ASTM E2266-11(2019)
(Guide)Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
SIGNIFICANCE AND USE
5.1 This guide may be used by public agencies to set standards affecting the weather resistance, durability, and performance of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints beyond those specifically defined in the building codes.
5.2 This guide may be used by building field inspectors as a resource for construction inspection during the construction phase of a project.
5.3 This guide may be used by private organizations or individuals to set standards affecting the weather resistance, durability, and performance of building walls.
5.4 This guide may be used by architects and engineers as a resource for making design decisions involving material selection, building wall detailing and specifications.
5.5 This guide may be used by architects and engineers as a resource for conducting submittal review and construction observation during the construction administration phase of a project.
5.6 This guide may be used by contractors as a resource and checklist for exercising field quality control.
SCOPE
1.1 This guide describes design, specification, selection, installation, and inspection of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints of wood and metal frame buildings, typically four stories or less, to minimize water intrusion.
1.2 This guide does not address prevention of damage caused by water originating from the use of wet building materials or from indoor or outdoor humidity. Water from these sources can be important, and the potential for damage caused by water from these sources must not be overlooked in building design or construction.
1.3 This guide does not address roofing systems, except when the surface of a deck also serves as a roof and at locations where roof systems interface with building walls.
1.4 This guide does not address any type of barrier wall system.
1.5 This guide does not address any exterior insulation and finish system (EIFS).
1.6 This guide does not address foundation conditions where the bottom of a slab on grade or the grade of a crawl space is at or below the water table or subject to hydrostatic pressure.
1.7 This guide is intended to supplement and not duplicate building code requirements.
1.8 Maintenance, although important, is not covered in detail.
1.9 Application of finishes, such as paint and sealers, may be important in the performance of some types of cladding; however, this is not covered in detail.
1.10 This guide applies only to constructions with sheathing, which facilitates installation of the weather-resistive barrier and associated flashings in a common plane.
1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.12 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.
1.13 Organization of Document:
Section
Scope
1
Referenced Documents
2
Terminology
3
Summary of Guide
4
Significance and Use
5
General Design Principles
6
Design Practices
7
General Guidelines
8
Drainage Walls
9
Drainage Walls—General
9.1
Drainage Wall Cladding—Portland Cement Plaster (Stucco)
9.2
Drainage Wall Cladding—Wood and Wood-Derived Products
9.3
Drainage Wall Cladding—Vinyl Siding
9.4
Drainage Wall Cladding—Fiber-Cement Siding
9.5
Cavity Drainage Walls
10
Cavity Drainage Walls—General
10.1
Cavity Drainage Wall Cladding—Mason...
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E2266 − 11 (Reapproved 2019)
Standard Guide for
Design and Construction of Low-Rise Frame Building Wall
Systems to Resist Water Intrusion
This standard is issued under the fixed designation E2266; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.11 The values stated in SI units are to be regarded as
standard. The values given in parentheses after SI units are
1.1 This guide describes design, specification, selection,
provided for information only and are not considered standard.
installation, and inspection of new building wall systems,
exterior deck and stair components, doors, windows, penetra-
1.12 This standard may involve hazardous materials,
tions and sealant joints of wood and metal frame buildings,
operations, and equipment. This standard does not purport to
typically four stories or less, to minimize water intrusion.
address all of the safety concerns, if any, associated with its
1.2 This guide does not address prevention of damage
use. It is the responsibility of the user of this standard to
caused by water originating from the use of wet building
establish appropriate safety, health, and environmental prac-
materialsorfromindoororoutdoorhumidity.Waterfromthese
tices and determine the applicability of regulatory require-
sources can be important, and the potential for damage caused
ments prior to use.
bywaterfromthesesourcesmustnotbeoverlookedinbuilding
1.13 Organization of Document:
design or construction.
Section
1.3 This guide does not address roofing systems, except Scope 1
Referenced Documents 2
whenthesurfaceofadeckalsoservesasaroofandatlocations
Terminology 3
where roof systems interface with building walls.
Summary of Guide 4
Significance and Use 5
1.4 This guide does not address any type of barrier wall
General Design Principles 6
system.
Design Practices 7
General Guidelines 8
1.5 This guide does not address any exterior insulation and
Drainage Walls 9
finish system (EIFS).
