IEEE. All rights reserved.
This is an unapproved IEEE Standards Draft, subject to change.
© IEEE 2021 – All rights reserved
---------------------- Page: 7 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Historical Participants

2 At the time this standard was submitted to the IEEE-SA for approval, the following voting members had

3 participated in the IEEE P802.22 Working Group until December 2011.
4 Apurva N. Mody, Chair
5 Gerald Chouinard, Vice-chair and lead editor
7 Kyu Hwan An 54 Mark Hopkins 101 Max Muterspaugh
8 Chee Wei Ang 55 Victor Hou 102 Mullaguru Naidu
9 Kwok Shum Au 56 Wendong Hu 103 Paul Nikolich
10 Mark Austin 57 Junhong Hui 104 John Notor
11 Anuj Batra 58 Sung Hyun Hwang 105 Moh Nouroozian
12 John Benko 59 Duckdong Hwang 106 Seungmok Oh
13 Robert Berger 60 Tae-In Hyon 107 Barry O’Mahony
14 Dagnachew Birru 61 Yutaka Ikeda 108 Ashish Pandharipande
15 Scott Blue 62 Soon Ik Jeon 109 Juha Pihlaja
16 Monique Bourgeois Brown 63 Baowei Ji 110 Patrick Pirat
17 Gregory Buchwald 64 Ravi Kalavakunta 111 Ron Porat
18 Winston Caldwell 65 Jerome J. Kalke 112 Jeff Poston
19 Ed Callaway 66 Bub-Joo Kang 113 Jim Raab
20 Dave Cavalcanti 67 Mark Kelley 114 Mohammad Rahman
21 Kiran Challapali 68 Ramon Khalona 115 Ranga K. Reddy
22 Soo-Young Chang 69 Thomas Kiernan 116 Ivan Reede
23 Remi Chayer 70 Chang-Joo Kim 117 Edgar Reihl
24 Shiuh Yuan Chen 71 Kihong Kim 118 Jon Walter Rosdahl
25 Tao Chen 72 Sangbum Kim 119 William Rose
26 Jinxia Cheng 73 HakSun Kim 120 Luis Escobar Sanz
27 Aik Chindapol 74 Byoung-Jo Kim 121 Shigenobu Sasaki
28 InHwan Choi 75 Gwangzeen Ko 122 Jeffrey Schiffer
29 Liwen Chu 76 Tom Kolze 123 Chris Seagren
30 Joon-Hwa Chun 77 Bruce Kraemer 124 Alireza Seyedi
31 Chris Clanton 78 Steve Kuffner 125 Cheng Shan
32 Charles Cook 79 Denis Kuwahara 126 Steve Shellhammer
33 Charles Cooper 80 Jeong Suk Lee 127 Dave Silk
34 Carlos Cordeiro 81 Chang-Ho Lee 128 Kirk Skeba
35 Subir Das 82 Geunho Lee 129 Douglas Smith
36 W. Carl Day 83 Haeyoung Lee 130 Eli Sofer
37 Upkar Dhaliwal 84 Zhongding Lei 131 Myung Sun Song
38 Johnny Dixon 85 Wing Seng Leon 132 Srikathyayani Srikanteswara
39 Peter Ecclesine 86 Barry Lewis 133 Jayne Stancavage
40 Charles Einolf 87 Lingjie Li 134 Carl Stevenson
41 Michael Fischer 88 Ying-Chang Liang 135 William Stiles
42 Wen Gao 89 Kyutae Lim 136 Hideki Tanaka
43 Ingo Gaspard 90 Euntack Lim 137 Clifford Tavares
44 Monisha Ghosh 91 Jiezhen Lin 138 Victor Tawil
45 Joanna Guenin 92 Jinnan Liu 139 Shawn Taylor
46 Jin Guo 93 Hang Liu 140 Paul Thompson
47 Thomas Gurley 94 Michael Lynch 141 James Tomcik
48 JaeSong Han 95 Steve Mace 142 JungSun Um
49 Hiroshi Harada 96 David Magee 143 George Vlantis
50 Ahren Hartman 97 Ben Manny 144 Lei Wang
51 Robert F. Heile 98 David Mazzarese 145 Jianfeng Wang
52 Anh Twan Hoang 99 Tony Morella 146 Yunbiao Wang
53 Michael Hoghooghi 100 Peter Murray 147 Tom Wasilewski
viii
Copyright © 2019 IEEE. All rights reserved.
This is an unapproved IEEE Standards Draft, subject to change.
© IEEE 2021 – All rights reserved
---------------------- Page: 8 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Alfred Wieczorek 5 Bo Xia 8 Steve Yao
2 Kelly Williams 6 Changlong Xu 9 Yonghong Zeng
3 Yuchun Wu 7 ShanShan Xu 10 Jianwei Zhang
4 Shiquan Wu 11 Xin Zhang
12 13
14 Major contributions to this standard were made by the following individuals:
16 Kwok Shum Au 32 Thomas Kiernan 45 Mogh Nouroozian
17 John Benko 33 Kihong Kim 46 Ashish Pandharipande
18 Winston Caldwell 34 Sangbum Kim 47 Patrick Pirat
19 Dave Cavalcanti 35 Kak-Sun Kim 48 Mohammad Rahman
20 Soo-Young Chang 36 Gwangzeen Ko 49 Ranga K. Reddy
21 Gerald Chouinard 37 Steve Kuffner 50 Ivan Reede
22 Carlos Cordeiro 38 Zhongding Lei 51 Shigenobu Sasaki
23 Charles Einolf 39 Lingjie Li 52 Cheng Shan
24 Wen Gao 40 Kyutae Lim 53 Steve Shellhammer
25 Monisha Ghosh 41 Jinnan Liu 54 Eli Sofer
26 Thomas Gurley 42 David Mazzarese 55 Carl Stevenson
27 Anh Twan Hoang 43 Apurva N. Mody 56 Victor Tawil
28 Wendong Hu 44 Peter Murray 57 JungSun Um
29 Sung Hyun Hwang 58 George Vlantis
30 Jerome J. Kalke 59 Jianfeng Wang
31 Ramon Khalona 60 Yonghong Zeng

