83.160.99 - Other tyres
Other tyres
Reifen fur weitere Fahrzeuge
Autres pneumatiques
Druge pnevmatike
General Information
This document specifies the main requirements, including designations, dimensions and markings, of the metric series of rubber solid tyres for pneumatic tyre rims primarily intended for industrial machines for use on prepared surfaces. Rim contours fitting these tyres are specified in ISO 3739-1 and ISO 3739-3.
- Standard6 pagesEnglish language
sale 15% off- Standard6 pagesFrench language
sale 15% off
ISO 4250-1:2017 specifies designations and dimensions for earth-mover tyres and gives the recommended rims primarily intended for earth-moving machinery as defined in ISO 6165. The ISO 4250 series consists of three parts which specify the technical elements relating to designation and dimensions of tyres and rims for earth-movers; it also gives load tables for these tyres.
- Standard26 pagesFrench language
sale 15% off- Standard23 pagesEnglish language
sale 15% off
The ISO 4250 series consists of three parts laying down the technical designation and dimensions of tyres and rims for earth-movers; it also gives load tables for these tyres. ISO 4250-2:2017 gives working definitions of masses and load cycles and specifies tyre loads and reference inflation pressures for narrow- and wide-base tyres primarily intended for earth-mover machines.
- Standard26 pagesEnglish language
sale 15% off- Standard25 pagesFrench language
sale 15% off
ISO 10571:2016 specifies the designation, dimensions, load ratings and reference speed for tyres and rims fitted to vehicles, such as all-terrain equipment, mobile cranes, crash tenders, etc., likely to operate on highway over long distances at reference speed and under constant load.
- Standard9 pagesFrench language
sale 15% off- Standard9 pagesFrench language
sale 15% off- Standard9 pagesEnglish language
sale 15% off
ISO 3739-1:2007 specifies the main requirements of the metric series of pneumatic tyres primarily intended for industrial vehicles, including designations, dimensions and markings. The tyres are based on the following parameters: speeds not exceeding 50 km/h; use on 5° tapered or flat base rims. The conversion of code-designated industrial tyres into metric-designated tyres is outside the scope of ISO 3739-1:2007.
- Standard12 pagesFrench language
sale 15% off- Standard12 pagesEnglish language
sale 15% off
- Draft12 pagesFrench language
sale 15% off- Draft12 pagesEnglish language
sale 15% off
- Draft21 pagesEnglish language
sale 15% off- Draft23 pagesEnglish language
sale 15% off- Draft26 pagesFrench language
sale 15% off
- Draft4 pagesEnglish language
sale 15% off
ISO 13442:2004 sets the designation, dimensions, load ratings and reference speeds for tyres and rims fitted to construction machines (backhoe loaders, small dumpers, loaders, excavators etc.) operating on building sites under loading and transport conditions.
- Standard12 pagesFrench language
sale 15% off- Standard12 pagesEnglish language
sale 15% off
- Standard5 pagesEnglish language
sale 15% off- Standard5 pagesFrench language
sale 15% off
Applies to tyres primarily intended for industrial vehicles for use on prepared surfaces (counterbalanced lift trucks, side loaders, and other vehicles). Defines a reference load-carrying capacity which the load rating is based on.
- Standard2 pagesEnglish language
sale 15% off- Standard2 pagesFrench language
sale 15% off- Standard2 pagesFrench language
sale 15% off
Specifies the main requirements of the metric series of tyres. Gives the tyre designations to be used. Tabulates the ratings needed.
- Standard5 pagesFrench language
sale 15% off- Standard5 pagesFrench language
sale 15% off- Standard5 pagesEnglish language
sale 15% off