Drainage Walls—General 9.1
Drainage Wall Cladding—Portland Cement Plaster 9.2
1.6 This guide does not address foundation conditions
(Stucco)
Drainage Wall Cladding—Wood and Wood-Derived 9.3
where the bottom of a slab on grade or the grade of a crawl
Products
space is at or below the water table or subject to hydrostatic
Drainage Wall Cladding—Vinyl Siding 9.4
pressure.
Drainage Wall Cladding—Fiber-Cement Siding 9.5
Cavity Drainage Walls 10
1.7 This guide is intended to supplement and not duplicate
Cavity Drainage Walls—General 10.1
building code requirements.
Cavity Drainage Wall Cladding—Masonry 10.2
Wood Framed Decks and Stairs with Exposed Framing 11
1.8 Maintenance, although important, is not covered in
and Decking
Plaza Decks or Stairs with Enclosed Framing and a 12
detail.
Waterproofing Membrane with Separate Wearing
1.9 Application of finishes, such as paint and sealers, may
Surfaces
Plaza Decks or Stairs with Enclosed Framing and a 13
be important in the performance of some types of cladding;
Waterproofing Membrane with an Integral Wearing
however, this is not covered in detail.
Surface
Windows, Doors, and Similar Wall Penetrations 14
1.10 This guide applies only to constructions with
Special Wall Configuration 15
sheathing, which facilitates installation of the weather-resistive
Exterior Sealant Joints 16
barrier and associated flashings in a common plane. Keywords 17
Appendix—Additional Resources Appendix
X1
This guide is under the jurisdiction of ASTM Committee E06 on Performance
Appendix—General Notes for Cement Plaster (Stucco) Appendix
of Buildings and is the direct responsibility of Subcommittee E06.55 on Perfor-
Details X2
mance of Building Enclosures.
Current edition approved Aug. 15, 2019. Published August 2019. Originally
approved in 2004. Last previous edition approved in 2011 as E2266–11. DOI:
10.1520/E2266–11R19.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
E2266 − 11 (2019)
1.14 This international standard was developed in accor- C1127/C1127M Guide for Use of High Solids Content, Cold
dance with internationally recognized principles on standard- Liquid-Applied Elastomeric Waterproofing Membrane
ization established in the Decision on Principles for the
with an Integral Wearing Surface
Development of International Standards, Guides and Recom- C1180 Terminology of Mortar and Grout for Unit Masonry
mendations issued by the World Trade Organization Technical
C1186 Specification for Flat Fiber-Cement Sheets
Barriers to Trade (TBT) Committee.
C1193 Guide for Use of Joint Sealants
C1209 Terminology of Concrete Masonry Units and Related
2. Referenced Documents
Units (Withdrawn 2009)
2.1 ASTM Standards:
C1232 Terminology for Masonry
A153/A153M Specification for Zinc Coating (Hot-Dip) on
C1299 Guide for Use in Selection of Liquid-Applied Seal-
Iron and Steel Hardware
ants (Withdrawn 2012)
C11 Terminology Relating to Gypsum and Related Building
C1400 Guide for Reduction of Efflorescence Potential in
Materials and Systems
New Masonry Walls
C43 Terminology of Structural Clay Products (Withdrawn
C1405 Specification for Glazed Brick (Single Fired, Brick
2009)
Units)
C55 Specification for Concrete Building Brick
D226/D226M Specification for Asphalt-Saturated Organic
C62 Specification for Building Brick (Solid Masonry Units
Felt Used in Roofing and Waterproofing
Made From Clay or Shale)
D1079 Terminology Relating to Roofing and Waterproofing
C67/C67M Test Methods for Sampling and Testing Brick
D1970/D1970M Specification for Self-Adhering Polymer
and Structural Clay Tile
Modified Bituminous Sheet Materials Used as Steep
C90 Specification for Loadbearing Concrete Masonry Units
Roofing Underlayment for Ice Dam Protection
C126 Specification for Ceramic Glazed Structural Clay Fac-
D3679 Specification for Rigid Poly(Vinyl Chloride) (PVC)
