ASTM B69-01

Standard Specification for Rolled Zinc

SCOPE
1.1 This specification covers two types of commercial rolled zinc as described in 1.2. It should be understood that the specification is general. Any closer limitations on permissible variations shall be a matter of agreement between the supplier (manufacturer) and the purchaser.
1.2 Rolled zinc is furnished in two types as follows:
1.2.1 Type I - Coils or sheets cut from strip (ribbon) rolled zinc and
1.2.2 Type II - Zinc plates such as boiler and hull plates produced by any rolling method.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Nov-2001
• ICS: 77.120.60 - Lead, zinc, tin and their alloys
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.04 - Zinc and Cadmium

Relations

• Replaces: ASTM B69-98ae2 - Standard Specification for Rolled Zinc
• Effective Date: 10-Nov-2001
• Replaced By: ASTM B69-01e1 - Standard Specification for Rolled Zinc
• Effective Date: 10-Nov-2001
• Referred By: ASTM B949-23 - Standard Specification for General Requirements for Zinc and Zinc Alloy Products
• Effective Date: 10-Nov-2001
• Referred By: ASTM C1861-23 - Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster
• Effective Date: 10-Nov-2001
• Referred By: ASTM F3160-21 - Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants
• Effective Date: 10-Nov-2001
• Referred By: ASTM C1047-19 - Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
• Effective Date: 10-Nov-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: B 69 – 01
Standard Specification for
1
Rolled Zinc
This standard is issued under the fixed designation B 69; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (e) indicates an editorial change since the last revision or reapproval.
5
1. Scope Alloys for Determination of Chemical Composition
E 60 Practice for Molecular Absorption Spectrometric
1.1 This specification covers two types of commercial rolled
Methods for Chemical Analysis of Metals, Ores, and
zinc as described in 1.2. It should be understood that the
5
Related Materials
specification is general. Any closer limitations on permissible
E 88 Practice for Sampling Nonferrous Metals and Alloys
variations shall be a matter of agreement between the supplier
5
in Cast Form for Determination of Chemical Composition
(manufacturer) and the purchaser.
3
E 384 Test Method for Microhardness of Materials
1.2 Rolled zinc is furnished in two types as follows:
6
E 527 Practice for Numbering Metals and Alloys (UNS)
1.2.1 TypeI- Coils or sheets cut from strip (ribbon) rolled
E 536 Test Method for Chemical Analysis of Zinc and Zinc
zinc and
7
Alloys
1.2.2 Type II - Zinc plates such as boiler and hull plates
E 634 Practice for Sampling of Zinc and Zinc Alloys for
produced by any rolling method.
7
Optical Emission Spectrometric Analysis
1.3 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
3. Terminology
information only.
3.1 Terms shall be defined in accordance with Terminology
1.4 This standard does not purport to address all of the
B 899.
safety concerns, if any, associated with its use. It is the
3.2 Definitions of Terms Specific to This Standard:
responsibility of the user of this standard to become familiar
3.2.1 coiled sheet—sheet coils with either slit or unslit
with all hazards including those identified in the appropriate
edges.
Material Data Sheet for this product/material as provided by
3.2.2 flat sheet—sheet with sheared, slit, or sawed edges
the manufacturer, to establish appropriate safety and health
that has been flattened or leveled.
practices, and determine the applicability of regulatory limi-
3.2.3 plate—rolled product, rectangular in cross section and
tations prior to use.
form, or thickness of more than 0.125 in. (3.175 mm) with
2. Referenced Documents either untrimmed, sheared or sawed edges.
3.2.4 rolled zinc, n—wrought zinc or zinc alloy sheet, strip,
2.1 The issue of each of the following reference documents
or plate produced by hot and/or cold rolling.
shall be that which is current on the date the purchase order is
3.2.5 sheet—rolled product, rectangular in cross section and
accepted by the supplier (manufacturer).
form of thickness of 0.003 in. (0.076 mm) through 0.125 in.
2.2 ASTM Standards:
(3.175 mm) with sheared, slit, untrimmed or sawed edges.
B 899 Terminology Relating to Non-ferrous Metals and
2
Alloys
4. Ordering Information
3
E 8 Test Methods for Tension Testing of Metallic Materials
4.1 Orders for materials under this specification shall in-
E 18 Test Methods for Rockwell Hardness and Rockwell
3 clude the following information:
Superficial Hardness of Metallic Materials
4.1.1 ASTM designation and year of issue,
E 29 Practice for Using Significant Digits in Test Data to
4 4.1.2 Quantity (weight),
Determine Conformance with Specifications
4.1.3 Name of material (rolled zinc),
E 55 Practice for Sampling Wrought Nonferrous Metals and
4.1.4 Type of rolled zinc,
4.1.5 Dimensions (thickness, width, length, or coil),
1
This specification is under the jurisdiction of ASTM Committee B02 on
4.1.6 Chemical composition/alloy, and
Nonferrous Metals and Alloysand is the direct responsibility of Subcommittee
4.1.7 Others as agreed upon between the purchaser and the
B02.04 on Zinc and Cadmium.
Current edition approved May 10, 2001. Published July 2001. Originally
supplier.
e2
published as B 69-26. Last previous edition B 69-98a .
2
Annual Book of ASTM Standards, Vol 02.04.
3
Annual Book of ASTM Standards, Vol 03.01.
5
Annual Book of ASTM Standards, Vol 03.05.
4
Annual Book of ASTM Standards, Vol 14.02.
6
Annual Book of ASTM Standards, Vol 01.01.
7
Annual Book of ASTM Standards, Vol 03.06.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B69
5. Materials and Manufacture 7.1.2 The testing of zinc for hardness shall be made on a
Rockwell superficial hardness tester set up for the 15T scale, in
5.1 The supplier (manufacturer) shall ensure that each rolled
accordance with Test Methods E 18, or on a
...