FprEN 14854

Glass packaging - Dimensions of neck finishes for aerosol and spray glass containers

This document specifies dimensions of neck finishes for aerosol and spray glass containers, in order to guarantee tight sealing of valves or pumps with ferrules defined by EN 14849.
It applies to glass containers with a nominal diameter of the neck finish around 11 mm, 13 mm, 15 mm, 17 mm, 18 mm and 20 mm for both moulded and tubular glass neck finishes.
NOTE   These neck finishes are commonly called FEA 11, 13, 15, 17, 18 and 20.

Verpackungen aus Glas - Maße der Mündungen für Aerosolbehälter und Sprühbehälter aus Glas

Dieses Dokument legt die Maße der Mündungen für Aerosolglasbehälter fest, um einen dichten Abschluss der in EN 14849 definierten Ventile oder Pumpen mit Ventilträgern sicherzustellen.
Es gilt für Glasbehälter mit einem Nenndurchmesser der Mündung von 11 mm, 13 mm, 15 mm, 17 mm, 18 mm und 20 mm für Mündungen bei Hüttenglas und Röhrenglas.
ANMERKUNG   Diese Mündungen werden im Allgemeinen als FEA 11, 13, 15, 17, 18 und 20 bezeichnet.

Emballage en verre - Dimensions des bagues des flacons en verre pour générateurs d'aérosols et pulvérisateurs

Le présent document spécifie les dimensions de la bague des flacons en verre pour générateurs d'aérosols et pulvérisateurs, en vue d’assurer la fermeture étanche des valves ou des pompes équipées des bagues définies dans l’EN 14849.
Il s’applique aux flacons en verre dont la bague mesure environ 11 mm, 13 mm, 15 mm, 17 mm, 18 mm et 20 mm de diamètre nominal, aussi bien pour les bagues en verre moulé que celles en verre tubulaire.
NOTE   Ces bagues sont communément désignées FEA 11, 13, 15, 17, 18 et 20.

Steklena embalaža - Mere vratu za steklene posode za aerosole in razpršila

General Information

• Status: Not Published
• ICS: 55.130 - Aerosol containers
• Technical Committee: CEN/TC 261 - Packaging
• Drafting Committee: CEN/TC 261/SC 5/WG 21 - Glass packaging
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Due Date: 30-Aug-2021
• Completion Date: 30-Aug-2021
• Ref Project: kSIST FprEN 14854:2021 - Glass packaging - Dimensions of neck finishes for aerosol and spray glass containers

RELATIONS

• Revised: EN 14854:2005 - Aerosol containers - Glass containers - Dimensions of the neck finish
• Effective Date: 01-May-2019

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 14854:2020
01-november-2020
Steklena embalaža - Mere vratu za steklene posode za aerosole in razpršila

Glass packaging - Dimensions of neck finishes for aerosol and spray glass containers

Aerosolverpackungen - Glasbehälter - Maße der Mündungen
Récipients pour aérosols - Récipients en verre - Dimensions de la bague du col
Ta slovenski standard je istoveten z: prEN 14854
ICS:
55.130 Pločevinke za aerosole Aerosol containers
oSIST prEN 14854:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 14854:2020
---------------------- Page: 2 ----------------------
oSIST prEN 14854:2020
DRAFT
EUROPEAN STANDARD
prEN 14854
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2020
ICS 55.130 Will supersede EN 14854:2005
English Version
Glass packaging - Dimensions of neck finishes for aerosol
and spray glass containers

Récipients pour aérosols - Récipients en verre - Aerosolverpackungen - Glasbehälter - Maße der

Dimensions de la bague du col Mündungen

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 261.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14854:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 14854:2020
prEN 14854:2020 (E)
Contents Page

European foreword ............................................................................................................................................ 3

1 Scope .......................................................................................................................................................... 4

2 Normative references .......................................................................................................................... 4

3 Terms and definitions ......................................................................................................................... 4

4 Moulded glass ......................................................................................................................................... 4

4.1 Neck finish diameter 13 mm to 20 mm ......................................................................................... 4

4.2 Neck finish diameter 11 mm ............................................................................................................. 7

5 Tubular glass .......................................................................................................................................... 8

Annex A (informative) Symbols .................................................................................................................... 9

Bibliography ....................................................................................................................................................... 10

---------------------- Page: 4 ----------------------
oSIST prEN 14854:2020
prEN 14854:2020 (E)
European foreword

This document (prEN 14854:2020) has been prepared by Technical Committee CEN/TC 261 “Packaging”,

the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14854:2005.

In comparison with the previous edition, the following technical modifications have been made:

— clear separation of the specifications for tubular glass from those for moulded glass;

— the height of the sealing bead on moulded glass only now has tolerances (and therefore the tolerance

of the flange height is slightly increased);

— the dimension F has been recalculated to be more consistent with the finish geometry (driven by

B max) for both moulded and tubular glass;

— addition of some complementary specifications for moulded glass: distance (G) from the lug to under

flange, minimum height (H min) for a standard skirt and some angles and radii;
— introduction of a nomenclature of the specified dimensions.
---------------------- Page: 5 ----------------------
oSIST prEN 14854:2020
prEN 14854:2020 (E)
1 Scope

This document specifies dimensions of neck finishes for aerosol and spray glass containers, in order to

guarantee tight sealing of valves or pumps with ferrules defined by EN 14849.

It applies to glass containers with a nominal diameter of the neck finish around 11 mm, 13 mm, 15 mm,

17 mm, 18 mm and 20 mm for both moulded and tubular glass neck finishes.
NOTE These neck finishes are commonly called FEA 11, 13, 15, 17, 18 and 20.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

• IEC Electropedia: avail
...