ing Tile, Facing Brick, and Solid Masonry Units
Siding
C150 Specification for Portland Cement
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl
C168 Terminology Relating to Thermal Insulation
Chloride) (PVC) Soffit
C216 Specification for Facing Brick (Solid Masonry Units
D4756 Practice for Installation of Rigid Poly(Vinyl Chlo-
Made from Clay or Shale)
ride) (PVC) Siding and Soffit
C270 Specification for Mortar for Unit Masonry
D5843/D5843M Guide for Application of Fully Adhered
C652 Specification for Hollow Brick (Hollow Masonry
Vulcanized Rubber Sheets Used in Waterproofing
Units Made From Clay or Shale)
D5898 Guide for Standard Details forAdhered Sheet Water-
C717 Terminology of Building Seals and Sealants
proofing
C755 Practice for Selection of Water Vapor Retarders for
D5957 Guide for Flood Testing Horizontal Waterproofing
Thermal Insulation
Installations
C836/C836M Specification for High Solids Content, Cold
D6134 Specification for Vulcanized Rubber Sheets Used in
Liquid-Applied Elastomeric Waterproofing Membrane for
Waterproofing Systems
Use with Separate Wearing Course
D6135 Practice for Application of Self-Adhering Modified
C896 Terminology Relating to Clay Products
Bituminous Waterproofing (Withdrawn 2014)
C898/C898M Guide for Use of High Solids Content, Cold
D6622/D6622M Guide for Application of Fully Adhered
Liquid-Applied Elastomeric Waterproofing Membrane
Hot-Applied Reinforced Waterproofing Systems
with Separate Wearing Course
D6864 Specification for Color andAppearance Retention of
C920 Specification for Elastomeric Joint Sealants
Solid Colored Plastic Siding Products (Withdrawn 2018)
C926 Specification for Application of Portland Cement-
E241 Guide for Limiting Water-Induced Damage to Build-
Based Plaster
ings
C957/C957M Specification for High-Solids Content, Cold
E331 Test Method for Water Penetration of Exterior
Liquid-Applied Elastomeric Waterproofing Membrane
Windows, Skylights, Doors, and Curtain Walls by Uni-
With Integral Wearing Surface
form Static Air Pressure Difference
C981 Guide for Design of Built-Up Bituminous Membrane
E547 Test Method for Water Penetration of Exterior
Waterproofing Systems for Building Decks
Windows, Skylights, Doors, and Curtain Walls by Cyclic
C1063 Specification for Installation of Lathing and Furring
Static Air Pressure Difference
to Receive Interior and Exterior Portland Cement-Based
E631 Terminology of Building Constructions
Plaster
E1105 Test Method for Field Determination of Water Pen-
C1088 Specification for Thin Veneer Brick Units Made
etration of Installed Exterior Windows, Skylights, Doors,
From Clay or Shale
and Curtain Walls, by Uniform or Cyclic Static Air
Pressure Difference
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E1677 SpecificationforAirBarrier(AB)MaterialorAssem-
Standards volume information, refer to the standard’s Document Summary page on
blies for Low-Rise Framed Building Walls
the ASTM website.
E1825 Guide for Evaluation of Exterior Building Wall
The last approved version of this historical standard is referenced on
www.astm.org. Materials, Products, and Systems
E2266 − 11 (2019)
E2112 Practice for Installation of Exterior Windows, Doors 2.9 CGSB Standard:
and Skylights CAN/CGSB 51.32-M77 Sheathing, Membrane, Breather
F1667 Specification for Driven Fasteners: Nails, Spikes, and Type
Staples
2.10 CMHC Standard:
2.2 AAMA Standards:
Wood-Frame Envelopes in the Coastal Climate of British
AAMA 501 Methods of Test for Metal Curtain Walls
Columbia
AAMA501.2 Field Check of Metal Curtain Walls for Water
2.11 CPA Standards:
Leakage
ANSI/AHA 135.6 Hardboard Siding
AAMA 502 Voluntary Specification for Field Testing of
RecommendedBasicApplicationInstructionsforHardboard
Windows and Sliding Doors
Siding
AAMA 850 Fenestration Sealants Guide Manual
Coatings Specification for Field-Applied Coatings on Hard-
