Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

ABSTRACT
This specification establishes requirements for sulfone plastic insert fittings utilizing a copper crimp ring for SDR9 cross-linked polyethylene (PEX) tubing for cold- and hot-water distribution systems. Material for fitting shall be molded from sulfone plastic. Molded part shall not crack, split, or shatter and be free of visible splay. Fittings shall be tested for performance requirements such as hydrostatic burst, hydrostatic sustained pressure strength, thermocycling, excessive temperature-pressure capability, dimensions, workmanship, finish, appearance, assembly, crimp joint, and insert crush test.
SCOPE
1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes (3/8 , 1/2 , and 3/4 and 1) of cross-linked polyethylene (PEX) tubing that meet the requirements for Specification F876 and polyethylene of raised temperature (PE-RT) tubing that meet the requirements of Specifications F2623 and F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.  
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following is an index of the appendix in this specification:    
GO/NO-GO Crimp Gauges  
Appendix X1  
1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2014
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM F2159-14 - Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM F2159-14 - Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2159 −14 An American National Standard
Standard Specification for
Plastic Insert Fittings Utilizing a Copper Crimp Ring for
SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9
1
Polyethylene of Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F2159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic
1.1 This specification establishes requirements for sulfone
Pressure of Plastic Pipe, Tubing, and Fittings
plastic insert fittings and copper crimp rings for four sizes
D1600 Terminology forAbbreviatedTerms Relating to Plas-
3 1 3
( ⁄8, ⁄2, and ⁄4 and 1) of cross-linked polyethylene (PEX)
tics
tubing that meet the requirements for Specification F876 and
D2122 Test Method for Determining Dimensions of Ther-
polyethylene of raised temperature (PE-RT) tubing that meet
moplastic Pipe and Fittings
the requirements of Specifications F2623 and F2769. These
D6394 Specification for Sulfone Plastics (SP)
fittings are intended for use in 100 psi (690 kPa) cold- and
F412 Terminology Relating to Plastic Piping Systems
hot-water distribution systems operating at temperatures up to
F876 SpecificationforCrosslinkedPolyethylene(PEX)Tub-
and including 180°F (82°C). Included are the requirements for
ing
material, molded part properties, performance, workmanship,
F1498 Specification for Taper Pipe Threads 60° for Thermo-
dimensions, and markings to be used on the fittings and rings.
plastic Pipe and Fittings
1.2 Units—The values stated in inch-pound units are to be
F1807 Specification for Metal Insert Fittings Utilizing a
regarded as standard. The values given in parentheses are
Copper Crimp Ring for SDR9 Cross-linked Polyethylene
mathematical conversions to SI units that are provided for
(PEX) Tubing and SDR9 Polyethylene of Raised Tem-
information only and are not considered standard.
perature (PE-RT) Tubing
1.3 The following is an index of the appendix in this
F2623 Specification for Polyethylene of RaisedTemperature
specification:
(PE-RT) SDR 9 Tubing
GO/NO-GO Crimp Gauges Appendix X1
F2769 Specification for Polyethylene of RaisedTemperature
1.4 The following precautionary caveat pertains only to the
(PE-RT) Plastic Hot and Cold-Water Tubing and Distri-
test method portions, Sections 11 and 12, of this specification.
bution Systems
This standard does not purport to address all of the safety
2.2 ASME Standard:
concerns, if any, associated with its use. It is the responsibility
3
B 1.20.1 Pipe Threads General Purpose Inch
of the user of this standard to establish appropriate safety and
2.3 NSF International Standard:
health practices and determine the applicability of regulatory
ANSI/NSF Standard No. 14 for Plastic Piping Components
requirements prior to use.
4
and Related Materials
2. Referenced Documents
ANSI/NSF Standard No. 61 for Drinking Water System
4
2
Components-Health Effects
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
3. Terminology
D1598 Test Method for Time-to-Failure of Plastic Pipe
3.1 Definitions—Definitions are in accordance with Termi-
nology F412 and abbreviations are in accordance with Termi-
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
nology D1600, unless otherwise indicated.
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved Aug. 1, 2014. Published September 2014. Originally
approved 2001. Last previous edition approved in 2011 as F2159-11. DOI:
10.1520/F2159-14.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
the ASTM website. Arbor, MI 48113-0140, http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2159−14
4. Classification 7.2 Hydrostatic Burst—Assemblies shall meet the minimum
hydrostatic burst requirements shown in Table 1, when tested
4.1 This specification governs one class of fittings and
in accordance with 11.5.
3 1 3
copper crimp rings suitable for use with no
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2159 − 11 F2159 − 14 An American National Standard
Standard Specification for
Plastic Insert Fittings Utilizing a Copper Crimp Ring for
SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9
1
Polyethylene of Raised Temperature (PE-RT) Tubing
This standard is issued under the fixed designation F2159; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes
3 1 3
( ⁄8, ⁄2, and ⁄4 and 1) of cross-linked polyethylene (PEX) plastic tubing an tubing that meet the requirements for Specification F876
and polyethylene of raised temperature (PE-RT) tubing. tubing that meet the requirements of Specifications F2623 and F2769.
These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to
and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship,
dimensions, and markings to be used on the fittings and rings.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following is an index of the appendix in this specification:
colwidth="2.78in"/COLSPECCOLSPEC/align="center" colname="col2" colwidth="0.22in"/COLSPEC
GO/NO-GO Crimp Gauges Appendix X1
1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements
prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D6394 Specification for Sulfone Plastics (SP)
F412 Terminology Relating to Plastic Piping Systems
F876 Specification for Crosslinked Polyethylene (PEX) Tubing
F877 Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
F1498 Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
F1807 Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing
and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
F2623 Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing
F2769 Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution
Systems
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved April 15, 2011Aug. 1, 2014. Published April 2011September 2014. Originally approved 2001. Last previous edition approved in 20102011 as
F2159-10.-11. DOI: 10.1520/F2159-11.10.1520/F2159-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2159 − 14
2.2 ASME Standard:
3
B 1.20.1 Pipe Threads General Purpose Inch
2.3 NSF International Standard:
4
ANSI/NSF Standard No. 14 for Plastic Piping Components and Related Materials
4
ANSI/NSF Standard No. 61 for Drinking Water System Components-Health Effects
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology
D
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.