ASTM B704-03(2009)
(Specification)Standard Specification for Welded UNS N06625, UNS N06219 and UNS N08825 Alloy Tubes
Standard Specification for Welded UNS N06625, UNS N06219 and UNS N08825 Alloy Tubes
ABSTRACT
This specification covers welded tubes made of UNS N06625, UNS N06219 and UNS N08825 alloys for use in boilers, heat exchangers and condensers for general corrosion prevention in either low or high-temperature environments. This standard contains information on manufacturing, chemical composition, mechanical properties and dimensional requirements for the welded tubes.
SCOPE
1.1 This specification covers welded UNS N06625, UNS N06219 and UNS N08825 alloy boiler, heat exchanger, and condenser tubes for general corrosion resisting and low or high-temperature service.
1.2 This specification covers tubes 1/8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to 12.70 mm), inclusive, in wall thickness. Specification B 751 lists the dimensional requirements of these sizes. Tubes having other dimensions may be furnished provided such tubing complies with all other requirements of this specification.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B704 −03(Reapproved 2009)
Standard Specification for
Welded UNS N06625, UNS N06219 and UNS N08825 Alloy
Tubes
This standard is issued under the fixed designation B704; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3.1.1 Quantity (feet or number of lengths),
3.1.2 UNS number,
1.1 This specification covers welded UNS N06625, UNS
3.1.3 Size (outsize diameter, minimum or average wall
N06219 and UNS N08825 alloy boiler, heat exchanger, and
thickness),
condenser tubes for general corrosion resisting and low or
3.1.4 Length (random or specific),
high-temperature service.
3.1.5 Class, and
1.2 This specification covers tubes ⁄8 to 5 in. (3.18 to 127
3.1.6 Grade if UNS N06625 is specified. If neither grade of
mm),inclusive,inoutsidediameterand0.015to0.500in.(0.38
N06625 is specified, grade 1 will be supplied.
to 12.70 mm), inclusive, in wall thickness. Specification B751
3.1.7 ASTM designation.
lists the dimensional requirements of these sizes. Tubes having
3.1.8 Product Analysis—State if required.
other dimensions may be furnished provided such tubing
3.1.9 Certification—State if a certification or a report of test
complies with all other requirements of this specification.
results is required.
1.3 The values stated in inch-pound units are to be regarded 3.1.10 Purchaser Inspection—State which tests or inspec-
tions are to be witnessed, if any.
as the standard. The values given in parentheses are for
information only.
4. Materials and Manufacture
1.4 This standard does not purport to address all of the
4.1 Tube shall be made from flat-rolled alloy by an auto-
safety concerns, if any, associated with its use. It is the
matic welding process with no addition or filler metal. Subse-
responsibility of the user of this standard to become familiar
quent to welding and prior to final annealing, the material shall
with all hazards including those identified in the appropriate
be cold-worked in either the weld metal only or both weld and
Material Safety Data Sheet (MSDS) for this product/material
base metal.
as provided by the manufacturer, to establish appropriate
safety and health practices, and determine the applicability of
4.2 Tube shall be furnished with oxide removed. When
regulatory limitations prior to use.
bright annealing is used, descaling is not necessary.
2. Referenced Documents
5. Chemical Composition
2.1 ASTM Standards:
5.1 The material shall conform to the composition limits
B751 Specification for General Requirements for Nickel and
specified in Table 1. One test is required for each lot as defined
Nickel Alloy Welded Tube
in Specification B751.
E8 Test Methods for Tension Testing of Metallic Materials
5.2 If a product analysis is performed, it shall meet the
3. Ordering Information chemistry limits prescribed in Table 1, subject to the analysis
tolerances of Specification B751.
3.1 Orders for material to this specification should include
the following information:
6. Mechanical and Other Properties
6.1 Mechanical Properties—The material shall conform to
This specification is under the jurisdiction of ASTM Committee B02 on
the mechanical property requirements specified in Table 2. One
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
test is required for each lot as defined in Specification B751.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2009. Published October 2009. Originally
6.2 Flattening Test—Aflattening test shall be made on each
approved in 1982. Last previous edition approved in 2003 as B704– 03. DOI:
end of one tube per lot. Superficial ruptures resulting from
10.1520/B0704-03R09.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or surface imperfections shall not be cause for rejection.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.3 Flange Test—Aflange test shall be made on each end of
Standards volume information,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B704–00 Designation: B 704 – 03 (Reapproved 2009)
Standard Specification for
Welded UNS N06625, UNS N06219 and UNS N08825 Alloy
Tubes
This standard is issued under the fixed designation B 704; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers welded UNS N06625, UNS N06219 and UNS N08825 alloy boiler, heat exchanger, and condenser
tubes for general corrosion resisting and low or high-temperature service.
1.2 This specification covers tubes ⁄8 to 5 in. (3.18 to 127 mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38 to
12.70 mm), inclusive, in wall thickness. Specification B 751 lists the dimensional requirements of these sizes. Tubes having other
dimensions may be furnished provided such tubing complies with all other requirements of this specification.
1.3 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
B 751 Specification for General Requirements for Nickel and Nickel Alloy Welded Tube
E8 Test Methods for Tension Testing of Metallic Materials
3. Ordering Information
3.1 Orders for material to this specification should include the following information:
3.1.1 Quantity (feet or number of lengths),
3.1.2 UNS number,
3.1.3 Size (outsize diameter, minimum or average wall thickness),
3.1.4 Length (random or specific),
3.1.5 Class, and
3.1.6ASTM designation.
3.1.7
3.1.6 Grade if UNS N06625 is specified. If neither grade of N06625 is specified, grade 1 will be supplied.
3.1.7 ASTM designation.
3.1.8 Product Analysis—State if required.
3.1.8
3.1.9 Certification—State if a certification or a report of test results is required.
3.1.9
3.1.10 Purchaser Inspection—State which tests or inspections are to be witnessed, if any.
4. Materials and Manufacture
4.1 Tube shall be made from flat-rolled alloy by an automatic welding process with no addition or filler metal. Subsequent to
welding and prior to final annealing, the material shall be cold-worked in either the weld metal only or both weld and base metal.
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved May 10, 2000. Published June 2000. Originally published as B704–82. Last previous edition B704–96.
Current edition approved Oct. 1, 2009. Published October 2009. Originally approved in 1982. Last previous edition approved in 2003 as B 704 - 03.
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
B 704 – 03 (2009)
4.2 Tube shall be furnished with oxide removed. When bright annealing is used, descaling is not necessary.
5. Chemical Composition
5.1 The material shall conform to the composition limits specified in Table 1. One test is required for each lot as defined in
Specification B 751.
5.2 If a product analysis is performed, it shall meet the chemistry limits prescribed in Table 1, subject to the analys
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.