ETSI EN 301 441 V2.1.1 (2016-06)

Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES), including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) operating in the 1,6 GHz/2,4 GHz frequency band under the Mobile Satellite Service (MSS) covering the essential requirements of article 3.2 of the Directive 2014/53/EU

REN/SES-00383

Satelitske zemeljske postaje in sistemi (SES) - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU, za mobilne zemeljske postaje (MES), vključno z ročnimi zemeljskimi postajami za S-PCN, ki delujejo v frekvenčnem pasu 1,6 GHz/2,4 GHz, pri mobilnih satelitskih storitvah (MSS)

Ta dokument se uporablja za radijsko opremo mobilnih zemeljskih postaj (MES) z naslednjimi značilnostmi:
• Te mobilne zemeljske postaje imajo sposobnost oddajanja in sprejemanja ter delujejo v satelitskem osebnem komunikacijskem omrežju (S-PCN). Satelitsko osebno komunikacijsko omrežje mobilne zemeljske postaje je lahko ročna prenosna oprema, ki je pritrjena ali polpritrjena na vozilo in povezana z gostiteljem, ali je element v večnačinovnem terminalu. Sestavljeno je lahko iz več modulov s povezanimi priključki in uporabniškim vmesnikom ali je samozadostna enota.
• Če je mobilna zemeljska postaja element v večnačinovnem terminalu, zahteve tega dokumenta veljajo samo za satelitsko osebno komunikacijsko omrežje zemeljske mobilne postaje v terminalu, razen če je v dokumentu drugače navedeno.
• Te mobilne zemeljske postaje lahko delujejo v vseh frekvenčnih pasovih iz preglednice 1 ali njihovem delu.
Ta dokument zajema določbe člena 3.2 Direktive 2014/53/EU [10] (direktive RE), ki navaja: »/.../ Radijska oprema je izdelana tako, da optimalno uporablja in podpira učinkovito izrabo radijskega spektra, z namenom preprečevanja škodljivega motenja.«
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 Direktive 2014/53/EU [10].
OPOMBA 1: seznam tovrstnih standardov EN je na voljo na spletnem mestu inštituta ETSI.
OPOMBA 2: te kopenske mobilne zemeljske postaje se krmilijo in spremljajo z napravo za krmiljenje omrežja (NCF). Naprava za krmiljenje omrežja ne spada v področje uporabe tega dokumenta.

General Information

• Status: Published
• Publication Date: 11-Apr-2017
• Technical Committee: SES HARM - SES WG on R&TTE dir. 99/5/EC and and RED dir. 2014/53/EU
• Current Stage: 12 - Citation in the OJ
• Due Date: 09-Sep-2016
• Completion Date: 12-Apr-2017
• Ref Project: SIST EN 301 441 V2.1.1:2016 - Satellite Earth Stations and Systems (SES) - Harmonised Standard for Mobile Earth Stations (MESs), including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) operating in the 1,6 GHz/2,4 GHz frequency band under the Mobile Satellite Service (MSS) covering essential requirements of article 3.2 of the Directive 2014/53/EU

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Satellite Earth Stations and Systems (SES) - Harmonised Standard for Mobile Earth Stations (MESs), including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) operating in the 1,6 GHz/2,4 GHz frequency band under the Mobile Satellite Service (MSS) covering essential requirements of article 3.2 of the Directive 2014/53/EU33.070.99Druge mobilne storitveOther mobile services33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:ETSI EN 301 441 V2.1.1 (2016-06)SIST EN 301 441 V2.1.1:2016en01-september-2016SIST EN 301 441 V2.1.1:2016SLOVENSKI
STANDARD



