ASTM B476-01(2017)

Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials

ABSTRACT
This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. The raw material shall be of such quality and purity that the finished product shall have the properties and characteristics prescribed in the applicable product specification. The product shall be produced by a combination of hot or cold working operations, it shall be finished, unless otherwise specified, by cold working, annealing, or heat treatment as may be necessary to meet the specified properties. Surfaces of all material furnished to this specification shall be smooth, clean, and free from scratches, stains, rough spots, slivers, laps, scale, pits, and any other injurious defects. Test methods such as chemical analysis and physical tests shall be performed accordingly.
SIGNIFICANCE AND USE
11.1 For purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with Practice E29.    
Property  
Unit  
Rounded Unit
for Observed or
Calculated Value  
Chemical composition  
percent  
Hardness
Knoop (100-g load unless other-
wise specified)
Vicker (specify load)
Rockwell (all scales, specify which)
Rockwell superficial (all scales,
specify which)  
nearest unit on the last right
hand place of figure of
specified limit  
Resistivity  
μΩ·cm  
Tensile strength  
psi (MPa)  
nearest 1000 psi (nearest 10
MPa)    
Yield Strength  
psi (MPa)  
nearest 1000 psi (nearest
10 MPa)  
Elongation  
Below 5 %  
percent  
nearest multiple of 0.5 %  
5 % and over  
percent  
nearest 1 %  
Grain size  
Up to 0.055 mm incl.  
mm  
nearest multiple of 0.005
mm    
Over 0.055 to 0.160, mm, incl.  
mm  
nearest 0.01 mm
SCOPE
1.1 This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. Unless otherwise specified in the purchase order or in an individual specification, these general requirements shall apply to wrought electrical contact materials where indicated in the applicable product specifications issued by ASTM.  
1.2 In case of conflict, the requirements on the purchase order, the individual specification, and this general specification shall prevail in the sequence named.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2017
• ICS: 77.120.99 - Other non-ferrous metals and their alloys
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.05 - Precious Metals and Electrical Contact Materials and Test Methods

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B476 −01(Reapproved 2017)
Standard Specification for
General Requirements for Wrought Precious Metal Electrical
1
Contact Materials
This standard is issued under the fixed designation B476; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
2
1. Scope 2.2 ASTM Standards:
B63Test Method for Resistivity of Metallically Conducting
1.1 This specification covers general requirements common
Resistance and Contact Materials
to wrought precious metal electrical contact alloy products in
B772Guide for Specifying the Chemical Compositions for
the form of sheet, strip, wire, and rod. Unless otherwise
Electrical Contact Materials (Arcing and Nonarcing)
specifiedinthepurchaseorderorinanindividualspecification,
E3Guide for Preparation of Metallographic Specimens
these general requirements shall apply to wrought electrical
E8Test Methods for Tension Testing of Metallic Materials
contact materials where indicated in the applicable product
E29Practice for Using Significant Digits in Test Data to
specifications issued by ASTM.
Determine Conformance with Specifications
1.2 In case of conflict, the requirements on the purchase
E55Practice for Sampling Wrought Nonferrous Metals and
order, the individual specification, and this general specifica-
Alloys for Determination of Chemical Composition
tion shall prevail in the sequence named.
E112Test Methods for Determining Average Grain Size
1.3 The values stated in inch-pound units are to be regarded E384Test Method for Microindentation Hardness of Mate-
rials
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
3. Terminology
and are not considered standard.
3.1 Definitions:
1.4 This standard does not purport to address all of the
3.1.1 lot, n—the quantity of material of the same type, size,
safety concerns, if any, associated with its use. It is the
andfinishproducedatonetimefromthesamecastorheat,and
responsibility of the user of this standard to become familiar
heat treated in the same heat-treatment cycle.
with all hazards including those identified in the appropriate
Safety Data Sheet (SDS) for this product/material as provided
4. Ordering Information
by the manufacturer, to establish appropriate safety and health
practices, and determine the applicability of regulatory limi-
4.1 Ordersformaterialtothisspecificationshallincludethe
tations prior to use.
following information:
1.5 This international standard was developed in accor-
4.1.1 Designation and revision date of this specification.
dance with internationally recognized principles on standard-
4.1.1.1 Ifarevisiondateisnotdesignated,thelatestrevision
ization established in the Decision on Principles for the
should be used.
Development of International Standards, Guides and Recom-
4.1.2 Designation and revision date of the applicable prod-
mendations issued by the World Trade Organization Technical
uct specification.
Barriers to Trade (TBT) Committee.
4.1.2.1 Ifarevisiondateisnotdesignated,thelatestrevision
of the product specification should be used.
2. Referenced Documents
4.1.3 Description of material form,
2.1 The following documents of the issue in effect, on the
4.1.4 Dimensions of the material,
date of material purchase, form a part of this specification to 4.1.5 Total quantity of each size,
the extent referenced herein:
4.1.6 Temper of the material (annealed, cold worked, etc.),
4.1.7 Temper test (hardness or tensile) (Section 10),
1
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
2
B02.05 on Precious Metals and Electrical Contact Materials. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2017. Published April 2017. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1968. Last previous edition approved in 2012 as B476–01(2012). Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/B0476-01R17. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B476−01(2017)
4.1.8 Special requirements (if any), and 6.4.1 The thickness tolerances shall be those prescribed in
4.1.9 Certification (Section 14). Table 3.
6.4.2 The width standard tolerance for slit products shall be
4.2 Specify the following, i
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B476 − 01 (Reapproved 2012) B476 − 01 (Reapproved 2017)
Standard Specification for
General Requirements for Wrought Precious Metal Electrical
1
Contact Materials
This standard is issued under the fixed designation B476; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers general requirements common to wrought precious metal electrical contact alloy products in the
form of sheet, strip, wire, and rod. Unless otherwise specified in the purchase order or in an individual specification, these general
requirements shall apply to wrought electrical contact materials where indicated in the applicable product specifications issued by
ASTM.
1.2 In case of conflict, the requirements on the purchase order, the individual specification, and this general specification shall
prevail in the sequence named.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices,
and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 The following documents of the issue in effect, on the date of material purchase, form a part of this specification to the extent
referenced herein:
2
2.2 ASTM Standards:
B63 Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials
B772 Guide for Specifying the Chemical Compositions for Electrical Contact Materials (Arcing and Nonarcing)
E3 Guide for Preparation of Metallographic Specimens
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E112 Test Methods for Determining Average Grain Size
E384 Test Method for Microindentation Hardness of Materials
3. Terminology
3.1 Definitions:
3.1.1 lot, n—the quantity of material of the same type, size, and finish produced at one time from the same cast or heat, and
heat treated in the same heat-treatment cycle.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.05 on
Precious Metals and Electrical Contact Materials.
Current edition approved May 1, 2012April 1, 2017. Published May 2012April 2017. Originally approved in 1968. Last previous edition approved in 20062012 as
B476 – 01 (2006).(2012). DOI: 10.1520/B0476-01R12.10.1520/B0476-01R17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B476 − 01 (2017)
4. Ordering Information
4.1 Orders for material to this specification shall include the following information:
4.1.1 Designation and revision date of this specification.
4.1.1.1 If a revision date is not designated, the latest revision should be used.
4.1.2 Designation and revision date of the applicable product specification.
4.1.2.1 If a revision date is not designated, the latest revision of the product specification should be used.
4.1.3 Description
...