ETSI EN 302 567 V2.2.1 (2021-07)

Multiple-Gigabit/s radio equipment operating in the 60 GHz band; Harmonised Standard for access to radio spectrum

REN/BRAN-230018

Večgigabitna radijska oprema, ki deluje v pasu 60 GHz - Harmonizirani standard za dostop do radijskega spektra

General Information

• Status: Not Published
• Technical Committee: BRAN - Broadband Radio Access Networks
• Current Stage: 12 - Citation in the OJ
• Due Date: 06-Jan-2022
• Completion Date: 29-Mar-2022
• Ref Project: SIST EN 302 567 V2.2.1:2021 - Multiple-Gigabit/s radio equipment operating in the 60 GHz band - Harmonised Standard for access to radio spectrum

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 302 567 V2.2.1:2021
01-september-2021
Večgigabitna radijska oprema, ki deluje v pasu 60 GHz - Harmonizirani standard za
dostop do radijskega spektra
Multiple-Gigabit/s radio equipment operating in the 60 GHz band - Harmonised Standard
for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 302 567 V2.2.1 (2021-07)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
35.110 Omreževanje Networking
SIST EN 302 567 V2.2.1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 302 567 V2.2.1:2021

---------------------- Page: 2 ----------------------
SIST EN 302 567 V2.2.1:2021
ETSI EN 302 567 V2.2.1 (2021-07)






HARMONISED EUROPEAN STANDARD
Multiple-Gigabit/s radio equipment
operating in the 60 GHz band;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
SIST EN 302 567 V2.2.1:2021

2 ETSI EN 302 567 V2.2.1 (2021-07)

Reference
REN/BRAN-230018
Keywords
access, broadband, LAN, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
SIST EN 302 567 V2.2.1:2021

3 ETSI EN 302 567 V2.2.1 (2021-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Spectral power density . 11
4.2.1.0 Applicability. 11
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 12
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Receiver unwanted emissions . 13
4.2.4.0 Applicability. 13
4.2.4.1 Definition . 13
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Requirement . 13
4.2.5.4 Conformance . 14
4.2.6 Short Control Signalling Transmissions . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limits . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver Adjacent Channel Rejection . 14
4.2.7.1 Applicability. 14
4.2.7.2 Definition . 15
4.2.7.3 Performance Criteria . 15
4.2.7.4 Limits . 15
4.2.7.5 Conformance . 15
4.2.8 Transmitter unwanted emissions in the out-of-band domain . 15
4.2.8.0 Applicability. 15
4.2.8.1 Definition . 15
ETSI

---------------------- Page: 5 ----------------------
SIST EN 302 567 V2.2.1:2021

4 ETSI EN 302 567 V2.2.1 (2021-07)
4.2.8.2 Limit . 15
4.2.8.3 Conformance . 16
4.2.9 Void . 16
4.2.10 Occupied Channel Bandwidth . 16
4.2.10.1 Applicability. 16
4.2.10.2 Definition . 16
4.2.10.3 Requirements . 16
4.2.10.4 Conformance . 16
4.2.11 Receiver Sensitivity level . 17
4.2.11.1 Applicability. 17
4.2.11.2 Definition . 17
4.2.11.3 Limits . 17
4.2.11.4 Conformance . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 18
5.2 Void . 18
5.3 Test procedure for the essential radio test suites . 18
5.3.0 General . 18
5.3.1 Product Information . 18
5.3.2 Test modulation, frequency and configuration . 18
5.3.3 Spectral power density . 19
5.3.3.1 Test conditions . 19
5.3.3.2 Test method . 19
5.3.4 RF output power . 20
5.3.4.1 Test conditions . 20
5.3.4.2 Test method . 20
5.3.5 Transmitter unwanted emissions in the spurious domain . 21
5.3.5.0 Test conditions . 21
5.3.5.1 Pre-scan . 21
5.3.5.2 Identified emissions . 22
5.3.6 Receiver unwanted emissions . 23
5.3.6.0 Test conditions . 23
5.3.6.1 Pre-scan . 23
5.3.6.2 Identified emissions . 23
5.3.7 Receiver Adjacent Channel Rejection . 24
5.3.7.1 Test conditions . 24
5.3.7.2 Test Method . 24
5.3.8 Adaptivity (medium access protocol) . 25
5.3.8.1 Test conditions . 25
5.3.8.2 Test method . 25
5.3.8.3 Generic test procedure for measuring channel/frequency usage . 27
5.3.9 Transmitter unwanted emissions in the out-of-band domain . 28
5.3.9.1 Test conditions . 28
5.3.9.2 Test method . 28
5.3.10 Occupied Channel Bandwidth . 29
5.3.10.1 Test conditions . 29
5.3.10.2 Test method . 29
5.3.11 Receiver sensitivity level . 29
5.3.11.1 Test conditions . 29
5.3.11.2 Test method . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): Maximum Measurement Uncertainty . 33
ETSI