SIST EN 301 441 V2.1.1:2016



ETSI EN 301 441 V2.1.1 (2016-06) Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES), including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) operating in the 1,6 GHz/2,4 GHz frequency band under the Mobile Satellite Service (MSS) covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 2
Reference REN/SES-00383 Keywords earth station, MES, MSS, regulation, satellite, S-PCN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Introduction . 6 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions and abbreviations . 9 3.1 Definitions . 9 3.2 Abbreviations . 11 4 Technical requirement specifications . 12 4.1 Environment profile . 12 4.1.1 General . 12 4.1.2 Temperature . 12 4.1.3 Voltage . 12 4.1.4 Vibration . 12 4.2 Conformance requirements . 12 4.2.1 Unwanted emissions outside the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 12 4.2.1.1 Justification . 12 4.2.1.2 Technical requirements . 12 4.2.1.3 Conformance test . 13 4.2.2 Unwanted emissions within the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 13 4.2.2.1 Justification . 13 4.2.2.2 Technical requirements . 13 4.2.2.3 Conformance test . 14 4.2.3 EIRP density within the operational band. 15 4.2.3.1 Justification . 15 4.2.3.2 Technical requirements . 15 4.2.3.3 Conformance test . 15 4.2.4 Unwanted emissions in carrier-off state . 15 4.2.4.1 Justification . 15 4.2.4.2 Technical requirements . 15 4.2.4.3 Conformance test . 15 4.2.5 MES Control and Monitoring Functions (CMF) . 16 4.2.5.1 Self-monitoring functions / Processor monitoring . 16 4.2.5.1.1 Justification . 16 4.2.5.1.2 Technical requirements. 16 4.2.5.1.3 Conformance test . 16 4.2.5.2 Self-monitoring functions / Transmit frequency generation sub-system monitoring . 16 4.2.5.2.1 Justification . 16 4.2.5.2.2 Technical requirements. 16 4.2.5.2.3 Conformance test . 16 4.2.5.3 Network control authorization . 16 4.2.5.3.1 Justification . 16 4.2.5.3.2 Technical requirements. 16 4.2.5.3.3 Conformance test . 17 4.2.5.4 Network control reception . 17 4.2.5.4.1 Transmission disable/enable . 17 4.2.5.4.2 Transmit frequency control . 17 4.2.5.5 Fellow radio stations in a dual-mode or multi-mode terminal . 18 4.2.5.5.1 Justification . 18 SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 4 4.2.5.5.2 Technical requirements. 18 4.2.5.5.3 Conformance test . 18 4.2.6 Equipment identity . 18 4.2.6.1 Justification . 18 4.2.6.2 Technical requirements . 18 4.2.6.3 Conformance test . 18 4.2.7 Protection of the radio astronomy service operation in the band 1 610,6 MHz to 1 613,8 MHz . 18 4.2.7.1 Justification . 18 4.2.7.2 Technical requirements . 18 4.2.7.3 Conformance test . 18 4.2.8 Receiver Adjacent Channel Selectivity. 19 4.2.8.1 Justification . 19 4.2.8.2 Technical requirements . 19 4.2.8.3 Conformance test . 19 4.2.9 Receiver Blocking Characteristics . 19 4.2.9.1 Justification . 19 4.2.9.2 Technical requirements . 19 4.2.9.3 Conformance test . 20 5 Testing for compliance with technical requirements . 20 5.1 Environmental conditions for testing . 20 5.1.1 Specification of the environmental test conditions . 20 5.1.2 Tests under extreme voltage conditions . 20 5.2 Essential radio test suites . 20 5.2.1 General . 20 5.2.1.1 Presentation of equipment for testing purposes. 20 5.2.1.2 Description of equipment . 21 5.2.1.3 Testing of host-connected equipment and plug-in modules . 21 5.2.1.3.1 Alternative approaches . 21 5.2.1.3.2 Alternative A: combined equipment . 21 5.2.1.3.3 Alternative B: use of a test jig . 22 5.2.1.4 CMF / Special Test Equipment (STE) . 22 5.2.1.5 General test requirements . 22 5.2.1.5.1 MES test modes . 22 5.2.1.5.2 Special Test Equipment (STE) . 23 5.2.1.5.3 Laboratory Test Equipment (LTE) . 23 5.2.1.5.4 Methods of test for MES RF emissions according to the equipment type . 24 5.2.1.5.5 Procedures for measurement of radiated emissions . 24 5.2.1.5.6 Procedures for measurement of conducted emissions . 29 5.2.1.5.7 Interpretation of the measurement results . 30 5.2.1.5.8 Test report . 30 5.2.2 Unwanted emissions outside the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 30 5.2.2.1 Method of test . 30 5.2.2.2 Peak measurement . 31 5.2.2.3 Average measurement . 31 5.2.2.4 Test requirements . 32 5.2.3 Unwanted emissions within the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to 1 628,5 MHz (carrier-on) . 32 5.2.3.1 Method of test . 32 5.2.3.2 Measurement method . 32 5.2.3.3 Test requirements . 33 5.2.4 EIRP density within the operational band. 33 5.2.4.1 Method of test . 33 5.2.4.2 Peak limit test . 33 5.2.4.3 Mean limit test . 34 5.2.4.4 Test requirements . 34 5.2.5 Unwanted emissions in carrier-off state . 34 5.2.5.1 Method of test . 34 5.2.5.2 Measurement method . 35 5.2.5.3 Test requirements . 35 5.2.6 MES Control and Monitoring Functions (CMF) . 35 SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 5 5.2.6.1 Self-monitoring functions / Processor monitoring . 35 5.2.6.2 Self-monitoring functions / Transmit frequency generation sub-system monitoring . 35 5.2.6.3 Network control authorization . 35 5.2.6.3.1 Method of test . 35 5.2.6.3.2 Test procedure . 35 5.2.6.3.3 Test requirement . 36 5.2.6.4 Network control reception . 36 5.2.6.4.1 Transmission disable/enable . 36 5.2.6.4.2 Transmit frequency control . 37 5.2.6.5 Fellow radio stations in a dual-mode or multi-mode terminal . 37 5.2.6.5.1 Method of test . 37 5.2.6.5.2 Test procedure . 38 5.2.6.5.3 Test requirements . 38 5.2.7 Equipment identity . 38 5.2.7.1 Method of test . 38 5.2.7.2 Test procedure . 38 5.2.7.3 Test requirements . 38 5.2.8 Receiver Adjacent Channel Selectivity. 38 5.2.8.1 General . 38 5.2.8.2 Test set-up . 38 5.2.8.3 Test procedure . 39 5.2.9 Receiver Blocking Characteristics . 39 5.2.9.1 General . 39 5.2.9.2 Test set-up . 39 5.2.9.3 Test procedure . 39 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 41 Annex B (informative): Explanation of nominated bandwidth . 43 B.1 Introduction . 43 B.2 Interpretation of Parameters [Bn, fc, a, b] . 43 B.3 Choice of nominated bandwidth . 43 B.4 Maximum value for nominated bandwidth . 45 Annex C (informative): Bibliography . 48 History . 49
SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [10]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations.
National transposition dates Date of adoption of this EN: 16 May 2016 Date of latest announcement of this EN (doa): 31 August 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
28 February 2017 Date of withdrawal of any conflicting National Standard (dow): 28 February 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction ETSI has designed a modular structure for the standards. Each standard is a module in the structure. The modular structure is shown in ETSI EG 201 399 [i.1] Figure 1: Void SIST EN 301 441 V2.1.1:2016