AAMA IM-TM InstallationMasters Training Manual Win-
board Siding
dow Selection Guide
Finishing Recommendations for New Construction Using
2.3 ACI Standards:
Unprimed and Primed Hardboard Siding
ACI 524 Guide to Portland Cement Plastering
Maintenance Tips for Hardboard Siding
2.4 ANSI Standards:
2.12 CSSB Standards:
ANSI/ASCE 7 Building Code Requirements for Minimum
Wall Construction Manual
Design Loads in Buildings and Other Structures
Grading Rules for Certigrade Red Cedar Shingles
ANSI/AHA A135.6 American National Standard for Hard-
Grading Rules for Certi-Split Red Cedar Shakes
board Siding
Grading Rules for Tapersawn Red Cedar Shakes
ANSI/AAMA/NWWDA 101/I.S. 2-97 Voluntary Specifica-
2.13 Federal Specification:
tionsforAluminum,Vinyl(PVC)andWoodWindowsand
UU B 790a Building Paper
Glass Doors
ANSI/AAMA/WDMA 101/I.S. 2/NAFS-02 Voluntary Per-
2.14 ICC-ES Standards:
formanceSpecificationforWindows,Skylights,andGlass AC38 Acceptance Criteria for Weather-Resistive Barriers
Doors
AC39 Acceptance Criteria for Walking Decks
2.5 APA Standards:
2.15 MLPB Standard:
APA 303 Siding Manufacturing Specifications
Stucco in Residential Construction
Avoiding Moisture Accumulation in Walls
2.16 NCMA Standard:
Buckling of Wood-Based Panel Siding
NCMA TEK Bulletins
Installation of Stucco Exterior Finish Over Wood Structural
2.17 NELMA Standard:
Panel Wall Sheathing
Standard Grading Rules for Northeastern Lumber
Product Guide Performance Rated Sidings
2.18 NRCA Standard:
2.6 AWPA Standards:
NRCA Roofing and Waterproofing Manual
AWPA C2 Lumber, Timbers, Bridge Ties and Mine Ties,
Pressure Treatment
2.19 NWCB Standard:
AWPAC28 PreservativeTreatment by Pressure Processes of
Stucco Resource Guide
Structural Glue Laminated Members and Laminations
Before Gluing
AWPA M4 Care of Pressure Treated Wood Products
Available from Canadian General Standards Board (CGSB), 11 Laurier St.,
Phase III, Place du Portage, Gatineau, Quebec K1A0S5, Canada, http://www.tpsgc-
2.7 BIA Standard:
pwgsc.gc.ca/ongc-cgsb.
Technical Notes on Brick Construction
Available from Canadian Mortgage and Housing Corporation (CMHC), 700
2.8 CCMC Standard:
Montreal Road, Ottawa, Ontario, K1A 0P7, Canada, http://www.cmhc-schl.gc.ca.
Available from Composite PanelAssociation (CPA), 19465 DeerfieldAvenue,
NRCC-45-673 Technical Guide for Sheathing, Membrane,
Suite 306, Leesburg, VA 20176, https://www.compositepanel.org/.
Breather-Type
Available from Cedar Shake and Shingle Bureau (CSSB), 7101 Horne St #2,
Mission, BC V2V 7A2, Canada, http://www.cedarbureau.org.
4 15
Available from American Architectural Manufacturers Association (AAMA), Available from U.S. General Services Administration (GSA), 1800 F Street,
1827 Walden Office Square, Suite 550, Schaumburg, IL 60173-4268, http:// NW Washington, DC 20405, http://www.gsa.gov.
www.aamanet.org. The ICC Evaluation Service (ICC-ES) is reviewing Acceptance Criteria
Available from American Concrete Institute (ACI), 38800 Country Club Dr., previously issued by the ICBO Evaluation Service. At the publication of this
Farmington Hills, MI 48331-3439, http://www.concrete.org. standard,AC38 andAC39 are considered Interim Criteria. ICC Evaluation Service,
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St., 3060 Saturn Street, Suite 100, Brea, California 92821, http://www.icc-es.org.
4th Floor, New York, NY 10036, http://www.ansi.org. Available from Minnesota Lath and Plaster Bureau (MLPB), 1270 Northland
Available fromAPA– The Engineered WoodAssociation, 7011 S. 19th Street, Dr, Ste 150, Mendota Hts, MN 55120, http://www.mnlath-plaster.com.
Tacoma, WA 98466-5333, http://www.apawood.org. Available from National Concrete Masonry Association (NCMA), 13750
Available from American Wood Protection Association (AWPA), P.O. Box Sunrise Valley Drive, Herndon, VA 20171, http://www.ncma.org.
