Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 24026-1:2020)

This document establishes a system of designation for poly(methyl methacrylate) (PMMA) thermoplastic
material, which can be used as the basis for specifications.
The types of PMMA plastic are differentiated from each other by a classification system based on
appropriate levels of the designatory properties:
a) Vicat softening temperature;
b) melt mass-flow rate;
c) viscosity number (optional);
and on information about the intended application and/or method of processing, important properties,
additives and colorants.
This document is applicable to all poly(methyl methacrylate) homopolymers and to copolymers of
methyl methacrylate (MMA) containing at least a mass percentage of 80 % of MMA and not more than a
mass percentage of 20 % of acrylic esters or other monomers.
This document applies to materials ready for normal use in the form of beads, granules and pellets and
to materials unmodified or modified by colorants, additives, etc. It does not apply to PMMA modified
with elastomers.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This document does not provide engineering data, performance data or data on
processing conditions which might be required to specify a material for a particular application and/or
method of processing.
If such additional properties are required, they are, if suitable, determined using the test methods
specified in ISO 24026-2.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements can be given in data block 5 (see 4.1).

Kunststoffe - Polymethylmethacrylat (PMMA)-Werkstoffe - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 24026-1:2020)

In diesem Dokument ist ein Bezeichnungssystem für thermoplastische Polymethylmethacrylat (PMMA) Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
Die PMMA-Kunststoff-Typen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften:
a) Vicat-Erweichungstemperatur;
b) Schmelze-Massefließrate (MFR, en: melt mass-flow rate);
c) Viskositätszahl (freigestellt);
und Informationen über die vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive und Farbstoffe beruht.
Dieses Dokument ist für alle Homopolymere von Polymethylmethacrylaten und Copolymere von Methylmethacrylat (MMA) anwendbar, die mindestens einen Massenanteil von 80 % MMA und nicht mehr als einen Massenanteil von 20 % Acrylester oder sonstige Monomere enthalten.
Dieses Dokument gilt für gebrauchsfertige Werkstoffe in Form von Perlen, Granulat oder Pellets und für mit Farbstoffen, Additiven usw. modifizierte oder nicht modifizierte Werkstoffe. Es gilt nicht für PMMA, die mit Elastomeren modifiziert sind.
Dies soll nicht implizieren, dass Werkstoffe mit der gleichen Bezeichnung zwangsläufig das gleiche Leistungsverhalten aufweisen. Dieses Dokument enthält keine technischen Daten, Leistungsangaben oder Verarbeitungsbedingungen, die für die Spezifikation eines Werkstoffes für eine bestimmte Anwendung und/oder Verarbeitungsart erforderlich sein könnten.
Falls derartige zusätzliche Eigenschaften gefordert sind, werden diese, falls zutreffend, nach den in ISO 24026 2 festgelegten Prüfverfahren bestimmt.
Um einen thermoplastischen Werkstoff für eine bestimmte Anwendung festzulegen oder um eine reproduzierbare Verarbeitung sicherzustellen, können im Daten-Block 5 (siehe 4.1) zusätzliche Anforderungen angegeben werden.

Plastiques - Matériaux à base de poly(méthacrylate de méthyle) (PMMA) pour moulage et extrusion - Partie 1: Système de désignation et base de spécifications (ISO 24026-1:2020)

Le présent document établit un système de désignation des matériaux thermoplastiques à base de poly(méthacrylate de méthyle) (PMMA) qui peut être utilisé comme base pour les spécifications.
Les types de plastiques PMMA sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation:
a) température de ramollissement Vicat;
b) indice de fluidité à chaud en masse;
c) indice de viscosité (facultatif);
et des informations concernant l'application prévue et/ou la méthode de mise en œuvre, les propriétés importantes, les additifs et les colorants.
Le présent document est applicable à tous les homopolymères de poly(méthacrylate de méthyle) et à tous les copolymères de méthacrylate de méthyle (MMA) contenant un pourcentage en masse d'au moins 80 % de MMA et d'au plus 20 % d'esters acryliques ou d'autres monomères.
Le présent document s'applique aux matériaux prêts à l'emploi dans le cadre d'une utilisation normale sous forme de perles, grains et granulés et aux matériaux modifiés ou non par des colorants, des additifs, etc. Il ne s'applique pas aux PMMA modifiés par des élastomères.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. Le présent document ne comporte pas de données sur la conception, la performance ou les conditions de mise en œuvre qui pourraient être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en œuvre particulière.
Si de telles caractéristiques supplémentaires sont nécessaires, elles sont déterminées en utilisant les méthodes d'essai spécifiées dans l'ISO 24026‑2, s'il y a lieu.
Afin de spécifier un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en œuvre reproductible, des exigences supplémentaires peuvent être codées dans le bloc de données 5 (voir 4.1).