62 The following members participated and voted on the development of IEEE Std. 802.22a-2014.

63 Apurva Mody, Chair
64 Chang-woo Pyo, Vice Chair

65 When this amendment was sent to sponsor ballot, the Task Group a had the following membership:

66 Ranga Reddy, Chair and Editor
68 Winston Caldwell 76 Hynduk Kang 83 Shigenobu Sasaki
69 Charles Einolf 77 Gwangzeen Ko 84 Steven Shellhammer
70 Peter Flynn 78 Bruce Kraemer 85 Chunyi Song
71 Tom Gurley 79 Donghun Lee 86 Victor Tawil
72 Hiroshi Harada 80 Liru Lu 87 Keat-Beng Toh
73 Bob Heile 81 Michael Lynch 88 Junyi Wang
74 Byng Jeong Jang 82 Paul Nikolich 89 Bing Xuan Zhao
75 Jerry Kalke 90 Xin (Amy) Zhang
92 Major contributions were received from the following individuals:
93 Gerald Chouinard 95 Sunghyun Hwang 98 Ranga Reddy
94 Charles Einolf 96 Gwangzeen Ko 99 Ivan Reede
97 Chang-woo Pyo
100
Copyright © 2019 IEEE. All rights reserved.
This is an unapproved IEEE Standards Draft, subject to change.
© IEEE 2021 – All rights reserved
---------------------- Page: 9 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Members participated and voted on the development of IEEE Std. 802.22b-2015.
2 Apurva Mody, Chair
3 Chang-woo Pyo, Vice Chair