ETSI ETSI EN 301 441 V2.1.1 (2016-06) 7 The present document is based on ETSI TBR 041 [4]. The technical requirements in the present document are applied under articles 3.2 of the Directive 2014/53/EU [10], concerning the effective uses of the spectrum allocated to terrestrial/space radio communication and orbital resources so as to avoid harmful interference.
These requirements are in two major categories: emissions limits: to protect other radio services from harmful interference generated by the MES in normal use. MES Control and Monitoring Functions (CMF): to protect other radio services from unwanted transmissions from the MES. The CMF in each MES is capable of answering to commands from the Network Control Facilities (NCF) for its S-PCN. Receiver performance specifications: to enable reception of a wanted signal in the presence of other high power signals in the adjacent channel and/or adjacent band. NOTE: The requirements for Network Control Facilities (NC
...

ETSI EN 301 441 V2.1.1 (2016-06)






HARMONISED EUROPEAN STANDARD
Satellite Earth Stations and Systems (SES);
Harmonised Standard for Mobile Earth Stations (MES),
including handheld earth stations, for Satellite Personal
Communications Networks (S-PCN) operating in the
1,6 GHz/2,4 GHz frequency band under the Mobile Satellite
Service (MSS) covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 301 441 V2.1.1 (2016-06)



Reference
REN/SES-00383
Keywords
earth station, MES, MSS, regulation, satellite,
S-PCN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 441 V2.1.1 (2016-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 11
4 Technical requirement specifications . 12
4.1 Environment profile . 12
4.1.1 General . 12
4.1.2 Temperature . 12
4.1.3 Voltage . 12
4.1.4 Vibration . 12
4.2 Conformance requirements . 12
4.2.1 Unwanted emissions outside the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to
1 628,5 MHz (carrier-on) . 12
4.2.1.1 Justification . 12
4.2.1.2 Technical requirements . 12
4.2.1.3 Conformance test . 13
4.2.2 Unwanted emissions within the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to
1 628,5 MHz (carrier-on) . 13
4.2.2.1 Justification . 13
4.2.2.2 Technical requirements . 13
4.2.2.3 Conformance test . 14
4.2.3 EIRP density within the operational band. 15
4.2.3.1 Justification . 15
4.2.3.2 Technical requirements . 15
4.2.3.3 Conformance test . 15
4.2.4 Unwanted emissions in carrier-off state . 15
4.2.4.1 Justification . 15
4.2.4.2 Technical requirements . 15
4.2.4.3 Conformance test . 15
4.2.5 MES Control and Monitoring Functions (CMF) . 16
4.2.5.1 Self-monitoring functions / Processor monitoring . 16
4.2.5.1.1 Justification . 16
4.2.5.1.2 Technical requirements. 16
4.2.5.1.3 Conformance test . 16
4.2.5.2 Self-monitoring functions / Transmit frequency generation sub-system monitoring . 16
4.2.5.2.1 Justification . 16
4.2.5.2.2 Technical requirements. 16
4.2.5.2.3 Conformance test . 16
4.2.5.3 Network control authorization . 16
4.2.5.3.1 Justification . 16
4.2.5.3.2 Technical requirements. 16
4.2.5.3.3 Conformance test . 17
4.2.5.4 Network control reception . 17
4.2.5.4.1 Transmission disable/enable . 17
4.2.5.4.2 Transmit frequency control . 17
4.2.5.5 Fellow radio stations in a dual-mode or multi-mode terminal . 18
4.2.5.5.1 Justification . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 441 V2.1.1 (2016-06)
4.2.5.5.2 Technical requirements. 18
4.2.5.5.3 Conformance test . 18
4.2.6 Equipment identity . 18
4.2.6.1 Justification . 18
4.2.6.2 Technical requirements . 18
4.2.6.3 Conformance test . 18
4.2.7 Protection of the radio astronomy service operation in the band 1 610,6 MHz to 1 613,8 MHz . 18