---------------------- Page: 6 ----------------------
SIST EN 302 567 V2.2.1:2021

5 ETSI EN 302 567 V2.2.1 (2021-07)
Annex C (normative): Test sites and arrangements for radiated measurements . 34
C.1 Test sites . 34
C.1.1 Open air test sites . 34
C.1.2 Anechoic chamber . 35
C.1.2.1 General . 35
C.1.2.2 Description . 35
C.1.2.3 Influence of parasitic reflections . 35
C.1.2.4 Calibration and mode of use . 35
C.2 Test antenna . 37
C.3 Substitution antenna . 37
Annex D (normative): General description of measurement . 38
D.1 Radiated measurements . 38
D.2 Substitution measurement . 39
Annex E (informative): Bibliography . 40
Annex F (informative): Change History . 41
History . 42

ETSI

---------------------- Page: 7 ----------------------
SIST EN 302 567 V2.2.1:2021

6 ETSI EN 302 567 V2.2.1 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.6].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 5 July 2021
Date of latest announcement of this EN (doa): 31 October 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2022
Date of withdrawal of any conflicting National Standard (dow): 30 April 2023

ETSI

---------------------- Page: 8 ----------------------
SIST EN 302 567 V2.2.1:2021

7 ETSI EN 302 567 V2.2.1 (2021-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
60 GHz radio equipment are capable of operating at data rates of multiple-gigabit per second.
The spectrum usage conditions for this equipment are set in Commission Decision 2013/752/EU [i.4] and Commission
Decision 2019/1345/EU [i.7] amending Commission Decision 2006/771/EC of 9 November 2006 [i.5] and ERC
Recommendation 70-03 [i.3], annex 3.
ETSI

---------------------- Page: 9 ----------------------
SIST EN 302 567 V2.2.1:2021

8 ETSI EN 302 567 V2.2.1 (2021-07)
1 Scope
The present document specifies technical characteristics and methods of measurements for radio equipment with
integral antennas operating indoor or outdoor at data rates of multiple-gigabit per second in the 60 GHz frequency
range.
These radio equipment operate with very wideband communications using a variety of directional medium and high
gain antennas to enable a high degree of spectrum reuse, and may use a flexible bandwidth scheme under which they
normally operate in a wideband mode, and periodically reduce their bandwidth (e.g. for antenna training and other
activities).
The technical characteristics of applications using these radio equipment are further described in ETSI TR 102 555 [i.1].
Equipment in this frequency range intended for outdoor Fixed Local Area Network Extension (FLANE) or Fixed
Point-to-Point applications are not in the scope of the present document.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Radiocommunications service frequency band
Trans
...

ETSI EN 302 567 V2.2.1 (2021-07)






HARMONISED EUROPEAN STANDARD
Multiple-Gigabit/s radio equipment
operating in the 60 GHz band;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 ETSI EN 302 567 V2.2.1 (2021-07)