4 When this amendment was sent to sponsor ballot, the Task Group b had the following membership:

5 Chang-woo Pyo, Chair and Editor
6 Sung Hyun Hwang, Vice Chair
7 Gabriel Villardi, Secretary
8 Gregory Buchwald 18 Jerome J. Kalke 28 Masayuki Oodo
9 Winston Caldwell 19 Hynduk Kang 29 Ranga K. Reddy
10 Gerald Chouinard 20 Gwangzeen Ko 30 Ivan Reede
11 Subir Das 21 Bruce Kraemer 31 Shigenobu Sasaki
12 Peter Flynn 22 Donghun Lee 32 Steve Shellhammer
13 Thomas Gurley 23 PinHsun Lin 33 Chunyi Song
14 Hiroshi Harada 24 Liru Lu 34 Keat-Beng Toh
15 Bob Heile 25 Michael Lynch 35 Xin (Amy) Zhang
16 Dien Hoang 26 Apurva Mody 36 Bing Xuan Zhao
17 Byung Jang Jeong 27 Paul Nikolich 37 Lei Zhongding
Copyright © 2019 IEEE. All rights reserved.
This is an unapproved IEEE Standards Draft, subject to change.
© IEEE 2021 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Introduction

2 This introduction is not part of P802.22/D6.0.0, Standard for Information Technology—

3 Local and Metropolitan Area Networks—
4 Specific requirements—
6 Part 22: Cognitive Radio Wireless Regional Area Network (WRAN) Medium Access
7 Control (MAC) and Physical Layer (PHY)
8 Specifications: Policies and Procedures for

9 Operation in the Bands that Allow Spectrum Sharing where the Communication Devices may Opportunistically

10 Operate in the Spectrum of the Primary Service
Copyright © 2019 IEEE. All rights reserved.
This is an unapproved IEEE Standards Draft, subject to change.
© IEEE 2021 – All rights reserved
---------------------- Page: 11 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

P802.22/D8.0.0, July 2019 Draft Standard for Information Technology—Telecommunications and information exchange

between systems Wireless Regional Area Networks (WRAN)—Specific requirements Part 22: Cognitive Wireless RAN

Medium Access Control (MAC) and Physical Layer (PHY) Specifications: Policies and Procedures for Operation in the TV

Bands
1 Contents

2 1. Overview ...................................................................................................................................................17

3 1.1 Scope ..................................................................................................................................................17

4 1.2 Purpose ...............................................................................................................................................17

5 1.3 Introduction ........................................................................................................................................17

6 2. Normative references .................................................
...

FINAL
INTERNATIONAL ISO /IEC/IEEE
DRAFT
STANDARD FDIS
8802-22
ISO/IEC JTC 1/SC 6
Telecommunications and information
Secretariat: KATS
exchange between systems — Wireless
Voting begins on:
2021-10-29 Regional Area Networks (WRAN) —
Specific requirements —
Voting terminates
2022- 03-18
Part 22:
Cognitive Wireless RAN Medium
Access Control (MAC) and Physical
Layer (PHY) Specifications: Policies
and procedures for operation in the
bands that allow spectrum sharing
where the communications devices
may opportunistically operate in the
spectrum of primary service
Télécommunications et échange d'information entre systèmes —
Réseaux régionaux sans fil (WRAN) — Exigences spécifiques —
Partie 22: Spécifications du contrôle d'accès du milieu sans fil cognitif
(MAC) et de la couche physique (PHY) : Politiques et procédures pour
le fonctionnement dans les bandes qui permettent le partage du
spectre, où les dispositifs de communication peuvent fonctionner de
manière opportuniste dans le spectre du service primaire
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/IEC/IEEE FDIS 8802-22:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © IEEE 2020
---------------------- Page: 1 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© IEEE 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from IEEE at the address below.

Institute of Electrical and Electronics Engineers, Inc
3 Park Avenue, New York
NY 10016-5997, USA
Email: [e-mail]
Website: www.ieee.org
Published in Switzerland
© IEEE 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Foreword

ISO (the International Organization for Standardization) and IEC (the International Electrotechnical

Commission) form the specialized system for worldwide standardization. National bodies that are

members of ISO or IEC participate in the development of International Standards through technical

committees established by the respective organization to deal with particular fields of technical activity.

