ASTM F1159-16
(Practice)Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards
Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards
SIGNIFICANCE AND USE
3.1 This practice provides designers/engineers of amusement rides and devices not addressed in the other ASTM Committee F24 standards with design references and criteria to use in design development.
SCOPE
1.1 This practice establishes information and procedures for the design of amusement rides and devices and major modifications to amusement rides and devices which the designer/engineer identifies as outside the purview of other ASTM F24 design standards.
1.1.1 Prior to designating an amusement ride or device as outside the purview of other ASTM F24 standards and subject to Practice F1159, the designer/engineer shall perform a review of all standards under the jurisdiction of the ASTM Committee F24 addressing amusement ride and device design and determine that Practice F1159 is appropriate and more applicable to the amusement ride or device than other ASTM Committee F24 practices addressing amusement ride and device design.
1.1.2 In making such a determination, the designer/engineer shall consider the following:
1.1.2.1 The general nature of the amusement ride or device;
1.1.2.2 The absence of relevant specific requirements or features addressed by other ASTM Committee F24 practices.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1159 − 16
Standard Practice for
Design of Amusement Rides and Devices that are Outside
1
the Purview of Other F24 Design Standards
This standard is issued under the fixed designation F1159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
3
1. Scope 2.2 Federal Document:
OSHA 29 CFR Fall Protection Systems Criteria and Prac-
1.1 This practice establishes information and procedures for
tices Part 1926.502 (d)
the design of amusement rides and devices and major modifi-
cations to amusement rides and devices which the designer/
3. Significance and Use
engineer identifies as outside the purview of other ASTM F24
3.1 This practice provides designers/engineers of amuse-
design standards.
ment rides and devices not addressed in the other ASTM
1.1.1 Prior to designating an amusement ride or device as
Committee F24 standards with design references and criteria to
outside the purview of other ASTM F24 standards and subject
use in design development.
toPracticeF1159,thedesigner/engineershallperformareview
of all standards under the jurisdiction of theASTM Committee
4. General Design Requirements
F24 addressing amusement ride and device design and deter-
mine that Practice F1159 is appropriate and more applicable to
4.1 Design and Calculations—Basic documentation and
the amusement ride or device than other ASTM Committee
engineering analysis shall be in accordance with Practice
F24 practices addressing amusement ride and device design.
F2291.
1.1.2 In making such a determination, the designer/engineer
4.2 Drawings and Records—Records shall be kept in accor-
shall consider the following:
dance with Practice F2291.
1.1.2.1 The general nature of the amusement ride or device;
4.3 Testing—Document and record the testing performance
1.1.2.2 The absence of relevant specific requirements or
of amusement rides and devices in accordance with the tests
features addressed by other ASTM Committee F24 practices.
given in Practice F1193.
1.2 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
DESIGN PROCEDURES
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
5. Patron Restraint, Clearance Envelope, and
bility of regulatory limitations prior to use.
Containment Design Criteria
5.1 Patron restraint, clearance envelope, and containment
2. Referenced Documents
design criteria shall be in accordance with Section 6 of Practice
2
2.1 ASTM Standards:
F2291.
F1193 Practice for Quality, Manufacture, and Construction
of Amusement Rides and Devices
6. Amusement Ride and Device Structures Fastening,
F2291 Practice for Design ofAmusement Rides and Devices
Mechanical Systems and Components, Fall Protection,
F2374 Practice for Design, Manufacture, Operation, and
Adhesive Bonding, and Coatings
Maintenance of Inflatable Amusement Devices
6.1 Structures shall be designed in accordance with the
provisions of Practice F2291, Section 8.
1
6.2 Welding—Welding and welding procedures shall be in
This practice is under the jurisdiction ofASTM Committee F24 on Amusement
Rides and Devices and is the direct responsibility of Subcommittee F24.24 on
accordance with the provisions of Practice F2291, Section 15.
Design and Manufacture.