Reference
REN/BRAN-230018
Keywords
access, broadband, LAN, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 302 567 V2.2.1 (2021-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Spectral power density . 11
4.2.1.0 Applicability. 11
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 12
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Receiver unwanted emissions . 13
4.2.4.0 Applicability. 13
4.2.4.1 Definition . 13
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Requirement . 13
4.2.5.4 Conformance . 14
4.2.6 Short Control Signalling Transmissions . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limits . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver Adjacent Channel Rejection . 14
4.2.7.1 Applicability. 14
4.2.7.2 Definition . 15
4.2.7.3 Performance Criteria . 15
4.2.7.4 Limits . 15
4.2.7.5 Conformance . 15
4.2.8 Transmitter unwanted emissions in the out-of-band domain . 15
4.2.8.0 Applicability. 15
4.2.8.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 302 567 V2.2.1 (2021-07)
4.2.8.2 Limit . 15
4.2.8.3 Conformance . 16
4.2.9 Void . 16
4.2.10 Occupied Channel Bandwidth . 16
4.2.10.1 Applicability. 16
4.2.10.2 Definition . 16
4.2.10.3 Requirements . 16
4.2.10.4 Conformance . 16
4.2.11 Receiver Sensitivity level . 17
4.2.11.1 Applicability. 17
4.2.11.2 Definition . 17
4.2.11.3 Limits . 17
4.2.11.4 Conformance . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 18
5.2 Void . 18
5.3 Test procedure for the essential radio test suites . 18
5.3.0 General . 18
5.3.1 Product Information . 18
5.3.2 Test modulation, frequency and configuration . 18
5.3.3 Spectral power density . 19
5.3.3.1 Test conditions . 19
5.3.3.2 Test method . 19
5.3.4 RF output power . 20
5.3.4.1 Test conditions . 20
5.3.4.2 Test method . 20
5.3.5 Transmitter unwanted emissions in the spurious domain . 21
5.3.5.0 Test conditions . 21
5.3.5.1 Pre-scan . 21
5.3.5.2 Identified emissions . 22
5.3.6 Receiver unwanted emissions . 23
5.3.6.0 Test conditions . 23
5.3.6.1 Pre-scan . 23
5.3.6.2 Identified emissions . 23
5.3.7 Receiver Adjacent Channel Rejection . 24
5.3.7.1 Test conditions . 24
5.3.7.2 Test Method . 24
5.3.8 Adaptivity (medium access protocol) . 25
5.3.8.1 Test conditions . 25
5.3.8.2 Test method . 25
5.3.8.3 Generic test procedure for measuring channel/frequency usage . 27
5.3.9 Transmitter unwanted emissions in the out-of-band domain . 28
5.3.9.1 Test conditions . 28
5.3.9.2 Test method . 28
5.3.10 Occupied Channel Bandwidth . 29
5.3.10.1 Test conditions . 29
5.3.10.2 Test method . 29
5.3.11 Receiver sensitivity level . 29
5.3.11.1 Test conditions . 29
5.3.11.2 Test method . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): Maximum Measurement Uncertainty . 33
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 302 567 V2.2.1 (2021-07)
Annex C (normative): Test sites and arrangements for radiated measurements . 34
C.1 Test sites . 34
C.1.1 Open air test sites . 34
C.1.2 Anechoic chamber . 35
C.1.2.1 General . 35
C.1.2.2 Description . 35
C.1.2.3 Influence of parasitic reflections . 35
C.1.2.4 Calibration and mode of use . 35
C.2 Test antenna . 37
C.3 Substitution antenna . 37
Annex D (normative): General description of measurement . 38
D.1 Radiated measurements . 38
D.2 Substitution measurement . 39
Annex E (informative): Bibliography . 40
Annex F (informative): Change History . 41
History . 42

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 302 567 V2.2.1 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.6].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.

National transposition dates
Date of adoption of this EN: 5 July 2021
Date of latest announcement of this EN (doa): 31 October 2021
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2022
Date of withdrawal of any conflicting National Standard (dow): 30 April 2023

ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 302 567 V2.2.1 (2021-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
60 GHz radio equipment are capable of operating at data rates of multiple-gigabit per second.
The spectrum usage conditions for this equipment are set in Commission Decision 2013/752/EU [i.4] and Commission
Decision 2019/1345/EU [i.7] amending Commission Decision 2006/771/EC of 9 November 2006 [i.5] and ERC
Recommendation 70-03 [i.3], annex 3.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 302 567 V2.2.1 (2021-07)
1 Scope
The present document specifies technical characteristics and methods of measurements for radio equipment with
integral antennas operating indoor or outdoor at data rates of multiple-gigabit per second in the 60 GHz frequency
range.
These radio equipment operate with very wideband communications using a variety of directional medium and high
gain antennas to enable a high degree of spectrum reuse, and may use a flexible bandwidth scheme under which they
normally operate in a wideband mode, and periodically reduce their bandwidth (e.g. for antenna training and other
activities).
The technical characteristics of applications using these radio equipment are further described in ETSI TR 102 555 [i.1].
Equipment in this frequency range intended for outdoor Fixed Local Area Network Extension (FLANE) or Fixed
Point-to-Point applications are not in the scope of the present document.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.6] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified
...

