83.080 - Plastics
Plastics
Kunststoffe
Plastiques
Polimerni materiali
General Information
This document specifies a system for sampling procedures for testing plastics waste and recyclates which take into account the specifics of the plastics waste and recyclates. It is intended to cover all stages of the plastic recycling process.
The sampling procedures include the statistical specifics of the plastic waste and the behaviour of recyclates.
The sampling method is expected to produce a representative testing sample. Differences can arise due to:
- the mixture of plastics;
- the o...view more
- Technical specification20 pagesEnglish language
sale 10% off- e-Library read for1 day
This document describes and classifies a range of laboratory ignition sources for use in fire tests on plastics and products consisting substantially of plastics. These sources vary in intensity and area of impingement. They are suitable for use to simulate the initial thermal abuse to which plastics are potentially exposed in certain actual fire risk scenarios. This compilation of standard ignition sources describes the ignition sources used by different standards development organizations and ...view more
- Draft37 pagesEnglish language
sale 15% off- Standard37 pagesEnglish language
sale 15% off- Draft40 pagesEnglish language
sale 15% off
This document specifies a method for the determination of the ultimate anoxic biodegradability of plastics made of organic compounds, where the amount of the produced nitrogen and carbon dioxide at the end of the test is measured.
The test substance is exposed to an inoculum stemming from the denitrification tank of a wastewater treatment plant. Testing is performed under defined laboratory conditions.
- Standard32 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft33 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies a laboratory test method for determining the degree and rate of the aerobic biodegradation level of plastic materials. Biodegradation of plastic materials is determined by measuring the oxygen demand in a closed respirometer when exposed to seawater sampled from coastal areas under laboratory conditions. The conditions described in this document might not always correspond to the optimum conditions for the maximum degree of biodegradation, however this test method is desi...view more
- Standard12 pagesEnglish language
sale 15% off- Draft12 pagesEnglish language
sale 15% off- Draft12 pagesEnglish language
sale 15% off
This document specifies a laboratory test method for determining the degree and rate of the aerobic biodegradation level of plastic materials. Biodegradation is determined by measuring the CO2 evolved from plastic materials when exposed to seawater sampled from coastal areas under laboratory conditions. The conditions described in this document might not always correspond to the optimum conditions for the maximum degree of biodegradation, however this test method is designed to give an indicatio...view more
- Standard16 pagesEnglish language
sale 15% off- Draft16 pagesEnglish language
sale 15% off- Draft15 pagesEnglish language
sale 15% off
This document specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of PS-I moulding and extrusion materials. It establishes the requirements
for handling test material and for conditioning both the test material before moulding and the
specimens before testing.
This document gives procedures and conditions for the preparation of test specimens and procedures
for measuring properties of the materials from which these specimens a...view more
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft11 pagesEnglish language
sale 10% off- e-Library read for1 day
This document establishes a system of designation for polystyrene thermoplastic material, which can
be used as the basis for specifications.
The types of polystyrene plastics are differentiated from each other by a classification system based on
appropriate levels of the designatory properties:
a) Vicat softening temperature, and
b) melt mass-flow rate.
and on information about the intended application and/or method of processing, important properties,
additives and colorants, fillers and...view more
- Standard13 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft10 pagesEnglish language
sale 10% off- e-Library read for1 day
This document establishes a method for measurement of specific heat capacity, cp, using temperature modulated differential scanning calorimetry.
- Standard14 pagesEnglish language
sale 15% off- Draft13 pagesEnglish language
sale 15% off
This document gives a brief overview of the current (2019) situation in plastic recycling systems, relevant existing standards and short description of different recycling techniques. It aims to identify the necessity of standards in the plastics recycling system and give direction for the adoption of regional standards and/or the development of new and existing standards. This document addresses various recycling options, with focus on, but not limited to, mechanical recycling, chemical and/or ...view more
- Technical report24 pagesEnglish language
sale 15% off- Draft24 pagesEnglish language
sale 15% off
This document specifies a test method for the determination of abrasive wear resistance of plastics using abrasive material on a reciprocating motion. It also specifies calculation method for specific wear rate.
- Standard14 pagesEnglish language
sale 15% off- Draft9 pagesEnglish language
sale 15% off
This document specifies the method of testing the knowledge and skill of a welder who is required to carry out welds on thermoplastics in new constructions and repair work.