ISO and IEC technical committees collaborate in fields of mutual interest. Other international

organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the

work.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO/IEC documents should be noted. This document was drafted in accordance with

the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives or

www.iec.ch/members_experts/refdocs).

IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating

Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its

standards through a consensus development process, approved by the American National Standards

Institute, which brings together volunteers representing varied viewpoints and interests to achieve the

final product. Volunteers are not necessarily members of the Institute and serve without compensation.

While the IEEE administers the process and establishes rules to promote fairness in the consensus

development process, the IEEE does not independently evaluate, test, or verify the accuracy of any of the

information contained in its standards.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details

of any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents) or the IEC list of patent

declarations received (see patents.iec.ch).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the World

Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),

see www.iso.org/iso/foreword.html. In the IEC, see www.iec.ch/understanding-standards.

ISO/IEC/IEEE 8802-22 was prepared by the LAN/MAN of the IEEE Computer Society (as IEEE Std

802.22-2019) and drafted in accordance with its editorial rules. It was adopted, under the “fast-track

procedure” defined in the Partner Standards Development Organization cooperation agreement between

ISO and IEEE, by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 6,

Telecommunications and information exchange between systems.

This second edition cancels and replaces the first edition (ISO/IEC/IEEE 8802-22:2015), which has been

technically revised.

A list of all parts in the ISO/IEC/IEEE 8802 series can be found on the ISO and IEC websites.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html and www.iec.ch/national-

committees.
© IEEE 2020 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

Abstract: This standard specifies the air interface, including the cognitive medium access control

layer (MAC) and physical layer (PHY), of point–to–multipoint wireless regional area networks

(WRANs) comprised of a professional fixed base station (BS) with fixed and portable user terminals

operating in the VHF/UHF TV broadcast bands between 54 MHz to 862 MHz, and potentially in the

1300 MHz to 1750 MHz, and 2700 MHz to 3700 MHz bands provided the regulatory regime allows

it.

Keywords: broadband wireless access network, cognitive radio, fixed user terminals,

IEEE 802.22™, portable user terminals, radio spectrum sensing, regional area network, WRAN

standards
The Institute of Electrical and Electronics Engineers, Inc.
3 Park Avenue, New York, NY 10016-5997, USA
Copyright © 2020 by The Institute of Electrical and Electronics Engineers, Inc.
d States of America.
All rights reserved. Published 5 May 2020. Printed in the Unite

IEEE and 802 are registered trademarks in the U.S. Patent & Trademark Office, owned by The Institute of

Electrical and Electronics Engineers, Incorporated.
Print: ISBN 978-1-5044-6148-1 STDPD23878
PDF: ISBN 978-1-5044-6147-4 STD23878
IEEE prohibits discrimination, harassment, and bullying.

For more information, visit http://www.ieee.org/web/aboutus/whatis/policies/p9-26.html.

No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission

of the publisher.
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 4 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Important Notices and Disclaimers Concerning IEEE Standards Documents

IEEE documents are made available for use subject to important notices and legal disclaimers. These notices

and disclaimers, or a reference to this page, appear in all standards and may be found under the heading

“Important Notices and Disclaimers Concerning IEEE Standards Documents.” They can also be obtained on

request from IEEE or viewed at http://standards.ieee.org/ipr/disclaimers.html.
Notice and Disclaimer of Liability Concerning the Use of IEEE Standards
Documents

IEEE Standards documents (standards, recommended practices, and guides), both full-use and trial-use, are

developed within IEEE Societies and the Standards Coordinating Committees of the IEEE Standards

Association (“IEEE SA”) Standards Board. IEEE (“the Institute”) develops its standards through a

consensus development process, approved by the American National Standards Institute (“ANSI”), which

brings together volunteers representing varied viewpoints and interests to achieve the final product. IEEE

Standards are documents developed through scientific, academic, and industry-based technical working

groups. Volunteers in IEEE working groups are not necessarily members of the Institute and participate

without compensation from IEEE. While IEEE administers the process and establishes rules to promote

fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the

accuracy of any of the information or the soundness of any judgments contained in its standards.