Final draft ETSI EN 302 567 V2.2.1 (2021-05)






HARMONISED EUROPEAN STANDARD
Multiple-Gigabit/s radio equipment
operating in the 60 GHz band;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 567 V2.2.1 (2021-05)

Reference
REN/BRAN-230018
Keywords
access, broadband, LAN, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2021.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Spectral power density . 11
4.2.1.0 Applicability. 11
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 12
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Receiver unwanted emissions . 13
4.2.4.0 Applicability. 13
4.2.4.1 Definition . 13
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Requirement . 13
4.2.5.4 Conformance . 14
4.2.6 Short Control Signalling Transmissions . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limits . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver Adjacent Channel Rejection . 14
4.2.7.1 Applicability. 14
4.2.7.2 Definition . 15
4.2.7.3 Performance Criteria . 15
4.2.7.4 Limits . 15
4.2.7.5 Conformance . 15
4.2.8 Transmitter unwanted emissions in the out-of-band domain . 15
4.2.8.0 Applicability. 15
4.2.8.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
4.2.8.2 Limit . 15
4.2.8.3 Conformance . 16
4.2.9 Void . 16
4.2.10 Occupied Channel Bandwidth . 16
4.2.10.1 Applicability. 16
4.2.10.2 Definition . 16
4.2.10.3 Requirements . 16
4.2.10.4 Conformance . 16
4.2.11 Receiver Sensitivity level . 17
4.2.11.1 Applicability. 17
4.2.11.2 Definition . 17
4.2.11.3 Limits . 17
4.2.11.4 Conformance . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 18
5.2 Void . 18
5.3 Test procedure for the essential radio test suites . 18
5.3.0 General . 18
5.3.1 Product Information . 18
5.3.2 Test modulation, frequency and configuration . 18
5.3.3 Spectral power density . 19
5.3.3.1 Test conditions . 19
5.3.3.2 Test method . 19
5.3.4 RF output power . 20
5.3.4.1 Test conditions . 20
5.3.4.2 Test method . 20
5.3.5 Transmitter unwanted emissions in the spurious domain . 21
5.3.5.0 Test conditions . 21
5.3.5.1 Pre-scan . 21
5.3.5.2 Identified emissions . 22
5.3.6 Receiver unwanted emissions . 23
5.3.6.0 Test conditions . 23
5.3.6.1 Pre-scan . 23
5.3.6.2 Identified emissions . 23
5.3.7 Receiver Adjacent Channel Rejection . 24
5.3.7.1 Test conditions . 24
5.3.7.2 Test Method . 24
5.3.8 Adaptivity (medium access protocol) . 25
5.3.8.1 Test conditions . 25
5.3.8.2 Test method . 25
5.3.8.3 Generic test procedure for measuring channel/frequency usage . 27
5.3.9 Transmitter unwanted emissions in the out-of-band domain . 28
5.3.9.1 Test conditions . 28
5.3.9.2 Test method . 28
5.3.10 Occupied Channel Bandwidth . 29
5.3.10.1 Test conditions . 29
5.3.10.2 Test method . 29
5.3.11 Receiver sensitivity level . 29
5.3.11.1 Test conditions . 29
5.3.11.2 Test method . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): Maximum Measurement Uncertainty . 33
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
Annex C (normative): Test sites and arrangements for radiated measurements . 34
C.1 Test sites . 34
C.1.1 Open air test sites . 34
C.1.2 Anechoic chamber . 35
C.1.2.1 General . 35
C.1.2.2 Description . 35
C.1.2.3 Influence of parasitic reflections . 35
C.1.2.4 Calibration and mode of use . 35
C.2 Test antenna . 37
C.3 Substitution antenna . 37
Annex D (normative): General description of measurement . 38
D.1 Radiated measurements . 38
D.2 Substitution measurement . 39
Annex E (informative): Bibliography . 40
Annex F (informative): Change History . 41
History . 42