361784, Birmingham, AL 35236-1784, http://www.awpa.com. Available from Northeastern Lumber Manufacturers Association (NELMA),
Available from The Brick Industry Association (BIA), 12007 Sunrise Valley 272 Tuttle Road, Cumberland Center, ME 04021, http://www.nelma.org.
Drive, Suite 430, Reston, VA 20191, http://www.gobrick.com. Available from National Roofing ContractorsAssociation (NRCA), 10255 W.
Available from Canadian Construction Materials Centre (CCMC), Institute for Higgins Road, Suite 600, Rosemont, IL 600185607, http://www.nrca.net.
Research in Construction, National Research Council Canada, 1200 Montreal Road, Available from Northwest Wall & Ceiling Bureau (NWCB), 2825 Eastlake
Building M58, Ottawa, Ontario K1A 0R6, https://nrc-cnrc.canada.ca/. Ave E, Ste 350, Seattle, WA 98
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2266 − 11 E2266 − 11 (Reapproved 2019)
Standard Guide for
Design and Construction of Low-Rise Frame Building Wall
Systems to Resist Water Intrusion
This standard is issued under the fixed designation E2266; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide describes design, specification, selection, installation, and inspection of new building wall systems, exterior deck
and stair components, doors, windows, penetrations and sealant joints of wood and metal frame buildings, typically four stories
or less, to minimize water intrusion.
1.2 This guide does not address prevention of damage caused by water originating from the use of wet building materials or
from indoor or outdoor humidity. Water from these sources can be important, and the potential for damage caused by water from
these sources must not be overlooked in building design or construction.
1.3 This guide does not address roofing systems, except when the surface of a deck also serves as a roof and at locations where
roof systems interface with building walls.
1.4 This guide does not address any type of barrier wall system.
1.5 This guide does not address any exterior insulation and finish system (EIFS).
1.6 This guide does not address foundation conditions where the bottom of a slab on grade or the grade of a crawl space is at
or below the water table or subject to hydrostatic pressure.
1.7 This guide is intended to supplement and not duplicate building code requirements.
1.8 Maintenance, although important, is not covered in detail.
1.9 Application of finishes, such as paint and sealers, may be important in the performance of some types of cladding; however,
this is not covered in detail.
1.10 This guide applies only to constructions with sheathing, which facilitates installation of the weather-resistive barrier and
associated flashings in a common plane.
1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions
to inch-pound units that after SI units are provided for information only and are not considered standard.
1.12 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all
of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate
safety safety, health, and healthenvironmental practices and determine the applicability of regulatory requirements prior to use.
1.13 Organization of Document:
Section
Scope 1
Referenced Documents 2
Terminology 3
Summary of Guide 4
Significance and Use 5
General Design Principles 6
Design Practices 7
General Guidelines 8
Drainage Walls 9
Drainage Walls—General 9.1
Drainage Wall Cladding—Portland Cement Plaster 9.2
This guide is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.55 on Performance of
Building Enclosures.
