ETSI TS 103 429 V1.1.1 (2016-07)

Integrated broadband cable telecommunication networks (CABLE); Cable Customer Premises Equipment (CPE) with Integrated Radio and Non-Radio Interfaces; Technical Specification covering the cable equipment technical requirements in support of Harmonised Standards for the essential requirements of article 3.1b of the Directive 2014/53/EU

DTS/CABLE-00023

General Information

• Status: Published
• Publication Date: 18-Jul-2016
• Technical Committee: CABLE WG4 - Network, Fault, Monitoring and Performance Management and Test & Measu
• Current Stage: 12 - Completion
• Due Date: 05-Jul-2016
• Completion Date: 19-Jul-2016

Standards Content (Sample)

ETSI TS 103 429 V1.1.1 (2016-07)






TECHNICAL SPECIFICATION
Integrated broadband cable
telecommunication networks (CABLE);
Cable Customer Premises Equipment (CPE) with
Integrated Radio and Non-Radio Interfaces;
Technical Specification covering the cable equipment
technical requirements in support of
Harmonised Standards for the essential requirements
of article 3.1b of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI TS 103 429 V1.1.1 (2016-07)



Reference
DTS/CABLE-00023
Keywords
CABLE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 103 429 V1.1.1 (2016-07)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 4
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 8
4 Overview of Types of Cable Equipment . 9
5 Relevant Receiver and Transmitter Parameters . 10
5.1 Non-radio function . 10
5.2 Radio Function . 12
6 Primary and Secondary network interfaces . 12
6.1 General . 12
6.2 Functional representation of the cable equipment . 13
7 Test and Measurements . 14
7.1 Introduction . 14
7.2 Test configuration. 14
7.3 Measurements . 15
7.3.1 General . 15
7.3.2 Emission Measurements . 15
7.3.3 Immunity Measurements . 15
Annex A (informative): Bibliography . 16
History . 17


ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 103 429 V1.1.1 (2016-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Integrated broadband cable
telecommunication networks (CABLE).
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
In 2014 the new Radio Equipment directive has been published by the EU commission (Radio Equipment Directive
2014/53/EU, OJ L153 22 May 2014 [i.1]). This directive will replace the existing Radio & Telecommunication
Terminal Equipment Directive (RTTED) 1999/5/EC [i.2]. The new directive has to be implemented into national law
th
before the 13 of June 2016. Before this date, Harmonised Standards need to be developed to be compliant with the new
requirements included in the Directive 2014/53/EU [i.1] such that Cable Customer Premises Equipment (CPE) with
integral non-radio and radio network interfaces compliance to article 3.1 of Directive 2014/53/EU [i.1] may be verified.
The present document applies to Cable CPE with integrated non-radio and radio interfaces.
The schedule for the Radio Equipment Directive 2014/53/EU [i.1] is:
th
• 12 June 2014, RED [i.1] comes into force;
th
• 12 June 2016 is the date by when Member States are required to implement RED [i.1] into their national
laws;
• July 2017 is a transition period for RED [i.1] during which period the RTTED [i.2] may still be used i.e. one
year transition period.
th
A new product entering the market after the 13 June 2016 is required to meet the requirements of RED [i.1].
The RED [i.1] is replacing the RTTED [i.2], however as the name implies, RTTE has become RE (no more 'TTE')
therefore Telecom Terminal Equipment (TTE), has been removed from the Radio Equipment Directive:
• Cable modems and cable receiver equipment with a non-radio network interface i.e. fixed line cable RF
network interface, will continue to have to comply with all other applicable Directives. In terms of the
Directives EMC [i.3] and LVD [i.4].
• New LVD [i.4] and EMC Directives [i.3] apply from 20 April 2016.
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 103 429 V1.1.1 (2016-07)
®
NOTE: DOCSIS is a registered Trade Mark of Cable Television Laboratories, Inc., and is used in the present
document with permission.

ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 103 429 V1.1.1 (2016-07)
1 Scope
The present document provides technical requirements for cable CPE with integrated radio and non-radio interfaces in
support of Harmonised Standards for the essential requirements of article 3.1b of the Radio Equipment Directive
2014/53/EU [i.1].
Cable equipment comprises integrated non-radio and radio network interfaces. These functions are integrated either on
the same integrated electronic components on the same printed circuit board or by separate integrated components on
the same printed circuit boards but housed in the same equipment enclosure. The non-radio function is the Cable RF as
specified by ETSI EN 302 878-2 [1] for data communication services and by ETSI EN 300 429 [2] for video
communication services. The radio function is a wireless local area network operating in the 2,4 GHz and 5 GHz
frequency bands according to IEEE 802.11 [3].
NOTE: Cable equipment does not comprise separate radio and non-radio products that are combined in one
enclosure. Where cable equipment of this type exist then the essential requirements of article 3.1b of
Directive 2014/53/EU [i.1] apply to the equipment and the equipment requirements are as specified by
ETSI draft harmonised standard ETSI EN 303 446-1 [i.5], at the time of writing it is under development
ETSI TC ERM WGEMC.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 302 878-2: "Access, Terminals, Transmission and Multiplexing (ATTM); Third
Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems;
Part 2: Physical Layer; DOCSIS 3.0".
[2] ETSI EN 300 429: "Digital Video Broadcasting (DVB); Framing structure, channel coding and
modulation for cable systems".
[3] IEEE 802.11™-2012: "IEEE Standard for Information Technology - Telecommunications and
information exchange between systems - Local and metropolitan area networks - Specific
requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications".
[4] ETSI EN 302 878-3: "Access, Terminals, Transmission and Multiplexing (ATTM); Third
Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems;
Part 3: Downstream Radio Frequency Interface; DOCSIS 3.0".
[5] CENELEC EN 60728-1: "Cable networks for television signals, sound signals and interactive
services - Part 1: System performance of forward paths".
[6] ETSI EN 301 489-1: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Harmonised Standard covering the essential requirements of article 3.1(b) of the
Directive 2014/53/EU and the essential requirements of article 6 of the Directive 2014/30/EU;
Part 1: Common technical requirements".
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TS 103 429 V1.1.1 (2016-07)
[7] ETSI EN 301 489-17: "ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for Broadband Data Transmission Systems; Harmonised
Standard covering the essential requirements of article 3.1(b) of the Directive 2014/53/EU".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity.
[i.3] Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the
harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast).
[i.4] Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
electrical equipment designed for use within certain voltage limits (recast).
[i.5] ETSI EN 303 446-1: "ElectroMagnetic Compatibility (EMC) Standard for radio equipment and
services; Part 60: Specific conditions for combined radio and non-radio equipment in the domestic
environment. Harmonised Standard covering the essential requirements of article 3.1(b) of the
Directive 2014/53/EU".
[i.6] IEEE 802.11b™: "IEEE Standard for Information Technology - Telecommunications and
information exchange between systems - Local and Metropolitan area networks - Specific
requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
specifications: Higher Speed Physical Layer (PHY) Extension in the 2.4 GHz band".
[i.7] IEEE 802.11g™: "IEEE Standard for Information Technology - Telecommunications and
information exchange between systems - Local and Metropolitan Area Networks - Specific
Requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications: Further Higher Data Rate Extension in the 2.4 GHz Band".
[i.8] IEEE 802.11n™: "IEEE Standard for Information technology -- Local and metropolitan area
networks -- Specific requirements -- Part 11: Wireless LAN Medium Access Control (MAC) and
Physical Layer (PHY) Specifications Amendment 5: Enhancements for Higher Throughput".
[i.9] IEEE 802.11a™: "IEEE Standard for Information Technology - Telecommunications and
information exchange between systems - Local and Metropolitan area networks - Specific
requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
specifications: High Speed Physical Layer in the 5 GHz band".
[i.10] CM-SP-CMCIv3.0-I02-140729: "Cable Modem to Customer Premise Equipment Interface
Specification".
[i.11] ETSI TS 103 161-14: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 14: Embedded MTA Analog
Interface and Powering Specification".
ETSI

---------------------- Page: 7 ----------------------
8 ETSI TS 103 429 V1.1.1 (2016-07)
[i.12] IEEE 802.11ac™: "IEEE Standard for Information technology -- Telecommunications and
information exchange between systems - Local and metropolitan area networks -- Specific
requirements -- Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
Specifications -- Amendment 4: Enhancements for Very High Throughput for Operation in Bands
below 6 GHz".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
Bluetooth™ system: equipment in compliance with Bluetooth™ specification
TM
NOTE: Bluetooth is an example of a suitable product available commercially. This information is given for the
convenience of users of the present document and does not constitute an endorsement by ETSI of this
product.
combined equipment: any combination of non-radio equipment t
...