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband
Radio Access Networks (BRAN), and is now submitted for the Vote phase of the ETSI standards EN Approval
Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.6].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard 6 months after doa
or endorsement of this EN (dop/e):
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
60 GHz radio equipment are capable of operating at data rates of multiple-gigabit per second.
The spectrum usage conditions for this equipment are set in Commission Decision 2013/752/EU [i.4] and Commission
Decision 2019/1345/EU [i.7] amending Commission Decision 2006/771/EC of 9 November 2006 [i.5] and ERC
Recommendation 70-03 [i.3], annex 3.
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 302 567 V2.2.1 (2021-05)
1 Scope
The present document specifies technical characteristics and methods of measurements for radio equipment with
integral antennas operating indoor or outdoor at data rates of multiple-gigabit per second in the 60 GHz frequency
range.
These radio equipment operate with very wideband communications using a variety of directional medium and high
gain antennas to enable a high degree of spectrum reuse, and may use a flexible bandwidth scheme under which they
normally operate in a wideband mode, and periodically reduce their bandwidth (e.g. for antenna training and other
activities).
The technical characteristics of applications using these radio equipment are further described in ETSI TR 102 555 [i.1].
Equipment in this frequency range intended for outdoor Fixed Local Area Network Extension (FLANE) or Fixed
Point-to-Point applications are not in the scope of the present document.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.6] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The
...

Draft ETSI EN 302 567 V2.2.0 (2020-12)






HARMONISED EUROPEAN STANDARD
Multiple-Gigabit/s radio equipment
operating in the 60 GHz band;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 567 V2.2.0 (2020-12)



Reference
REN/BRAN-230018
Keywords
access, broadband, LAN, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 11
4.2.1 Spectral power density . 11
4.2.1.0 Applicability. 11
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Receiver unwanted emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Requirement . 13
4.2.5.4 Conformance . 14
4.2.6 Short Control Signalling Transmissions . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limits . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver Adjacent Channel Rejection . 14
4.2.7.1 Applicability. 14
4.2.7.2 Definition . 14
4.2.7.3 Performance Criteria . 14
4.2.7.4 Limits . 15
4.2.7.5 Conformance . 15
4.2.8 Transmitter unwanted emissions in the out-of-band domain . 15
4.2.8.0 Applicability. 15
4.2.8.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 567 V2.2.0 (2020-12)
4.2.8.2 Limit . 15
4.2.8.3 Conformance . 16
4.2.9 Void . 16
4.2.10 Occupied Channel Bandwidth . 16
4.2.10.1 Applicability. 16
4.2.10.2 Definition . 16
4.2.10.3 Requirements . 16
4.2.10.4 Conformance . 16
4.2.11 Receiver Sensitivity level . 17
4.2.11.1 Applicability. 17
4.2.11.2 Definition . 17
4.2.11.3 Limits . 17
4.2.11.4 Conformance . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 18
5.2 Void . 18
5.3 Test procedure for the essential radio test suites . 18
5.3.0 General . 18
5.3.1 Product Information . 18
5.3.2 Test modulation, frequency and configuration . 18
5.3.3 Spectral power density . 19
5.3.3.1 Test conditions . 19
5.3.3.2 Test method . 19
5.3.4 RF output power . 20
5.3.4.1 Test conditions . 20
5.3.4.2 Test method . 20
5.3.5 Transmitter unwanted emissions . 21
5.3.5.0 Test conditions . 21
5.3.5.1 Pre-scan . 21
5.3.5.2 Identified emissions . 22
5.3.6 Receiver unwanted emissions . 23
5.3.6.0 Test conditions . 23
5.3.6.1 Pre-scan . 23
5.3.6.2 Identified emissions . 23
5.3.7 Receiver Adjacent Channel Rejection . 24
5.3.7.1 Test conditions . 24
5.3.7.2 Test Method . 24
5.3.8 Adaptivity (medium access protocol) . 25
5.3.8.1 Test conditions . 25
5.3.8.2 Test method . 25
5.3.8.3 Generic test procedure for measuring channel/frequency usage . 27
5.3.9 Transmitter unwanted emissions in the out-of-band domain . 28
5.3.9.1 Test conditions . 28
5.3.9.2 Test method . 28
5.3.10 Occupied Channel Bandwidth . 29
5.3.10.1 Test conditions . 29
5.3.10.2 Test method . 29
5.3.11 Receiver sensitivity level . 29
5.3.11.1 Test conditions . 29
5.3.11.2 Test method . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): Maximum Measurement Uncertainty . 33
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Annex C (normative): Test sites and arrangements for radiated measurements . 34
C.1 Test sites . 34
C.1.1 Open air test sites . 34
C.1.2 Anechoic chamber . 35
C.1.2.1 General . 35
C.1.2.2 Description . 35
C.1.2.3 Influence of parasitic reflections . 35
C.1.2.4 Calibration and mode of use . 35
C.2 Test antenna . 37
C.3 Substitution antenna . 37
Annex D (normative): General description of measurement . 38
D.1 Radiated measurements . 38
D.2 Substitution measurement . 39
Annex E (informative): Bibliography . 40
Annex F (informative): Change History . 41
History . 42