The skill examination of a welder is an essential condition for the assurance of the quality of the welding work.
The application of this document guarantees that the examination is carried out according to a uniform test procedure.
This document applies when the contractor or the authorities responsible for the applicatio...view more
- Standard47 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft46 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PS-I moulding and extrusion materials. It establishes the requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing. This document gives procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are ma...view more
- Standard8 pagesFrench language
sale 15% off- Standard8 pagesEnglish language
sale 15% off- Standard8 pagesFrench language
sale 15% off- Draft8 pagesEnglish language
sale 15% off
This document specifies requirements and guidelines for the quantification and reporting of the process carbon footprint of biobased plastics (see ISO 22526-1), being a partial carbon footprint of a bioplastic product, based on ISO 14067 and consistent with International Standards on life cycle assessment (ISO 14040 and ISO 14044). This document is applicable to process carbon footprint studies (P-CFP) of plastic materials, being a partial carbon footprint of a product, whether or not the result...view more
- Standard10 pagesEnglish language
sale 15% off- Draft10 pagesEnglish language
sale 15% off
This document establishes a system of designation for polystyrene thermoplastic material, which can be used as the basis for specifications. The types of polystyrene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties: a) Vicat softening temperature, and b) melt mass-flow rate. and on information about the intended application and/or method of processing, important properties, additives and colorants, fillers and reinfo...view more
- Standard7 pagesFrench language
sale 15% off- Standard6 pagesEnglish language
sale 15% off- Standard7 pagesFrench language
sale 15% off- Draft6 pagesEnglish language
sale 15% off
This document specifies two methods for the determination of the surface tension of polymer dispersions and rubber latices (natural and synthetic). — Method A is the ring method (Du Noüy ring method). — Method B is the plate method (Wilhelmy plate method). Method A is suitable valid for polymer dispersions and rubber latices with a viscosity less than 200 mPa·s. Method B is not suitable for polymer dispersions and rubber latices containing cationic surfactants. Methods A and B are also suitable ...view more
- Standard12 pagesEnglish language
sale 15% off- Standard13 pagesFrench language
sale 15% off- Draft12 pagesEnglish language
sale 15% off
This document describes a test method to determine the activation energy (Ea) of photochemical degradation reactions in accelerated weathering tests according to the Arrhenius model in the most comprehensive manner.
- Standard17 pagesEnglish language
sale 15% off- Draft17 pagesEnglish language
sale 15% off
1.1 This document specifies conditions for the determination of the reduced viscosity (also known
as viscosity number) and K-value of PVC resins. It is applicable to resins in powder form which consist
of homopolymers of the monomer vinyl chloride and copolymers, terpolymers, etc., of vinyl chloride
with one or more other monomers, but where vinyl chloride is the main constituent. The resins may
contain small amounts of unpolymerized substances (e.g. emulsifying or suspending agents, catalys...view more
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft19 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies two two-cavity moulds, the type D11 and D12 ISO moulds, for the injection
moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type D11) or
2 mm (type D12), which can be used for a variety of tests. The moulds can additionally be fitted with
inserts for studying the effects of weld lines on the mechanical properties (see Annex A).
- Standard16 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft12 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies a test method to determine the degree and rate of aerobic biodegradation of
plastic materials when settled on marine sandy sediment at the interface between seawater and the
seafloor, by measuring the evolved carbon dioxide (CO2). This test method can also be applied to other
solid materials.
This test method is a simulation under laboratory conditions of the habitat found in different seawater/
sediment-areas in the sea, e.g. in a benthic zone where sunlight reaches...view more
- Standard20 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft17 pagesEnglish language
sale 10% off- e-Library read for1 day
This document establishes a system of designation for poly(methyl methacrylate) (PMMA) thermoplastic
material, which can be used as the basis for specifications.
The types of PMMA plastic are differentiated from each other by a classification system based on
appropriate levels of the designatory properties:
a) Vicat softening temperature;
b) melt mass-flow rate;
c) viscosity number (optional);
and on information about the intended application and/or method of processing, important propert...view more
- Standard13 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft9 pagesEnglish language
sale 10% off- e-Library read for1 day