ASTM F1193-05

Standard Practice for Amusement Ride and Device Manufacturer Quality Assurance Program and Manufacturing Requirements

SCOPE
1.1 This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications).
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Nov-2005
• ICS: 97.200.99 - Other equipment for entertainment
• Technical Committee: F24 - Amusement Rides and Devices
• Drafting Committee: F24.24 - Design, Manufacture, Installation and commissioning

Relations

• Replaces: ASTM F1193-04b - Standard Practice for Amusement Ride and Device Manufacturer Quality Assurance Program and Manufacturing Requirements
• Effective Date: 01-Dec-2005
• Replaced By: ASTM F1193-06 - Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices
• Effective Date: 01-Mar-2006
• Referred By: ASTM F2007-18 - Standard Practice for Design, Manufacture, and Operation of Concession Go-Karts and Facilities
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2375-09(2017) - Standard Practice for Design, Manufacture, Installation and Testing of Climbing Nets and Netting/Mesh used in Amusement Rides, Devices, Play Areas and Attractions
• Effective Date: 01-Dec-2005
• Referred By: ASTM F770-23 - Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices
• Effective Date: 01-Dec-2005
• Referred By: ASTM F3158-22 - Standard Practice for Patron Transportation Conveyors Used with a Water Related Amusement Ride or Device
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2460-19 - Standard Practice for Special Requirements for Bumper Boats
• Effective Date: 01-Dec-2005
• Referred By: ASTM F1159-16e1 - Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2959-23a - Standard Practice for Aerial Adventure Courses
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2461-23 - Standard Practice for Manufacture, Construction, Operation, and Maintenance of Aquatic Play Equipment
• Effective Date: 01-Dec-2005
• Referred By: ASTM F3168-23 - Standard Practice for Hayride Attractions
• Effective Date: 01-Dec-2005
• Referred By: ASTM F3133-21 - Standard Practice for Classification, Design, Manufacture, Construction, Maintenance, and Operation of Stationary Wave Systems
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2960-23 - Standard Practice for Permanent Amusement Railway Ride Tracks and Related Devices
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2376-23 - Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems
• Effective Date: 01-Dec-2005
• Referred By: ASTM F2970-22 - Standard Practice for Design, Manufacture, Installation, Operation, Maintenance, Inspection and Major Modification of Trampoline Courts
• Effective Date: 01-Dec-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 1193 – 05
Standard Practice for
Amusement Ride and Device Manufacturer Quality
1
Assurance Program and Manufacturing Requirements
This standard is issued under the fixed designation F 1193; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
3
1. Scope 2.2 AWS Standards:
As applicable.
1.1 This practice establishes the minimum requirements for
4
2.3 ASME Standards:
a quality assurance program and the manufacturing of amuse-
As applicable.
ment rides and devices (including major modifications).
1.2 This standard does not purport to address all of the
3. Significance and Use
safety concerns, if any, associated with its use. It is the
3.1 The purpose of this practice is to provide the minimum
responsibility of the user of this standard to establish appro-
manufacturing requirements for amusement rides and devices
priate safety and health practices and determine the applica-
and to provide the minimum requirements for a written quality
bility of regulatory limitations prior to use.
assurance program for an amusement ride or device manufac-
2. Referenced Documents turer, or component supplier. This is not intended to include
2
suppliers of off-the-shelf components (for example, fasteners,
2.1 ASTM Standards:
electrical wire, etc.).
E 543 Practice for Agencies Performing Nondestructive
Testing
4. Drawing Control Procedure
F 770 Practice for Operation Procedures for Amusement
4.1 A procedure shall be in effect so that appropriate
Rides and Devices
manufacturing drawings, their engineering revisions, and re-
F 846 Guide for Testing Performance of Amusement Rides
lated documents are utilized.
and Devices
F 853 Practice for Maintenance Procedures forAmusement
5. Material and Component Control Procedure
Rides and Devices
5.1 A procedure shall be in effect so that materials, pro-
F 893 Guide for Inspection of Amusement Rides and De-
cesses, and components, including raw materials, are in accor-
vices
dance with the engineering specifications.
F 1159 Practice for Design and Manufacture of Patron
5.1.1 This procedure shall provide the purchasing agent
Directed,Artificial Climbing Walls, Dry Slide, Coin Oper-
with all the information required to order appropriate material.
ated and Purposeful Water Immersion Amusement Rides
5.1.2 A receiving procedure shall be in effect so that
and Devices and Air-Supported Structures
incoming material and components are checked against the
F 1193 Practice forAmusement Ride and Device Manufac-
purchasing specifications.
turer Quality Assurance Program and Manufacturing Re-
5.1.3 Aprocedure shall be in effect so that material in stock
quirements
can be properly identified for future use.
F 1950 Specification for Physical Information to be Trans-
5.1.4 Documentation on any material, process, or compo-
ferred With Used Amusement Rides and Devices
nents certified shall be filed for reference.
F 2291 Practice for Design of Amusement Rides and De-
vices
6. Manufacturing
6.1 Amusement ride and device components and systems
1
This practice is under the jurisdiction ofASTM Committee F24 onAmusement
shall be manufactured and assembled in accordance with the
Rides and Devices and is the direct responsibility of Subcommittee F24.24 on
designer/engineer specified criteria.
Design and Manufacture.
Current edition approved Dec. 1, 2005. Published December 2005. Originally
approved in 1988. Last previous edition approved in 2004 as F 1193 – 04b.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from The American Welding Society (AWS), 550 NW LeJeune Rd.,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Miami, FL 33126.
4
Standards volume information, refer to the standard’s Document Summary page on Available from American Society of Mechanical Engineers (ASME), ASME
the ASTM website. International Headquarters, Three Park Ave., New York, NY 10016-5990.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1193–05
6.2 Changes to the designer/engineer specified criteria shall authority, purchaser, or owner, the manufacturer shall provide
be documented and approved by the designer/engineer or a a copy of this certification document.
qualified engineer before components, subassemblies, or sys-
10. Information Requirements
tems are placed into use.
10.1 The information given in 10.2 and 10.3–10.15.3 shall
6.3 Quality Assurance Program:
be included, where applicable, on the information plate as
6.3.1 The manufacturer of
...