prEN ISO 6149-1

Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO/FDIS 6149-1:2022)

This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3.
Ports in accordance with this document can be used at working pressures up to 63 MPa (630 bar[1]) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149‑2 and ISO 6149‑3 for pressure ratings.
NOTE      The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Leitungsanschlüsse für Fluidtechnik und allgemeine Anwendung - Einschraublöcher und Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil 1: Einschraublöcher mit Ansenkung für O-Ring-Abdichtung (ISO/FDIS 6149-1:2022)

Dieses Dokument legt Maße für Einschraublöcher mit metrischem Gewinde für richtungseinstellbare und nicht richtungseinstellbare Einschraubzapfen nach ISO 6149 2 und ISO 6149 3 fest.
Einschraublöcher nach diesem Dokument können bei Arbeitsdrücken bis 63 MPa (630 bar ) mit nicht richtungseinstellbaren Einschraubzapfen und bis 40 MPa (400 bar) mit richtungseinstellbaren Einschraubzapfen verwendet werden. Der zulässige Arbeitsdruck ist abhängig von der Größe des Einschraubloches, den Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendungsfall usw. Druckstufen siehe ISO 6149 2 und ISO 6149 3.
ANMERKUNG   Die Einleitung dieses Dokuments enthält Empfehlungen für die bei Neukonstruktionen in hydraulischen Anlagen der Fluidtechnik zu verwendenden Einschraublöcher und Einschraubzapfen.

Raccordements pour transmissions hydrauliques et applications générales - Orifices et éléments mâles à filetage métrique ISO 261 et joint torique - Partie 1: Orifices à joint torique dans un logement tronconique (ISO/FDIS 6149-1:2022)

Le présent document spécifie les dimensions des orifices métriques pour utilisation avec les éléments mâles orientables et non orientables tels que décrits dans l’ISO 6149-2 et l’ISO 6149-3.
Les orifices conformes au présent document peuvent être utilisés jusqu'à des pressions de travail de 63 MPa (630 bar[1]) pour les éléments mâles non orientables et jusqu’à 40 MPa (400 bar) pour les éléments mâles orientables. La pression de travail admissible dépend de la dimension de l'orifice, des matériaux, de la conception, des conditions de travail, de l'utilisation, etc. Voir l'ISO 6149-2 et l’ISO 6149-3 pour les pressions de travail.
NOTE         L'Introduction du présent document donne des recommandations pour les orifices et les éléments mâles à utiliser pour de nouvelles conceptions dans des applications de transmissions hydrauliques.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Priključki v fluidni tehniki in splošna uporaba - Odprtine in priključki z navoji po ISO 261 in tesnilkami O - 1. del: Odprtine s tesnilko O v koničnem ohišju (ISO/FDIS 6149-1:2022)

General Information

• Status: Not Published
• ICS: 23.100.40 - Piping and couplings
• Technical Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Drafting Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Ref Project: oSIST prEN ISO 6149-1:2022 - Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO/FDIS 6149-1:2022)

RELATIONS

• Revised: EN ISO 6149-1:2019 - Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2019)
• Effective Date: 14-Jul-2021

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN ISO 6149-1:2022
01-april-2022

Priključki v fluidni tehniki in splošna uporaba - Odprtine in priključki z navoji po

ISO 261 in tesnilkami O - 1. del: Odprtine s tesnilko O v koničnem ohišju (ISO/FDIS

6149-1:2022)

Connections for hydraulic fluid power and general use - Ports and stud ends with ISO

261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring

seal (ISO/FDIS 6149-1:2022)

Leitungsanschlüsse für Fluidtechnik und allgemeine Anwendung - Einschraublöcher und

Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil

1: Einschraublöcher mit Ansenkung für O-Ring-Abdichtung (ISO/FDIS 6149-1:2022)

Raccordements pour transmissions hydrauliques et applications générales - Orifices et

éléments mâles à filetage métrique ISO 261 et joint torique - Partie 1: Orifices à joint

torique dans un logement tronconique (ISO/FDIS 6149-1:2022)
Ta slovenski standard je istoveten z: prEN ISO 6149-1
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
oSIST prEN ISO 6149-1:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 6149-1:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6149-1:2022
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 6149-1
ISO/TC 131/SC 4
Connections for hydraulic fluid power
Secretariat: ANSI
and general use — Ports and stud
Voting begins on:
2022-01-28 ends with ISO 261 metric threads and
O-ring sealing —
Voting terminates on:
2022-04-22
Part 1:
Ports with truncated housing for
O-ring seal
Raccordements pour transmissions hydrauliques et applications
générales — Orifices et éléments mâles à filetage métrique ISO 261 et
joint torique —
Partie 1: Orifices à joint torique dans un logement tronconique
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 6149-1:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6149-1:2022
ISO/FDIS 6149-1:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6149-1:2022
ISO/FDIS 6149-1:2022(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction .................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ..................................................................................................................................................................................... 1

3 Terms and definitions .................................................................................................................................................................................... 1

4 Dimensions ................................................................................................................................................................................................................2

5 Interchangeability warning .....................................................................................................................................................................5

6 Test methods ............................................................................................................................................................................................................ 5

7 Designation of ports .........................................................................................................................................................................................5

8 Identification ........................................................................................................................................................................................................... 5

9 Identification statement (reference to this document) .................................................................................................... 5

Bibliography ................................................................................................................................................................................................................................ 6

iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6149-1:2022
ISO/FDIS 6149-1:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee

SC 4, Connectors and similar products and components.

This fourth edition cancels and replaces the third edition (ISO 6149-1:2019), of which it constitutes a

minor revision. The changes is as follows:
— corrections have been made to references in Figure 1 and Table 2.
A list of all the parts in the ISO 6149 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 6149-1:2022
ISO/FDIS 6149-1:2022(E)
Introduction

In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure

within an enclosed circuit. In general applications, a fluid (liquid or gas) may be conveyed under

pressure.

Components are connected through their threaded ports by fluid conductor connectors to tubes and

pipes or to hose connectors and hoses.

Ports are an integral part of fluid power components, i.e. pumps, motors, valves, cylinders.

For threaded ports and stud ends specified in new designs in hydraulic fluid power applications,

ISO/TC 131/SC 4 recommends that the ISO 6149 series be used because these International Standards

specify ports and stud ends with metric threads and O-ring sealing and because the subcommittee

would like to help users by recommending o
...