IEEE Standards do not guarantee or ensure safety, security, health, or environmental protection, or ensure

against interference with or from other devices or networks. Implementers and users of IEEE Standards

documents are responsible for determining and complying with all appropriate safety, security,

environmental, health, and interference protection practices and all applicable laws and regulations.

IEEE does not warrant or represent the accuracy or content of the material contained in its standards, and

expressly disclaims all warranties (express, implied and statutory) not included in this or any other

document relating to the standard, including, but not limited to, the warranties of: merchantability; fitness

for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness

of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort.

IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.”

Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there

are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to

the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and

issued is subject to change brought about through developments in the state of the art and comments

received from users of the standard.

In publishing and making its standards available, IEEE is not suggesting or rendering professional or other

services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any

other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his

or her own independent judgment in the exercise of reasonable care in any given circumstances or, as

appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE

standard.
IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO:
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE
UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND
REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 5 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Translations

The IEEE consensus development process involves the review of documents in English only. In the event

that an IEEE standard is translated, only the English version published by IEEE should be considered the

approved IEEE standard.
Official statements

A statement, written or oral, that is not processed in accordance with the IEEE SA Standards Board

Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its

committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures,

symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall

make it clear that his or her views should be considered the personal views of that individual rather than the

formal position of IEEE.
Comments on standards

Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of

membership affiliation with IEEE. However, IEEE does not provide consulting information or advice

pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a

proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a

consensus of concerned interests, it is important that any responses to comments and questions also receive

the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and

Standards Coordinating Committees are not able to provide an instant response to comments or questions

except in those cases where the matter has previously been addressed. For the same reason, IEEE does not

respond to interpretation requests. Any person who would like to participate in revisions to an IEEE

standard is welcome to join the relevant IEEE working group.
Comments on standards should be submitted to the following address:
Secretary, IEEE SA Standards Board
445 Hoes Lane
Piscataway, NJ 08854 USA
Laws and regulations

Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the

provisions of any IEEE Standards document does not imply compliance to any applicable regulatory

requirements. Implementers of the standard are responsible for observing or referring to the applicable

regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not

in compliance with applicable laws, and these documents may not be construed as doing so.

Copyrights

IEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws.

They are made available by IEEE and are adopted for a wide variety of both public and private uses. These

include both use, by reference, in laws and regulations, and use in private self-regulation, standardization,

and the promotion of engineering practices and methods. By making these documents available for use and

adoption by public authorities and private users, IEEE does not waive any rights in copyright to the

documents.
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 6 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Photocopies

Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to

photocopy portions of any individual standard for company or organizational internal use or individual, non-

commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center,

Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; [phone]. Permission to

photocopy portions of any individual standard for educational classroom use can also be obtained through

the Copyright Clearance Center.
Updating of IEEE Standards documents

Users of IEEE Standards documents should be aware that these documents may be superseded at any time

by the issuance of new editions or may be amended from time to time through the issuance of amendments,

corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the

document together with any amendments, corrigenda, or errata then in effect.

Every IEEE standard is subjected to review at least every 10 years. When a document is more than 10 years

old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of

some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that

they have the latest edition of any IEEE standard.

In order to determine whether a given document is the current edition and whether it has been amended

through the issuance of amendments, corrigenda, or errata, visit IEEE Xplore at http://ieeexplore.ieee.org/ or

contact IEEE at the address listed previously. For more information about the IEEE SA or IEEE’s standards

development process, visit the IEEE SA Website at http://standards.ieee.org.
Errata

Errata, if any, for IEEE standards can be accessed via https://standards.ieee.org/standard/index.html. Search

for standard number and year of approval to access the web page of the published standard. Errata links are

located under the Additional Resources Details section. Errata are also available in IEEE Xplore: https://

ieeexplore.ieee.org/browse/standards/collection/ieee/. Users are encouraged to periodically check for errata.