Current edition approved Feb. 1, 2011Aug. 15, 2019. Published June 2011August 2019. Originally approved in 2004. Last previous versionedition approved in 20042011
as E2266– 04.DOI: 10.1520/E2266-11.–11. DOI: 10.1520/E2266–11R19.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
E2266 − 11 (2019)
Section
(Stucco)
Drainage Wall Cladding—Wood and Wood-Derived 9.3
Products
Drainage Wall Cladding—Vinyl Siding 9.4
Drainage Wall Cladding—Fiber-Cement Siding 9.5
Cavity Drainage Walls 10
Cavity Drainage Walls—General 10.1
Cavity Drainage Wall Cladding—Masonry 10.2
Wood Framed Decks and Stairs with Exposed Framing 11
and Decking
Plaza Decks or Stairs with Enclosed Framing and a 12
Waterproofing Membrane with Separate Wearing
Surfaces
Plaza Decks or Stairs with Enclosed Framing and a 13
Waterproofing Membrane with an Integral Wearing
Surface
Windows, Doors, and Similar Wall Penetrations 14
Special Wall Configuration 15
Exterior Sealant Joints 16
Keywords 17
Appendix—Additional Resources Appendix
X1
Appendix—General Notes for Cement Plaster (Stucco) Appendix
Details X2
E2266 − 11 (2019)
1.14 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C43 Terminology of Structural Clay Products (Withdrawn 2009)
C55 Specification for Concrete Building Brick
C62 Specification for Building Brick (Solid Masonry Units Made From Clay or Shale)
C67C67/C67M Test Methods for Sampling and Testing Brick and Structural Clay Tile
C90 Specification for Loadbearing Concrete Masonry Units
C126 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C150 Specification for Portland Cement
C168 Terminology Relating to Thermal Insulation
C216 Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C270 Specification for Mortar for Unit Masonry
C652 Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)
C717 Terminology of Building Seals and Sealants
C755 Practice for Selection of Water Vapor Retarders for Thermal Insulation
C836C836/C836M Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use
with Separate Wearing Course
C896 Terminology Relating to Clay Products
C898C898/C898M Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with
Separate Wearing Course
C920 Specification for Elastomeric Joint Sealants
C926 Specification for Application of Portland Cement-Based Plaster
C957C957/C957M Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With
Integral Wearing Surface
C981 Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks
C1063 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
C1088 Specification for Thin Veneer Brick Units Made From Clay or Shale
C1127C1127/C1127M Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with
an Integral Wearing Surface
C1180 Terminology of Mortar and Grout for Unit Masonry
C1186 Specification for Flat Fiber-Cement Sheets
C1193 Guide for Use of Joint Sealants
C1209 Terminology of Concrete Masonry Units and Related Units (Withdrawn 2009)
C1232 Terminology for Masonry
C1299 Guide for Use in Selection of Liquid-Applied Sealants (Withdrawn 2012)
C1400 Guide for Reduction of Efflorescence Potential in New Masonry Walls
C1405 Specification for Glazed Brick (Single Fired, Brick Units)
D226D226/D226M Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
D1079 Terminology Relating to Roofing and Waterproofing
D1970D1970/D1970M Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing
Underlayment for Ice Dam Protection
D3679 Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
D4756 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
D5843D5843/D5843M Guide for Application of Fully Adhered Vulcanized Rubber Sheets Used in Waterproofing
D5898 Guide for Standard Details for Adhered Sheet Waterproofing
D5957 Guide for Flood Testing Horizontal Waterproofing Installations
D6134 Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
The last approved version of this historical standard is referenced on www.astm.org.
E2266 − 11 (2019)
D6135 Practice for Application of Self-Adhering Modified Bituminous Waterproofing (Withdrawn 2014)
D6622D6622/D6622M Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
D6864 Specification for Color and Appearance Retention of Solid Colored Plastic Siding Products (Withdrawn 2018)
E241 Guide for Limiting Water-Induced Damage to Buildings
E331 Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air
Pressure Difference
E547 Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure
Difference
E631 Terminology of Building Constructions
E1105 Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain
Walls, by Uniform or Cyclic Static Air Pressure Difference
E1677 Specification for Air Barrier (AB) Material or Assemblies for Low-Rise Framed Building Walls
E1825 Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems
E2112 Practice for Installation of Exterior Windows, Doors and Skylights
F1667 Specification for Driven Fasteners: Nails, Spikes, and Staples
2.2 AAMA Standards:
AAMA 501 Methods of Test for Metal Curtain Walls
AAMA 501.2 Field Check of Metal Curtain Walls for Water Leakage
AAMA 502 Voluntary Specification for Field Testing of Windows and Sliding Doors
AAMA 850 Fenestration Sealants Guide Manual
AAMA IM-TM InstallationMasters Training Manual Window Selection Guide
2.3 ACI Standards:
ACI 524 Guide to Portland Cement Plastering
2.4 ANSI Standards:
ANSI/ASCE 7 Building Code Requirements for Minimum Design Loads in Buildings and Other Structures
ANSI/AHA A135.6 American National Standard for Hardboard Siding
ANSI/AAMA/NWWDA 101/I.S. 2-97 Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass
Doors
ANSI/AAMA/WDMA 101/I.S. 2/NAFS-02 Voluntary Performance Specification for Windows, Skylights, and Glass Doors
2.5 APA Standards:
APA 303 Siding Manufacturing Specifications
Avoiding Moisture Accumulation in Walls
Buckling of Wood-Based Panel Siding
Installation of Stucco Exterior Finish Over Wood Structural Panel Wall Sheathing
Product Guide Performance Rated Sidings
2.6 AWPA Standards:
AWPA C2 Lumber, Timbers, Bridge Ties and Mine Ties, Pressure Treatment
AWPA C28 Preservative Treatment by Pressure Processes of Structural Glue Laminated Members and Laminations Before
Gluing
AWPA M4 Care of Pressure Treated Wood Products
2.7 BIA Standards:Standard:
Technical Notes on Brick Construction
2.8 CCMC Standards:Standard:
NRCC-45-673 Technical Guide for Sheathing, Membrane, Breather-Type
2.9 CGSB Standards:Standard:
CAN/CGSB 51.32-M77 Sheathing, Membrane, Breather Type
2.10 CMHC Standards:Standard:
Wood-Frame Envelopes in the Coastal Climate of British Columbia
Available from American Architectural Manufacturers Association (AAMA), 1827 Walden Office Square, Suite 550, Schaumburg, IL 60173-4628,60173-4268,
http://www.aamanet.org.