6.3 Fasteners—Fasteners shall de designed in accordance
Current edition approved Dec. 15, 2016. Published January 2017. Originally
approved in 1988. Last previous edition approved in 2015 as F1159 – 15b. DOI:
with the provisions of Practice F2291, Section 16.
10.1520/F1159-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Superintendent of Documents, U.S. Government Printing
the ASTM website. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1159 − 16
6.4 MechanicalSystemsandComponents—Mechanical sys- 11. Brakes
tems and components shall be designed in accordance with the
11.1 When used, brakes shall be designed in accordance
provisions of Practice F2291, Section 13.
with Practice F2291, subsection 13.7.
6.5 Fixed Air Supported Structures—Fixed air supported
structures shall be in accordance with subsection 8.36 of 12. Machine Guards
Practice F2291.
12.1 Machine guards shall be designed in accordance with
6.6 Fall Protection—Fall pro
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1159 − 15b F1159 − 16
Standard Practice for
Design of Amusement Rides and Devices that are Outside
1
the Purview of Other F24 Design Standards
This standard is issued under the fixed designation F1159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice establishes information and procedures for the design of amusement rides and devices and major modifications
to amusement rides and devices which the designer/engineer identifies as outside the purview of other ASTM F24 design standards.
1.1.1 Prior to designating an amusement ride or device as outside the purview of other ASTM F24 standards and subject to
Practice F1159, the designer/engineer shall perform a review of all standards under the jurisdiction of the ASTM Committee F24
addressing amusement ride and device design and determine that Practice F1159 is appropriate and more applicable to the
amusement ride or device than other ASTM Committee F24 practices addressing amusement ride and device design.
1.1.2 In making such a determination, the designer/engineer shall consider the following:
1.1.2.1 The general nature of the amusement ride or device;
1.1.2.2 The absence of relevant specific requirements or features addressed by other ASTM Committee F24 practices.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
F1193 Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices
F2291 Practice for Design of Amusement Rides and Devices
F2374 Practice for Design, Manufacture, Operation, and Maintenance of Inflatable Amusement Devices
3
2.2 Federal Document:
OSHA 29 CFR Fall Protection Systems Criteria and Practices Part 1926.502 (d)
3. Significance and Use
3.1 This practice provides designers/engineers of amusement rides and devices not addressed in the other ASTM Committee
F24 standards with design references and criteria to use in design development.
4. General Design Requirements
4.1 Design and Calculations—Basic documentation and engineering analysis shall be in accordance with Practice F2291.
4.2 Drawings and Records—Records shall be kept in accordance with Practice F2291.
4.3 Testing—Document and record the testing performance of amusement rides and devices in accordance with the tests given
in Practice F1193.
1
This practice is under the jurisdiction of ASTM Committee F24 on Amusement Rides and Devices and is the direct responsibility of Subcommittee F24.24 on Design
and Manufacture.
Current edition approved Nov. 1, 2015Dec. 15, 2016. Published November 2015January 2017. Originally approved in 1988. Last previous edition approved in 2015 as
F1159 – 15a.F1159 – 15b. DOI: 10.1520/F1159-15B.10.1520/F1159-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1159 − 16
DESIGN PROCEDURES
5. Patron Restraint, Clearance Envelope, and Containment Design Criteria
5.1 For rides and devices having a ride vehicle or passenger carrier, the patron Patron restraint, clearance envelope, and
containment design criteria shall be in accordance with Section 6 of Practice F2291, to the extent that these requirements are
applicable as determined by the ride analysis and patron restraint and containment analysis.
5.2 For devices lacking a ride vehicle or passenger carrier, consideration shall be given to measures that prevent or mitigate
injuries potentially caused by collisions as determined by the ride analysis and patron restraint and containment analysis.
6. Amusement Ride and Device Structures Fastening, Mechanical Systems and Components, Fall Protection, Adhesive
Bonding, and Coatings
6.1 St
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.