4.2.7.1 Justification . 18
4.2.7.2 Technical requirements . 18
4.2.7.3 Conformance test . 18
4.2.8 Receiver Adjacent Channel Selectivity. 19
4.2.8.1 Justification . 19
4.2.8.2 Technical requirements . 19
4.2.8.3 Conformance test . 19
4.2.9 Receiver Blocking Characteristics . 19
4.2.9.1 Justification . 19
4.2.9.2 Technical requirements . 19
4.2.9.3 Conformance test . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.1.1 Specification of the environmental test conditions . 20
5.1.2 Tests under extreme voltage conditions . 20
5.2 Essential radio test suites . 20
5.2.1 General . 20
5.2.1.1 Presentation of equipment for testing purposes. 20
5.2.1.2 Description of equipment . 21
5.2.1.3 Testing of host-connected equipment and plug-in modules . 21
5.2.1.3.1 Alternative approaches . 21
5.2.1.3.2 Alternative A: combined equipment . 21
5.2.1.3.3 Alternative B: use of a test jig . 22
5.2.1.4 CMF / Special Test Equipment (STE) . 22
5.2.1.5 General test requirements . 22
5.2.1.5.1 MES test modes . 22
5.2.1.5.2 Special Test Equipment (STE) . 23
5.2.1.5.3 Laboratory Test Equipment (LTE) . 23
5.2.1.5.4 Methods of test for MES RF emissions according to the equipment type . 24
5.2.1.5.5 Procedures for measurement of radiated emissions . 24
5.2.1.5.6 Procedures for measurement of conducted emissions . 29
5.2.1.5.7 Interpretation of the measurement results . 30
5.2.1.5.8 Test report . 30
5.2.2 Unwanted emissions outside the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to
1 628,5 MHz (carrier-on) . 30
5.2.2.1 Method of test . 30
5.2.2.2 Peak measurement . 31
5.2.2.3 Average measurement . 31
5.2.2.4 Test requirements . 32
5.2.3 Unwanted emissions within the band 1 610 MHz to 1 626,5 MHz and the band 1 626,5 MHz to
1 628,5 MHz (carrier-on) . 32
5.2.3.1 Method of test . 32
5.2.3.2 Measurement method . 32
5.2.3.3 Test requirements . 33
5.2.4 EIRP density within the operational band. 33
5.2.4.1 Method of test . 33
5.2.4.2 Peak limit test . 33
5.2.4.3 Mean limit test . 34
5.2.4.4 Test requirements . 34
5.2.5 Unwanted emissions in carrier-off state . 34
5.2.5.1 Method of test . 34
5.2.5.2 Measurement method . 35
5.2.5.3 Test requirements . 35
5.2.6 MES Control and Monitoring Functions (CMF) . 35
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 441 V2.1.1 (2016-06)
5.2.6.1 Self-monitoring functions / Processor monitoring . 35
5.2.6.2 Self-monitoring functions / Transmit frequency generation sub-system monitoring . 35
5.2.6.3 Network control authorization . 35
5.2.6.3.1 Method of test . 35
5.2.6.3.2 Test procedure . 35
5.2.6.3.3 Test requirement . 36
5.2.6.4 Network control reception . 36
5.2.6.4.1 Transmission disable/enable . 36
5.2.6.4.2 Transmit frequency control . 37
5.2.6.5 Fellow radio stations in a dual-mode or multi-mode terminal . 37
5.2.6.5.1 Method of test . 37
5.2.6.5.2 Test procedure . 38
5.2.6.5.3 Test requirements . 38
5.2.7 Equipment identity . 38
5.2.7.1 Method of test . 38
5.2.7.2 Test procedure . 38
5.2.7.3 Test requirements . 38
5.2.8 Receiver Adjacent Channel Selectivity. 38
5.2.8.1 General . 38
5.2.8.2 Test set-up . 38
5.2.8.3 Test procedure . 39
5.2.9 Receiver Blocking Characteristics . 39
5.2.9.1 General . 39
5.2.9.2 Test set-up . 39
5.2.9.3 Test procedure . 39
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 41
Annex B (informative): Explanation of nominated bandwidth . 43
B.1 Introduction . 43
B.2 Interpretation of Parameters [Bn, f , a, b] . 43
c
B.3 Choice of nominated bandwidth . 43
B.4 Maximum value for nominated bandwidth . 45
Annex C (informative): Bibliography . 48
History . 49