Patents

Attention is called to the possibility that implementation of this standard may require use of subject matter

covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the

existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has

filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE

SA Website at https://standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate

whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or

under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair

discrimination to applicants desiring to obtain such licenses.

Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not

responsible for identifying Essential Patent Claims for which a license may be required, for conducting

inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or

conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing

agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that

determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their

own responsibility. Further information may be obtained from the IEEE Standards Association.

Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 7 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Participants

The following is a list of participants in the Wireless Regional Area Networks Working Group:

Apurva N. Mody, Chair
Oliver Holland, Vice Chair
Ranga K. Reddy, Lead Editor
Subir Das Gianfranco Miele Paul Nikolich
Robert F. Heile Steve Shellhammer
Historical participants

At the time this standard was submitted to the IEEE SA for approval, the following voting members had

participated in the IEEE P802.22 Working Group until December 2011:
Apurva N. Mody, Chair
Gerald Chouinard, Vice Chair and Lead Editor
Kyu Hwan An Wen Gao Bruce Kraemer
Ingo Gaspard
Chee Wei Ang Steve Kuffner
Kwok Shum Au Monisha Ghosh Denis Kuwahara
Mark Austin Joanna Guenin Chang-Ho Lee
Anuj Batra Jin Guo Geunho Lee
Thomas Gurley
John Benko Haeyoung Lee
Robert Berger JaeSong Han Jeong Suk Lee
Dagnachew Birru Hiroshi Harada Zhongding Lei
Scott Blue Ahren Hartman Wing Seng Leon
Robert F. Heile Barry Lewis
Monique Bourgeois Brown
Gregory Buchwald Anh Twan Hoang Lingjie Li
Winston Caldwell Michael Hoghooghi Ying-Chang Liang
Ed Callaway Mark Hopkins Euntack Lim
Dave Cavalcanti Victor Hou Kyutae Lim
Kiran Challapali Wendong Hu Jiezhen Lin
Soo-Young Chang Junhong Hui Hang Liu
Duckdong Hwang Jinnan Liu
Remi Chayer
Shiuh Yuan Chen Sung Hyun Hwang Michael Lynch
Tao Chen Tae–In Hyon Steve Mace
Jinxia Cheng Yutaka Ikeda David Magee
Soon Ik Jeon Ben Manny
Aik Chindapol
InHwan Choi Baowei Ji David Mazzarese
Liwen Chu Ravi Kalavakunta Tony Morella
Joon–Hwa Chun Jerome J. Kalke Peter Murray
Chris Clanton Bub-Joo Kang Max Muterspaugh
Charles Cook Mark Kelley Mullaguru Naidu
Charles Cooper Ramon Khalona Paul Nikolich
John Notor
Carlos Cordeiro Thomas Kiernan
Subir Das Byoung–Jo Kim Moh Nouroozian
W. Carl Day Chang-Joo Kim Seungmok Oh
Upkar Dhaliwal HakSun Kim Barry O’Mahony
Ashish Pandharipande
Johnny Dixon Kihong Kim
Peter Ecclesine Sangbum Kim Juha Pihlaja
Charles Einolf Gwangzeen Ko Patrick Pirat
Michael Fischer Tom Kolze Ron Porat
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 8 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Jeff Poston Dave Silk JungSun Um
Jim Raab Kirk Skeba George Vlantis
Lei Wang
Mohammad Rahman Douglas Smith
Jianfeng Wang
Ranga K. Reddy Eli Sofer
Yunbiao Wang
Ivan Reede Myung Sun Song
Tom Wasilewski
Edgar Reihl Srikathyayani Srikanteswara
Alfred Wieczorek
Jon Walter Rosdahl Jayne Stancavage
Kelly Williams
William Rose Carl Stevenson
Yuchun Wu
Luis Escobar Sanz William Stiles
Shiquan WuBo Xia
Shigenobu Sasaki Hideki Tanaka
Changlong Xu
Jeffrey Schiffer Clifford Tavares
ShanShan Xu
Chris Seagren Victor Tawil
Steve Yao
Alireza Seyedi Shawn Taylor
Yonghong Zeng
Cheng Shan Paul Thompson
Jianwei Zhang
Steve Shellhammer James Tomcik
Xin Zhang
Major contributions to this standard were made by the following individuals:
Kwok Shum Au Ramon Khalona Ashish Pandharipande
John Benko Thomas Kiernan Patrick Pirat
Kak-Sun Kim
Winston Caldwell Mohammad Rahman
Dave Cavalcanti Kihong Kim Ranga K. Reddy
Soo-Young Chang Sangbum Kim Ivan Reede
Gerald Chouinard Gwangzeen Ko Shigenobu Sasaki
Carlos Cordeiro Steve Kuffner Cheng Shan
Charles Einolf Zhongding Lei Steve Shellhammer
Wen Gao Lingjie Li Eli Sofer
Monisha Ghosh Kyutae Lim Carl Stevenson
Thomas Gurley Jinnan Liu Victor Tawil
Anh Twan Hoang David Mazzarese JungSun Um
Wendong Hu Apurva N. Mody George Vlantis
Sung Hyun Hwang Peter Murray Jianfeng Wang
Jerome J. Kalke Mogh Nouroozian Yonghong Zeng