Available from American Concrete Institute (ACI), P.O. Box 9094, 38800 Country Club Dr., Farmington Hills, MI 48333-9094,48331-3439, http://www.concrete.org.
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Available from APA – The Engineered Wood Association, 7011 S. 19th Street, Tacoma, WA 98466-5333, http://www.apawood.org.
Available from American Wood Protection Association (AWPA), P.O. Box 361784, Birmingham, AL 35236-1784, http://www.awpa.com.
Available from The Brick Industry Association (BIA), 1850 Centennial Park12007 Sunrise Valley Drive, Suite 301,430, Reston, VA 20191, http://www.gobrick.com.
Available from Canadian Construction Materials Centre (CCMC), Institute for Research in Construction, National Research Council Canada, 1200 Montreal Road,
Building M-24,M58, Ottawa, Ontario K1A R6, http://www.nrc-cnrc.gc.ca. 0R6, https://nrc-cnrc.canada.ca/.
Available from Canadian General Standards Board (CGSB), Gatineau, Canada K1A1G6.11 Laurier St., Phase III, Place du Portage, Gatineau, Quebec K1A 0S5, Canada,
http://www.tpsgc-pwgsc.gc.ca/ongc-cgsb.
Available from Canadian Mortgage and Housing Corporation (CMHC), 700 Montreal Road, Ottawa, Ontario, K1A 0P7, Canada, http://www.cmhc-schl.gc.ca.
E2266 − 11 (2019)
2.11 CPA Standards:
ANSI/AHA 135.6 Hardboard Siding
Recommended Basic Application Instructions for Hardboard Siding
Coatings Specification for Field-Applied Coatings on Hardboard Siding
Finishing Recommendations for New Construction Using Unprimed and Primed Hardboard Siding
Maintenance Tips for Hardboard Siding
2.12 CSSB Standards:
Wall Construction Manual
Grading Rules for Certigrade Red Cedar Shingles
Grading Rules for Certi-Split Red Cedar Shakes
Grading Rules for Tapersawn Red Cedar Shakes
2.13 Federal Specification:
UU B 790a Building Paper
2.14 ICC-ES Standards:
AC38 Acceptance Criteria for Weather-Resistive Barriers
AC39 Acceptance Criteria for Walking Decks
2.15 MLPB Standards:Standard:
Stucco in Residential Construction
2.16 NCMA Standards:Standard:
NCMA TEK Bulletins
2.17 NELMA Standards:Standard:
Standard Grading Rules for Northeastern Lumber
2.18 NRCA Standards:Standard:
NRCA Roofing and Waterproofing Manual
2.19 NWCB Standards:Standard:
Stucco Resource Guide
2.20 PCA Standards:Standard:
Portland Cement (Stucco) Manual
2.21 RIS Standards:Standard:
Standard Specifications for Grades of California Redwood Lumber
2.22 SMACNA Standards:
Architectural Sheet Metal Manual
Residential Sheet Metal Guidelines
2.23 SPC Standards:Standard:
Guide to Southern Pine Siding
2.24 SPIB Standards:Standard:
Standard Grading Rules for Southern Pine Lumber
2.25 SPRI Standards:Standard:
Flexible Membrane Roofing: A Professional’sProfessional’s Guide to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.