ASTM D2823/D2823M-05(2011)e1
(Specification)Standard Specification for Asphalt Roof Coatings, Asbestos Containing (Withdrawn 2014)
Standard Specification for Asphalt Roof Coatings, Asbestos Containing (Withdrawn 2014)
ABSTRACT
This specification covers two types of asbestos-containing asphalt roof coatings consisting of an asphalt base, volatile petroleum solvents, and mineral stabilizers including asbestos fiber, mixed to a smooth, uniform consistency suitable for application by squeegee, three-knot brush, paint brush, roller, or by spraying. Type I is made from asphalts characterized as self-healing, adhesive, and ductile, while Type II is made from asphalts characterized by high softening point and relatively low ductility. The coatings shall comply with specified composition limits of water, nonvolatile matter, asbestos and other mineral stabilizers, asphalt, and mineral matter based on original mass of insoluble residue. They shall also adhere to physical requirements as to uniformity, consistency, and pliability and behavior at given temperatures.
SCOPE
1.1 This specification covers asbestos-containing asphalt roof coatings of brushing or spraying consistency.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covered asbestos-containing asphalt roof coatings of brushing or spraying consistency.
Formerly under the jurisdiction of Committee D08 on Roofing and Waterproofing, this specification was withdrawn in May 2014. This standard is being withdrawn without replacement due to its limited use by industry.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D2823/D2823M −05(Reapproved 2011)
Standard Specification for
Asphalt Roof Coatings, Asbestos-Containing
This standard is issued under the fixed designation D2823/D2823M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
´ NOTE—Units information was editorially revised in June 2011.
1. Scope 4. Classification
4.1 Type I is made from asphalts characterized as self-
1.1 This specification covers asbestos-containing asphalt
roof coatings of brushing or spraying consistency. healing, adhesive, and ductile, and conforming to the require-
ments of Specification D312, Type I; Specification D449,
1.2 The values stated in either SI units or inch-pound units
Types I or II; or Specification D946.
are to be regarded separately as standard. The values stated in
4.2 Type IIis made from asphalts characterized by high
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining softening point and relatively low ductility, and conforming to
the requirements of Specification D312 Types II or III; or
values from the two systems may result in non-conformance
with the standard. Specification D449, Type III.
1.3 This standard does not purport to address all of the
5. Materials and Manufacture
safety concerns, if any, associated with its use. It is the
5.1 Asphalt roof coatings shall consist of an asphalt base,
responsibility of the user of this standard to establish appro-
volatile petroleum solvents, and mineral stabilizers including
priate safety and health practices and determine the applica-
asbestos fiber, mixed to a smooth, uniform consistency suitable
bility of regulatory limitations prior to use.
for application by squeegee, three-knot brush, paint brush,
roller, or by spraying.
2. Referenced Documents
2.1 ASTM Standards: 6. Composition
D312 Specification for Asphalt Used in Roofing
6.1 Asphalt roof coatings complying with this specification
D449 Specification for Asphalt Used in Dampproofing and
shall conform to the following composition limits:
Waterproofing
min max
D946 Specification for Penetration-Graded Asphalt Cement
Water, % . 1.0 (D6511,
for Use in Pavement Construction Section 10)
D1079 Terminology Relating to Roofing and Waterproofing
Nonvolatile matter, % 50 . (D6511,
D6511 Test Methods for Solvent Bearing Bituminous Com-
Section 7)
pounds
Asbestos and other 520 (D6511,
mineral stabilizers, % Section 18)
3. Terminology
Asphalt, % 40 . (D6511,
3.1 For definitions of terms used in this specification, see
Section 18)
Terminology D1079.
Mineral matter based on 80 . (D6511,
original mass of Section 19)
insoluble residue, %
This specification is under the jurisdiction of ASTM Committee D08 on
7. Physical Requirements
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.05
on Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing.
7.1 Uniformity—After a thoroughly stirred sample has stood
Current edition approved May 1, 2011. Published June 2011. Originally
for72hatroomtemperatureinaclosedcontainer,itshallshow
approved in 1969. Last previous edition approved in 2005 as D2823 – 05. DOI:
no separation of solvent or settling that cannot be overcome by
10.1520/D2823_D2823M-05R11E01.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or moderate stirring.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.2 Consistency—The roof coating shall be of a consistency
Standards volume information, refer to t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.