ASTM F1603-17

Standard Specification for Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated

ABSTRACT
This specification covers jacketed kettles using steam as a source of heat for cooking food in commercial and institutional food service establishments. However, it does not cover equipment used by food processors. Covered by this specification are jacketed kettles of various sizes (capacities), grades (Grades 1-3 based on maximum working pressure), styles (Styles 1-5 according to mounting configuration), and classes (Classes A-D based on steam source, whether direct steam or gas-fired or electric steam generator). Kettle and steam jacket shall be manufactured from Type 304, 304L, 316, or 316L corrosion resistant steel. All exterior surfaces of Styles 3-5 kettle stands and bases shall be made of Type 302, 304, 316, or 430 corrosion resistant steel, while those of the kettle mount or support base shall be chrome plated or made of Type 304, 316, or 430 corrosion resistant steel such as for exterior surfaces of console and base of Class B and C kettles. As specified, the kettles shall be provided with the following components: insulation casing, covers and/or operating handles, safety relief valve, swing spout water supply, basket insert, tilt mechanism (hand or crank tilt), kettle mount or support base, control box, safety cut-off, and thermostat. The kettle shall be tested for capacity, heating time, and energy utilization, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers jacketed kettles that use steam as a heat source for cooking food in commercial and institutional food service establishments. This specification does not cover equipment used by food processors who normally package the food that they cook.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Oct-2017
• ICS: 91.140.65 - Water heating equipment
• Technical Committee: F26 - Food Service Equipment
• Drafting Committee: F26.02 - Cooking and Warming Equipment

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1603 − 17 An American National Standard
Standard Specification for
Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L),
Tilting, Table Mounted, Direct Steam, Gas and Electric
1
Heated
This standard is issued under the fixed designation F1603; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope A285/A285M Specification for Pressure Vessel Plates, Car-
bon Steel, Low- and Intermediate-Tensile Strength
1.1 This specification covers jacketed kettles that use steam
A516/A516M Specification for Pressure Vessel Plates, Car-
as a heat source for cooking food in commercial and institu-
bon Steel, for Moderate- and Lower-Temperature Service
tional food service establishments. This specification does not
A580/A580M Specification for Stainless Steel Wire
cover equipment used by food processors who normally
B456 Specification for Electrodeposited Coatings of Copper
package the food that they cook.
Plus Nickel Plus Chromium and Nickel Plus Chromium
1.2 The values stated in inch-pound units are to be regarded
D3951 Practice for Commercial Packaging
as the standard. The values given in parentheses are for
F760 Specification for Food Service Equipment Manuals
information only.
F1166 Practice for Human Engineering Design for Marine
1.3 This standard does not purport to address all of the Systems, Equipment, and Facilities
safety concerns, if any, associated with its use. It is the
F1785 Test Method for Performance of Steam Kettles
4
responsibility of the user of this standard to establish appro- 2.2 ANSI Standards:
priate safety, health, and environmental practices and deter-
ANSI/UL 197 Commercial Electric Cooking Appliances
mine the applicability of regulatory limitations prior to use. ANSI Z83.11 Gas Food Service Equipment—Kettles, Steam
1.4 This international standard was developed in accor-
Cookers and Steam Generators
dance with internationally recognized principles on standard- ANSI/NSF Std. 4 Commercial Cooking and Hot Food Stor-
ization established in the Decision on Principles for the
age Equipment
Development of International Standards, Guides and Recom-
ANSI Z223.1 National Fuel Gas Code
mendations issued by the World Trade Organization Technical ANSI/NFPA 70 National Electrical Code
Barriers to Trade (TBT) Committee.
ANSI Z1.4 Sampling Procedures and Tables for Inspection
by Attributes
5
2. Referenced Documents
2.3 ASME Standards:
2
ASME Boiler and Pressure Vessel Code, Section IV Heating
2.1 ASTM Standards:
Boilers
A176 Specification for Stainless and Heat-Resisting Chro-
3
ASME Boiler and Pressure Vessel Code, Section VIII—
mium Steel Plate, Sheet, and Strip (Withdrawn 2015)
Division 1 Pressure Vessels
A240/A240M Specification for Chromium and Chromium-
6
2.4 Military Standards:
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
MIL-STD-167/1 Mechanical Vibration of Shipboard Equip-
Vessels and for General Applications
ment (Type I—Environmental, and Type II—Internally
Excited)
1
This specification is under the jurisdiction of ASTM Committee F26 on Food
Service Equipment and is the direct responsibility of F26.02 on Cooking and
4
Warming Equipment. Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
Current edition approved Nov. 1, 2017. Published January 2018. Originally 4th Floor, New York, NY 10036, http://www.ansi.org.
5
approved in 1995. Last previous edition approved in 2012 as F1603 – 12. DOI: Available from American Society of Mechanical Engineers (ASME), ASME
10.1520/F1603-17. International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.asme.org.
6
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
Standards volume information, refer to the standard’s Document Summary page on Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS; or Acquisition Stream-
the ASTM website. lining and Standardization Information System (ASSIST) which is the official
3
The last approved version of this historical standard is referenced on www.ast- source of all documents listed in the DoD Index of Specifications and Standards.
m.org. The ASSIST can be located at http://dsp.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1603 − 17
MIL-STD-461 Req
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1603 − 12 F1603 − 17 An American National Standard
Standard Specification for
Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L),
Tilting, Table Mounted, Direct Steam, Gas and Electric
1
Heated
This standard is issued under the fixed designation F1603; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers jacketed kettles that use steam as a heat source for cooking food in commercial and institutional
food service establishments. This specification does not cover equipment used by food processors who normally package the food
that they cook.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
3
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
3
A176 Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip (Withdrawn 2015)
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A285/A285M Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength
A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
A580/A580M Specification for Stainless Steel Wire
B456 Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium
D3951 Practice for Commercial Packaging
F760 Specification for Food Service Equipment Manuals
F1166 Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
F1785 Test Method for Performance of Steam Kettles
4
2.2 ANSI Standards:
ANSI/UL 197 Commercial Electric Cooking Appliances
ANSI Z83.11 Gas Food Service Equipment—Kettles, Steam Cookers and Steam Generators
ANSI/NSF Std. 4 Commercial Cooking and Hot Food Storage Equipment
ANSI Z223.1 National Fuel Gas Code
1
This specification is under the jurisdiction of ASTM Committee F26 on Food Service Equipment and is the direct responsibility of F26.02 on Cooking and Warming
Equipment.
Current edition approved Nov. 1, 2012Nov. 1, 2017. Published December 2012January 2018. Originally approved in 1995. Last previous edition approved in 20072012
as F1603 – 07.F1603 – 12. DOI: 10.1520/F1603-12. 10.1520/F1603-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1603 − 17
ANSI/NFPA 70 National Electrical Code
ANSI Z1.4 Sampling Procedures and Tables for Inspection by Attributes
5
2.3 ASME Standards:
ASME Boiler and Pressure Vessel Code, Section IV Heating Boilers
ASME Boiler and Pressure Vessel Code, Section VIII—Division 1 Pressure Vessels
6
2.4 Military Standards:
MIL-STD-167/1 Mechanical Vibration of Shipboard Equipment (Type I—Environmental, and Type II—Internally Excited)
MIL-STD-461 Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems
...