ASTM D7530/D7530M-17

Standard Specification for Self-Adhesive Glass Fiber Fabric Reinforced Polymer Modified Asphalt Steep Slope Roll Roofing Surfaced with Mineral Granules

ABSTRACT
This specification covers prefabricated, self-adhesive, glass fiber fabric reinforced, polymer-modified asphalt roll roofing, with granule surfacing, designed for steep slope applications. These products use polymer modifiers in their top and bottom coatings and have an adhesive bottom layer which is exposed by removal of a peel-away protective release paper or film sheet. The specified tests and property limits used to characterize the sheet materials are intended to establish minimum, or maximum properties. The minimum physical properties required for the sheet include thickness, peak load,
elongation, tear strength, adhesion to plywood, side lap integrity, thermal stability, and granule loss.
SCOPE
1.1 This specification covers prefabricated, self-adhesive, glass fiber fabric reinforced, polymer-modified asphalt roll roofing, with granule surfacing, designed for steep slope applications. These products use polymer modifiers in their top and bottom coatings. These products have an adhesive bottom layer which is exposed by removal of a peel-away protective release paper or film sheet.  
1.2 The specified tests and property limits used to characterize the sheet materials are intended to establish minimum, or maximum properties. In-place roof system design criteria, such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others, are factors beyond the scope of this material specification. Factors regarding the suitability of specific roof constructions or application techniques are beyond this scope.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Jun-2017
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: D08 - Roofing and Waterproofing
• Drafting Committee: D08.02 - Steep Roofing Products and Assemblies

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7530/D7530M − 17
Standard Specification for
Self-Adhesive Glass Fiber Fabric Reinforced Polymer
Modified Asphalt Steep Slope Roll Roofing Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D7530/D7530M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This specification covers prefabricated, self-adhesive, 2.1 ASTM Standards:
glass fiber fabric reinforced, polymer-modified asphalt roll D903 Test Method for Peel or Stripping Strength of Adhe-
roofing, with granule surfacing, designed for steep slope sive Bonds
applications. These products use polymer modifiers in their top D1079 Terminology Relating to Roofing and Waterproofing
and bottom coatings. These products have an adhesive bottom D4977/D4977M Test Method for Granule Adhesion to Min-
layer which is exposed by removal of a peel-away protective eral Surfaced Roofing by Abrasion
release paper or film sheet. D5147/D5147M Test Methods for Sampling and Testing
Modified Bituminous Sheet Material
1.2 The specified tests and property limits used to charac-
terize the sheet materials are intended to establish minimum, or
3. Terminology
maximum properties. In-place roof system design criteria, such
3.1 Definitions:
as fire resistance, field strength, impact/puncture resistance,
3.1.1 For definitions of terms used in this specification, refer
material compatibility, uplift resistance, and others, are factors
to Terminology D1079.
beyond the scope of this material specification. Factors regard-
3.1.2 ultimate elongation, n—the elongation measured on
ing the suitability of specific roof constructions or application
the load-elongation curve at which point the load has dropped
techniques are beyond this scope.
to 5 % of its maximum value, after the peak load has been
1.3 The values stated in either SI units or inch-pound units
reached.
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
4. Materials and Manufacture
system shall be used independently of the other. Combining
4.1 In the process of manufacture, the reinforcing mat is
values from the two systems may result in non-conformance
impregnated and coated on its top and bottom sides with
with the standard.
polymer modified asphalt coatings. The polymer modified
1.4 This standard does not purport to address all of the
asphalt coatings are permitted to be compounded with a
safety concerns, if any, associated with its use. It is the
mineral stabilizer. The coating on the bottom side shall feature
responsibility of the user of this standard to establish appro-
self-adhesive properties.
priate safety and health practices and determine the applica-
4.2 The sheet is surfaced on the weather side with mineral
bility of regulatory limitations prior to use.
granules, except for any selvage.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
5. Physical Properties
ization established in the Decision on Principles for the
5.1 The sheet shall conform to the minimum physical
Development of International Standards, Guides and Recom-
properties prescribed in Table 1.
mendations issued by the World Trade Organization Technical
5.2 The finished product shall not crack nor be so sticky as
Barriers to Trade (TBT) Committee.
to cause tearing or other material damage upon being unrolled
at any product temperature between 4 and 60°C [40 and 140°F]
1
This specification is under the jurisdiction of ASTM Committee D08 on
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
2
on Steep Roofing Products and Assemblies. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved July 1, 2017. Published July 2017. Originally approved contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
in 2010. Last previous edition approved in 2010 as D7530/D7530M – 10. Standards volume information, refer to the standard’s Document Summary page on
DOI:10.1520/D7530_D7530M–17. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7530/D7530M − 17
TABLE 1 Physical Properties of Self-Adhesive Glass Fiber Fabric Reinforced Polymer Modified Asphalt Steep Slope Roll Roofing
A,B
Surfaced with Mineral Granules
Property SI [inch-pound]
Thickness, min, mm [mils] 3 [120]
Peak Load at –18 ± 2°C [0 ± 4°F], MD and XMD, m
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7530/D7530M − 10 D7530/D7530M − 17
Standard Specification for
Self-Adhesive Glass Fiber Fabric Reinforced Polymer
Modified Asphalt Steep Slope Roll Roofing Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D7530/D7530M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers prefabricated, self-adhesive, glass fiber fabric reinforced, polymer-modified asphalt roll roofing,
with granule surfacing, designed for steep slope applications. These products use polymer modifiers in their top and bottom
coatings. These products have an adhesive bottom layer which is exposed by removal of a peel-away protective release paper or
film sheet.
1.2 The specified tests and property limits used to characterize the sheet materials are intended to establish minimum, or
maximum properties. In-place roof system design criteria, such as fire resistance, field strength, impact/puncture resistance,
material compatibility, uplift resistance, and others, are factors beyond the scope of this material specification. Factors regarding
the suitability of specific roof constructions or application techniques are beyond this scope.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Steep
Roofing Products and Assemblies.
Current edition approved July 1, 2010July 1, 2017. Published July 2010July 2017. DOI:10.1520/D7530_D75305M–10. Originally approved in 2010. Last previous edition
approved in 2010 as D7530/D7530M – 10. DOI:10.1520/D7530_D7530M–17.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7530/D7530M − 17
2. Referenced Documents
2
2.1 ASTM Standards:
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
D1079 Terminology Relating to Roofing and Waterproofing
D4977D4977/D4977M Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
D5147D5147/D5147M Test Methods for Sampling and Testing Modified Bituminous Sheet Material
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms used in this specification, refer to Terminology D1079.
3.1.2 ultimate elongation, n—the elongation measured on the load-elongation curve at which point the load has dropped to 5 %
of its maximum value.value, after the peak load has been reached.
4. Materials and Manufacture
4.1 In the process of manufacture, the reinforcing mat is impregnated and coated on its top and bottom sides with polymer
modified asphalt coatings. The polymer modified asphalt coatings are permitted to be compounded with a mineral stabilizer. The
coating on the bottom side shall feature self-adhesive properties.
4.2 The sheet is surfaced on the weather side with mineral granules, except for any selvage.
5. Physical Properties
5.1 The sheet shall conform to the minimum physical properties prescribed in Table 1.
5.2 The finished product shall not crack nor be so sticky as to cause tearing or other material damage upon being unrolled at
any product temperature between 4 and 60°C [40 and 140°F] or at a lower temperature if the manufacturer allows application at
such lower temperature.
5.3 The release paper, or film sheet, shall not tear during removal.
6. Dimensions and Permissible Varia
...