ASTM F1733-07
(Specification)Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ABSTRACT
This specification covers polyamide (PA) butt fusion fittings for use with polyamide pipe (IPS and ISO) and tubing (CTS). This specification covers butt fusion fittings intended for use with polyamide pipe and tubing. Fittings covered by this specification are normally molded. Fittings may be machined from extruded or molded stock. Conditioning, dimensions and tolerances, short-term rupture strength, sustained pressure test, and minimum hydrostatic burst pressure test shall be performed to conform with the requirements specified.
SCOPE
1.1 This specification covers polyamide (PA) butt fusion fittings for use with polyamide pipe (IPS and ISO) and tubing (CTS). Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.
1.2 &inch-pound-units;
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1733 −07 AnAmerican National Standard
Standard Specification for
Butt Heat Fusion Polyamide(PA) Plastic Fitting for
1
Polyamide(PA) Plastic Pipe and Tubing
This standard is issued under the fixed designation F1733; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 Federal Standard:
4
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
1.1 This specification covers polyamide (PA) butt fusion
2.3 Military Standard:
fittings for use with polyamide pipe (IPS and ISO) and tubing
4
MIL-STD-129 Marking for Shipment and Storage
(CTS). Included are requirements for materials, workmanship,
2.4 National Sanitation Foundation Standard:
dimensions, marking, sustained pressure, and burst pressure.
Standard No. 14 for Plastic Piping Components and Related
1.2 The values stated in inch-pound units are to be regarded 5
Materials
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
3. Terminology
and are not considered standard.
3.1 Definitions are in accordance with Terminology F412
1.3 This standard does not purport to address all of the
and abbreviations are in accordance with Terminology D1600,
safety concerns, if any, associated with its use. It is the
unless otherwise specified.
responsibility of the user of this standard to establish appro-
3.2 dimension ratio (DR) for thermoplastic pipe—the ratio
priate safety and health practices and determine the applica-
of diameter to wall thickness. For this specification it is
bility of regulatory limitations prior to use.
calculated by dividing the specified outside diameter by the
specified wall thickness of the fitting at its area of fusion. DRs
2. Referenced Documents
are rounded and do not calculate exactly.
2
2.1 ASTM Standards:
4. Classification
D1598 Test Method for Time-to-Failure of Plastic Pipe
Under Constant Internal Pressure 4.1 General—This specification covers butt fusion fittings
D1599 Test Method for Resistance to Short-Time Hydraulic intended for use with polyamide pipe and tubing.
Pressure of Plastic Pipe, Tubing, and Fittings 4.1.1 Fittings covered by this specification are normally
D1600 Terminology forAbbreviatedTerms Relating to Plas- molded. Fittings may be machined from extruded or molded
tics stock.
D2122 Test Method for Determining Dimensions of Ther- 4.1.2 Fittings fabricated by thermal welding are not in-
moplastic Pipe and Fittings cluded in this specification.
D2513 Specification for Thermoplastic Gas Pressure Pipe, 4.1.3 Fittings intended for use in the distribution of natural
Tubing, and Fittings gas or petroleum fuels shall also meet the requirements of
Specification D2513.
D4066 Classification System for Nylon Injection and Extru-
3
sion Materials (PA) (Withdrawn 2012)
5. Ordering Information
F412 Terminology Relating to Plastic Piping Systems
5.1 When ordering fittings under this specification, the
following should be specified:
1 5.1.1 Polyamide compound (material designation or trade
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. name)
Current edition approved Nov. 1, 2007. Published November 2007. Originally
5.1.2 Style of fitting (tee, 90° ell, and the like)
approved in 1996. Last previous edition approved in 2002 as F1733–06(2002). DOI:
5.1.3 Size:
10.1520/F1733-07.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
3 5
The last approved version of this historical standard is referenced on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
www.astm.org. Arbor, MI 48113-0140, http://www.nsf.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1733−07
TABLE 1 IPS Sizing System Outside Diameters and Tolerances
5.1.3.1 Nominal diameter.
for Fittings for Use with Polyamide Pipe, in.
5.1.3.2 CTS, IPS, or schedule.
Nominal Pipe Average Outside Diameter
5.1.3.3 Dimension ratio number or schedule number.
Tolerance
A
Size at Area of Fusion
6. Materials
1
⁄2 0.840 ±0.008
3
⁄4 1.050 ±0.008
6.1 Basic Materials—Thisspecificationcoversfittingsmade
1 1.315 ±0.010
from polyamide plastics
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 1733–96 (Reapproved 2002) Designation: F 1733 – 07
Standard Specification for
Butt Heat Fusion Polyamide(PA) Plastic Fitting for
1
Polyamide(PA) Plastic Pipe and Tubing
This standard is issued under the fixed designation F 1733; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers polyamide (PA) butt fusion fittings for use with polyamide pipe (IPS and ISO) and tubing (CTS).
Included are requirements for materials, workmanship, dimensions, marking, sustained pressure, and burst pressure.
1.2The values given in parentheses are provided for information only.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D 1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D 2513 Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
D 4066 Classification System for Nylon Injection and Extrusion Materials (PA)
F 412 Terminology Relating to Plastic Piping Systems
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
MIL-STD-129 Marking for Shipment and Storage
2.4 National Sanitation Foundation Standard:
4
Standard No. 14 for Plastic Piping Components and Related Materials
3. Terminology
3.1 DefinitionsareinaccordancewithTerminologyF 412andabbreviationsareinaccordancewithTerminologyD 1600,unless
otherwise specified.
3.2 dimension ratio (DR) for thermoplastic pipe—the ratio of diameter to wall thickness. For this specification it is calculated
by dividing the specified outside diameter by the specified wall thickness of the fitting at its area of fusion. DRs are rounded and
do not calculate exactly.
4. Classification
4.1 General—This specification covers butt fusion fittings intended for use with polyamide pipe and tubing.
4.1.1 Fittings covered by this specification are normally molded. Fittings may be machined from extruded or molded stock.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Sept. 10, 1996. Published November 1996.
Current edition approved Nov. 1, 2007. Published November 2007. Originally approved in 1996. Last previous edition approved in 2002 as F 1733–06(2002).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
, Vol 08.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 08.01.
3
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
4
Annual Book of ASTM Standards, Vol 08.02.
4
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1733 – 07
4.1.2 Fittings fabricated by thermal welding are not included in this specification.
4.1.3 Fittings intended for use in the distribution of natural gas or petroleum fuels shall also meet the requirements of
Specification D 2513.
5. Ordering Information
5.1 When ordering fittings under this specification, the following should be specified:
5.1.1 Polyamide compound (material designation or trade name)
5.1.2 Style of fitting (tee, 90° ell, and the like)
5.1.3 Size:
5.1.3.1 Nomi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.