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 441 V2.1.1 (2016-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Satellite Earth Stations
and Systems (SES).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [10].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 16 May 2016
Date of latest announcement of this EN (doa): 31 August 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2017
Date of withdrawal of any conflicting National Standard (dow): 28 February 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
ETSI has designed a modular structure for the standards. Each standard is a module in the structure. The modular
structure is shown in ETSI EG 201 399 [i.1]
Figure 1: Void
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 441 V2.1.1 (2016-06)
The present document is based on ETSI TBR 041 [4].
The technical requirements in the present document are applied under articles 3.2 of the Directive 2014/53/EU [10],
concerning the effective uses of the spectrum allocated to terrestrial/space radio communication and orbital resources so
as to avoid harmful interference.
These requirements are in two major categories:
emissions limits: to protect other radio services from harmful interference generated by the MES in normal use.
MES Control and Monitoring Functions (CMF): to protect other radio services from unwanted transmissions from
the MES. The CMF in each MES is capable of answering to commands from the Network Control Facilities (NCF) for
its S-PCN.
Receiver performance specifications: to enable reception of a wanted signal in the presence of other high power
signals in the adjacent channel and/or adjacent band.
NOTE: The requirements for Network Control Facilities (NCF) for S-PCN are contained in ETSI
ETS 300 735 [5].
The determination of the parameters of the user earth stations using a given satellite constellation for the protection of
the spectrum allocated to that satellite constellation, is considered to be under the responsibility of the satellite operator
or the satellite network operators.
ETSI

---------------------- Page
...