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.6].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard 6 months after doa
or endorsement of this EN (dop/e):
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Introduction
60 GHz radio equipment are capable of operating at data rates of multiple-gigabit per second.
The spectrum usage conditions for this equipment are set in Commission Decision 2013/752/EU [i.4] and Commission
Decision 2019/1345/EU [i.7] amending Commission Decision 2006/771/EC of 9 November 2006 [i.5] and ERC
Recommendation 70-03 [i.3], annex 3.
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 567 V2.2.0 (2020-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for radio equipment with
integral antennas operating indoor or outdoor at data rates of multiple-gigabit per second in the 60 GHz frequency
range.
These radio equipment operate with very wideband communications using a variety of directional medium and high
gain antennas to enable a high degree of spectrum reuse, and may use a flexible bandwidth scheme under which they
normally operate in a wideband mode, and periodically reduce their bandwidth (e.g. for antenna training and other
activities).
The technical characteristics of applications using these radio equipment are further described in ETSI TR 102 555 [i.1].
Equipment in this frequency range intended for outdoor Fixed Local Area Network Extension (FLANE) or Fixed
Point-to-Point applications are not in the scope of the present document.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.6] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 302 567 V2.2.0 (2020-12)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 102 555: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical
characteristics of multiple gigabit wireless systems in the 60 GHz range System Reference
Document".
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisat
...

SLOVENSKI STANDARD
oSIST prEN 302 567 V2.2.0:2021
01-februar-2021
Večgigabitna radijska oprema, ki deluje v pasu 60 GHz - Harmonizirani standard za
dostop do radijskega spektra
Multiple-Gigabit/s radio equipment operating in the 60 GHz band - Harmonised Standard
for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 302 567 V2.2.0 (2020-12)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
35.110 Omreževanje Networking
oSIST prEN 302 567 V2.2.0:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 302 567 V2.2.0:2021

---------------------- Page: 2 ----------------------
oSIST prEN 302 567 V2.2.0:2021
Draft ETSI EN 302 567 V2.2.0 (2020-12)






HARMONISED EUROPEAN STANDARD
Multiple-Gigabit/s radio equipment
operating in the 60 GHz band;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 2 Draft ETSI EN 302 567 V2.2.0 (2020-12)