The following members participated and voted on the development of IEEE Std 802.22a™-2014:

Apurva N. Mody, Chair
Chang-woo Pyo, Vice Chair

When this amendment was sent to sponsor ballot, the Task Group a had the following membership:

Ranga K. Reddy, Chair and Editor
Winston Caldwell Hynduk Kang Shigenobu Sasaki
Charles Einolf Gwangzeen Ko Steven Shellhammer
Peter Flynn Bruce Kraemer Chunyi Song
Tom Gurley Donghun Lee Victor Tawil
Hiroshi Harada Liru Lu Keat-Beng Toh
Robert F. Heile Michael Lynch Junyi Wang
Byng Jeong Jang Paul Nikolich Bing Xuan Zhao
Jerry Kalke Xin (Amy) Zhang
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 9 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Major contributions were received from the following individuals:
Gerald Chouinard Sunghyun Hwang Ranga K. Reddy
Ivan Reede
Charles Einolf Gwangzeen Ko
Chang-woo Pyo

The following members participated and voted on the development of IEEE Std 802.22b™-2015:

Apurva N. Mody, Chair
Chang–woo Pyo, Vice Chair

When this amendment was sent to sponsor ballot, the Task Group b had the following membership:

Chang–woo Pyo, Chair and Editor
Sung Hyun Hwang, Vice Chair
Gabriel Villardi, Secretary
Gregory Buchwald Jerome J. Kalke Masayuki Oodo
Hynduk Kang Ranga K. Reddy
Winston Caldwell
Gerald Chouinard Gwangzeen Ko Ivan Reede
Subir Das Bruce Kraemer Shigenobu Sasaki
Peter Flynn Donghun Lee Steve Shellhammer
Thomas Gurley PinHsun Lin Chunyi Song
Hiroshi Harada Liru Lu Keat–Beng Toh
Robert F. Heile Michael Lynch Xin (Amy) Zhang
Dien Hoang Apurva N. Mody Bing Xuan Zhao
Byung Jang Jeong Paul Nikolich Lei Zhongding