Polimerni materiali - Materiali na osnovi polimetilmetakrilata (PMMA) za oblikovanje in ekstrudiranje - 1. del: Sistem označevanja in podlage za specifikacije (ISO 24026-1:2020)

General Information

Status
Published
Public Enquiry End Date
16-Jun-2019
Publication Date
09-Jul-2020
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2020
Due Date
05-Sep-2020
Completion Date
10-Jul-2020

RELATIONS

Buy Standard

Standard
SIST EN ISO 24026-1:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 24026-1:2020
01-oktober-2020
Nadomešča:
SIST EN ISO 8257-1:2006
Polimerni materiali - Materiali na osnovi polimetilmetakrilata (PMMA) za
oblikovanje in ekstrudiranje - 1. del: Sistem označevanja in podlage za
specifikacije (ISO 24026-1:2020)

Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1:

Designation system and basis for specifications (ISO 24026-1:2020)

Kunststoffe - Polymethylmethacrylat (PMMA)-Werkstoffe - Teil 1: Bezeichnungssystem

und Basis für Spezifikationen (ISO 24026-1:2020)

Plastiques - Matériaux à base de poly(méthacrylate de méthyle) (PMMA) pour moulage

et extrusion - Partie 1: Système de désignation et base de spécifications (ISO 24026-

1:2020)
Ta slovenski standard je istoveten z: EN ISO 24026-1:2020
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 24026-1:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 24026-1:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 24026-1:2020
EN ISO 24026-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 8257-1:2006
English Version
Plastics - Poly(methyl methacrylate) (PMMA) moulding
and extrusion materials - Part 1: Designation system and
basis for specifications (ISO 24026-1:2020)

Plastiques - Matériaux à base de poly(méthacrylate de Kunststoffe - Polymethylmethacrylat (PMMA)-

méthyle) (PMMA) pour moulage et extrusion - Partie 1: Werkstoffe - Teil 1: Bezeichnungssystem und Basis für

Système de désignation et base de spécifications (ISO Spezifikationen (ISO 24026-1:2020)

24026-1:2020)
This European Standard was approved by CEN on 21 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24026-1:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24026-1:2020
EN ISO 24026-1:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 24026-1:2020
EN ISO 24026-1:2020 (E)
European foreword

This document (EN ISO 24026-1:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics"

in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by

NBN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by December 2020, and conflicting national standards

shall be withdrawn at the latest by December 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 8257-1:2006.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 24026-1:2020 has been approved by CEN as EN ISO 24026-1:2020 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 24026-1:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 24026-1:2020
INTERNATIONAL ISO
STANDARD 24026-1
First edition
2020-05
Plastics — Poly(methyl methacrylate)
(PMMA) moulding and extrusion
materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux à base de poly(méthacrylate de méthyle)
(PMMA) pour moulage et extrusion —
Partie 1: Système de désignation et base de spécifications
Reference number
ISO 24026-1:2020(E)
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 24026-1:2020
ISO 24026-1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24026-1:2020
ISO 24026-1:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 2

4 Designation system ............................................................................................................................................................................................ 2

4.1 General ........................................................................................................................................................................................................... 2

4.2 Data block 1 ............................................................................................................................................................................................... 2

4.3 Data block 2 ............................................................................................................................................................................................... 2

4.4 Data block 3 ............................................................................................................................................................................................... 3

4.5 Data block 4 ............................................................................................................................................................................................... 3

4.5.1 General...................................................................................................................................................................................... 3

4.5.2 Vicat softening temperature .................................................................................................................................. 3

4.5.3 Melt flow rate ...................................................................................................................................................................... 4

4.5.4 Viscosity number (optional) .................................................................................................................................. 4

4.6 Data block 5 ............................................................................................................................................................................................... 5

5 Examples of designations ............................................................................................................................................................................ 5

Bibliography ................................................................................................................................................................................................................................ 6

© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24026-1:2020
ISO 24026-1:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rule
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.