Reference
REN/BRAN-230018
Keywords
access, broadband, LAN, radio, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 3 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 11
4.2.1 Spectral power density . 11
4.2.1.0 Applicability. 11
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Receiver unwanted emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Requirement . 13
4.2.5.4 Conformance . 14
4.2.6 Short Control Signalling Transmissions . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limits . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver Adjacent Channel Rejection . 14
4.2.7.1 Applicability. 14
4.2.7.2 Definition . 14
4.2.7.3 Performance Criteria . 14
4.2.7.4 Limits . 15
4.2.7.5 Conformance . 15
4.2.8 Transmitter unwanted emissions in the out-of-band domain . 15
4.2.8.0 Applicability. 15
4.2.8.1 Definition . 15
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 4 Draft ETSI EN 302 567 V2.2.0 (2020-12)
4.2.8.2 Limit . 15
4.2.8.3 Conformance . 16
4.2.9 Void . 16
4.2.10 Occupied Channel Bandwidth . 16
4.2.10.1 Applicability. 16
4.2.10.2 Definition . 16
4.2.10.3 Requirements . 16
4.2.10.4 Conformance . 16
4.2.11 Receiver Sensitivity level . 17
4.2.11.1 Applicability. 17
4.2.11.2 Definition . 17
4.2.11.3 Limits . 17
4.2.11.4 Conformance . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 18
5.2 Void . 18
5.3 Test procedure for the essential radio test suites . 18
5.3.0 General . 18
5.3.1 Product Information . 18
5.3.2 Test modulation, frequency and configuration . 18
5.3.3 Spectral power density . 19
5.3.3.1 Test conditions . 19
5.3.3.2 Test method . 19
5.3.4 RF output power . 20
5.3.4.1 Test conditions . 20
5.3.4.2 Test method . 20
5.3.5 Transmitter unwanted emissions . 21
5.3.5.0 Test conditions . 21
5.3.5.1 Pre-scan . 21
5.3.5.2 Identified emissions . 22
5.3.6 Receiver unwanted emissions . 23
5.3.6.0 Test conditions . 23
5.3.6.1 Pre-scan . 23
5.3.6.2 Identified emissions . 23
5.3.7 Receiver Adjacent Channel Rejection . 24
5.3.7.1 Test conditions . 24
5.3.7.2 Test Method . 24
5.3.8 Adaptivity (medium access protocol) . 25
5.3.8.1 Test conditions . 25
5.3.8.2 Test method . 25
5.3.8.3 Generic test procedure for measuring channel/frequency usage . 27
5.3.9 Transmitter unwanted emissions in the out-of-band domain . 28
5.3.9.1 Test conditions . 28
5.3.9.2 Test method . 28
5.3.10 Occupied Channel Bandwidth . 29
5.3.10.1 Test conditions . 29
5.3.10.2 Test method . 29
5.3.11 Receiver sensitivity level . 29
5.3.11.1 Test conditions . 29
5.3.11.2 Test method . 29
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 31
Annex B (informative): Maximum Measurement Uncertainty . 33
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 5 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Annex C (normative): Test sites and arrangements for radiated measurements . 34
C.1 Test sites . 34
C.1.1 Open air test sites . 34
C.1.2 Anechoic chamber . 35
C.1.2.1 General . 35
C.1.2.2 Description . 35
C.1.2.3 Influence of parasitic reflections . 35
C.1.2.4 Calibration and mode of use . 35
C.2 Test antenna . 37
C.3 Substitution antenna . 37
Annex D (normative): General description of measurement . 38
D.1 Radiated measurements . 38
D.2 Substitution measurement . 39
Annex E (informative): Bibliography . 40
Annex F (informative): Change History . 41
History . 42

ETSI

---------------------- Page: 7 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 6 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.6].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard 6 months after doa
or endorsement of this EN (dop/e):
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 8 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 7 Draft ETSI EN 302 567 V2.2.0 (2020-12)
Introduction
60 GHz radio equipment are capable of operating at data rates of multiple-gigabit per second.
The spectrum usage conditions for this equipment are set in Commission Decision 2013/752/EU [i.4] and Commission
Decision 2019/1345/EU [i.7] amending Commission Decision 2006/771/EC of 9 November 2006 [i.5] and ERC
Recommendation 70-03 [i.3], annex 3.
ETSI

---------------------- Page: 9 ----------------------
oSIST prEN 302 567 V2.2.0:2021
 8 Draft ETSI EN 302 567 V2.2.0 (2020-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for radio equipment with
integral antennas operating indoor or outdoor at data rates of multiple-gigabit per second in the 60 GHz frequency
range.
These radio equipment operate with very wideband communications using a variety of directional medium and high
gain antennas to enable a high degree of spectrum reuse, and may use a flexible bandwidth scheme under which they
normally operate in a wideband mode, and periodically reduce their bandwidth (e.g. for antenna training and other
activities).
The technical characteristics of applications using these radio equipment are further described in ETSI TR 102 555 [i.1].
Equipment in this frequency range intended for outdoor Fixed Local Area Network Extension (FLANE) or Fixed
Point-to-Point applications are not in the scope of the present document.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz

NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.6] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicabl
...