The following members of the individual balloting committee voted on this standard. Balloters may have

voted for approval, disapproval, or abstention.
Thomas Alexander Robert F. Heile Ronald Murias
Richard Alfvin Marco Hernandez Charles Ngethe
Amelia Andersdotter Werner Hoelzl
Nick S. A. Nikjoo
Atsushi Ito
Butch Anton Paul Nikolich
Raj Jain
Stefan Aust Bansi Patel
Harry Bims SangKwon Jeong Walter Pienciak
Kenneth Bow Pranav Jha Clinton Powell
Nancy Bravin Jerome Kalke Venkatesha Prasad
Vern Brethour Piotr Karocki R. K. Rannow
Demetrio Bucaneg Jr. Stuart Kerry Ranga K. Reddy
William Byrd Evgeny Khorov Maximilian Riegel
C. Caicedo Bastidas Yongbum Kim Naotaka Sato
Paul Cardinal Jan Kruys Thomas Starai
Juan Carreon Thomas Kurihara Walter Struppler
Pin Chang Alexander Lackpour David Tepen
Todor Cooklev Hyeong Ho Lee David Thompson
Alistair Duffy Michael Lynch Mark–Rene Uchida
Michael Fischer Bruce Mackie Lisa Ward
Avraham Freedman Jeffery Masters Scott Willy
Zhigang Gong Stephen McCann Andreas Wolf
Randall Groves
Apurva N. Mody Oren Yuen
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 10 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)

When the IEEE SA Standards Board approved this standard on 5 September 2019, it had the following

membership:
Gary Hoffman, Chair
Ted Burse, Vice Chair
Jean-Philippe Faure, Past Chair
Konstantinos Karachalios, Secretary
Masayuki Ariyoshi David J. Law Annette D. Reilly
Stephen D. Dukes Joseph Levy Dorothy Stanley
Sha Wei
J. Travis Griffith Howard Li
Xiaohui Liu Phil Wennblom
Guido Hiertz
Kevin Lu Philip Winston
Christel Hunter
Daleep Mohla Howard Wolfman
Joseph L. Koepfinger*
Feng Wu
Andrew Myles
Thomas Koshy
Jingyi Zhou
John D. Kulick
*Member Emeritus
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 11 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Introduction

This introduction is not part of IEEE Std 802.22–2019, IEEE Standard for Information Technology—

Telecommunications and information exchange between systems—Wireless Regional Area Networks (WRAN)

Specific requirements—Part 22: Cognitive Wireless RAN Medium Access Control (MAC) and Physical Layer

(PHY) Specifications: Policies and Procedures for Operation in the Bands that Allow Spectrum Sharing where the

Communications Devices May Opportunistically Operate in the Spectrum of Primary Service.

This standard specifies the air interface, including the cognitive radio MAC and PHY, of point-to-multipoint

and backhaul WRANs comprised of a professional fixed BS with fixed and portable user terminals. The

standard specifies operation in the bands that allow spectrum sharing where the communications devices

may opportunistically operate in the spectrum of the primary service, such as the VHF/UHF TV broadcast

bands between 54 MHz to 862 MHz, and the 1300 MHz to 1750 MHz and 2700 MHz to 3700 MHz bands

provided the regulatory regime allows it.
Copyright © 2020 IEEE. All rights reserved.
---------------------- Page: 12 ----------------------
ISO/IEC/IEEE FDIS 8802-22:2021(E)
Contents

1. Overview............................................................................................................................................ 15

1.1 Scope...................................................................................................................................... 15

1.2 Purpose................................................................................................................................... 15

1.3 Introduction............................................................................................................................ 16

1.4 Word usage ............................................................................................................................ 19

2. Normative references......................................................................................................................... 20

3. Definitions ......................................................................................................................................... 22

4. Abbreviations and acronyms ............................................................................................................. 30

5. System architecture............................................................................................................................ 36

5.1 Reference architecture ........................................................................................................... 36

5.2 Management reference architecture....................................................................................... 40

6. Packet Convergence sublayer ............................................................................................................ 44

6.1 MAC SDU format.................................................................................................................. 44

6.2 Classification ......................................................................................................................... 44

6.3 IEEE 802.3/Ethernet-specific part ......................................................................................... 46

6.4 IP specific part ....................................................................................................................... 47

7. MAC Common Part sublayer ............................................................................................................ 48

7.1 General................................................................................................................................... 48

7.2 Addressing and connections ..................................................................

...