ASTM B69-11
(Specification)Standard Specification for Rolled Zinc
Standard Specification for Rolled Zinc
ABSTRACT
This specification covers two types of commercial rolled zinc. Type I are coils or sheets cut from strip rolled zinc, and Type II are zinc plates such as boiler and hull plates produced by any rolling method. The products shall be produced by casting, rolling, and other processes found in mill product plant. The material shall be tested and conform to the required chemical composition. The testing of wrought zinc for determination of tensile properties shall be conducted. The testing of zinc for hardness shall be made on a Rockwell superficial hardness tester or on a microhardness tester. The determination of chemical composition shall be performed by either an appropriate chemical method or by optical emission spectrographic methods.
SCOPE
1.1 This specification covers two types of commercial rolled zinc as described in 1.2. It should be understood that the specification is general. Any closer limitations on permissible variations shall be a matter of agreement between the supplier (manufacturer) and the purchaser.
1.2 Rolled zinc is furnished in two types as follows:
1.2.1 Type I—Coils or sheets cut from strip (ribbon) rolled zinc and
1.2.2 Type II—Zinc plates such as boiler and hull plates produced by any rolling method.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B69 −11
StandardSpecification for
1
Rolled Zinc
This standard is issued under the fixed designation B69; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Ma-
1.1 Thisspecificationcoverstwotypesofcommercialrolled
terials
zinc as described in 1.2. It should be understood that the
E29 Practice for Using Significant Digits in Test Data to
specification is general. Any closer limitations on permissible
Determine Conformance with Specifications
variations shall be a matter of agreement between the supplier
E55 Practice for Sampling Wrought Nonferrous Metals and
(manufacturer) and the purchaser.
Alloys for Determination of Chemical Composition
1.2 Rolled zinc is furnished in two types as follows:
E60 Practice for Analysis of Metals, Ores, and Related
1.2.1 Type I—Coils or sheets cut from strip (ribbon) rolled
Materials by Spectrophotometry
zinc and
E88 Practice for Sampling Nonferrous Metals andAlloys in
1.2.2 Type II—Coils or sheets cut from strip (ribbon) rolled
Cast Form for Determination of Chemical Composition
zinc.
E384 Test Method for Knoop and Vickers Hardness of
1.3 The values stated in inch-pound units are to be regarded Materials
E527 Practice for Numbering Metals and Alloys in the
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only Unified Numbering System (UNS)
E536 Test Methods for ChemicalAnalysis of Zinc and Zinc
and are not considered standard.
Alloys
1.4 This standard does not purport to address all of the
E634 Practice for Sampling of Zinc and Zinc Alloys by
safety concerns, if any, associated with its use. It is the
Spark Atomic Emission Spectrometry
responsibility of the user of this standard to become familiar
3
2.3 ISO Standards:
with all hazards including those identified in the appropriate
ISO 3815-1 Zinc and zinc alloys—Part 1: Analysis of solid
Material Safety Data Sheet (MSDS) for this product/material
samples by optical emission spectrometry
as provided by the manufacturer, to establish appropriate
ISO 3815-2 Zinc and zinc alloys—Part 2: Analysis by in-
safety and health practices, and determine the applicability of
ductively coupled plasma optical emission spectrometry
regulatory limitations prior to use.
3. Terminology
2. Referenced Documents
3.1 Terms shall be defined in accordance with Terminology
2.1 The issue of each of the following reference documents
B899.
shall be that which is current on the date the purchase order is
3.2 Definitions of Terms Specific to This Standard:
accepted by the supplier (manufacturer).
3.2.1 architectural rolled zinc, Type 1, n—a lower copper
2
2.2 ASTM Standards:
composition architectural zinc that exhibits different properties
B899 Terminology Relating to Non-ferrous Metals and Al-
than Type 2.
loys
3.2.2 architectural rolled zinc, Type 2, n—a higher copper
composition architectural zinc that exhibits different properties
than Type 1.
1
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
3.2.3 coiled sheet, n—sheet coils with either slit or unslit
B02.04 on Zinc and Cadmium.
edges.
Current edition approved July 1, 2011. Published July 2011. Originally approved
in 1926. Last previous edition approved in 2010 as B69 - 10. DOI: 10.1520/B0069- 3.2.4 flat sheet, n—sheet with sheared, slit, or sawed edges
11.
that has been flattened or leveled.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B69−11
3.2.5 plate, n—rolled product, rectangular in cross section 8. Dimensions and Permissible Variations
and form, or thickness of more than 0.125 in. (3.175 mm) with
8.1 Thickness—The permissible variations in thickness of
either untrimmed, sheared or sawed edges.
rolled zinc shall be as specified in Table 3, along the length of
3.2.6 ribbo
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B69–10 Designation: B69 – 11
Standard Specification for
1
Rolled Zinc
This standard is issued under the fixed designation B69; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers two types of commercial rolled zinc as described in 1.2. It should be understood that the
specification is general. Any closer limitations on permissible variations shall be a matter of agreement between the supplier
(manufacturer) and the purchaser.
1.2 Rolled zinc is furnished in two types as follows:
1.2.1 Type I—Coils or sheets cut from strip (ribbon) rolled zinc and
1.2.2 Type II—Zinc plates such as boiler and hull plates produced by any rolling method. —Coils or sheets cut from strip
(ribbon) rolled zinc.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 The issue of each of the following reference documents shall be that which is current on the date the purchase order is
accepted by the supplier (manufacturer).
2
2.2 ASTM Standards:
B899 Terminology Relating to Non-ferrous Metals and Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E60 Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry
E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
E384 Test Method for Knoop and Vickers Hardness of Materials
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E536 Test Methods for Chemical Analysis of Zinc and Zinc Alloys
E634 Practice for Sampling of Zinc and Zinc Alloys for Optical Emission Spectrometric Analysis
3
2.3 ISO Standards:
ISO 3815-1 Zinc and zinc alloys—Part 1: Analysis of solid samples by optical emission spectrometry
ISO 3815-2 Zinc and zinc alloys—Part 2: Analysis by inductively coupled plasma optical emission spectrometry
3. Terminology
3.1 Terms shall be defined in accordance with Terminology B899.
3.2 Definitions of Terms Specific to This Standard:
1
This specification is under the jurisdiction ofASTM Committee B02 on Nonferrous Metals andAlloys and is the direct responsibility of Subcommittee B02.04 on Zinc
and Cadmium.
Current edition approved Oct.July 1, 2010.2011. Published October 2010.July 2011. Originally approved in 1926. Last previous edition approved in 20092010 as
B69-09.B69 - 10. DOI: 10.1520/B0069-101.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B69–11
3.2.1 architectural rolled zinc, Type 1, n—a lower copper composition architectural zinc that exhibits different properties than
Type 2.
3.2.2 architectural rolled zinc, Type 2, n—a higher copper composition architectural zinc that exhibits different properties than
Type 1.
3.2.3 coiled sheet, n—sheet coils with either slit or unslit edges.
3.2.2
3.2.4 flat sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.