ETSI EN 301 908-20 V6.3.1 (2016-05)
IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD WMAN (Mobile WiMAXTM) TDD Base Stations (BS)
IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD WMAN (Mobile WiMAXTM) TDD Base Stations (BS)
REN/MSG-TFES-11-20-RED
Celična omrežja IMT - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU - 20. del: Bazne postaje TDD OFDMA TDD WMAN (mobilni WiMAXTM)
Ta dokument se uporablja za radijsko opremo naslednje vrste:
• bazne postaje za IMT-2000 OFDMA TDD WMAN (mobilni WiMAXTM), ki delujejo v načinu TDD
Zahteve v tem dokumentu veljajo za bazne postaje širokega območja in lokalne bazne postaje, razen če ni navedeno drugače.
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja in tudi podpira učinkovito uporabo radijskega spektra, tako da ne pride do škodljivih motenj.
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive o radijski opremi 2014/53/EU [i.2].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.:L0$;70IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 20: OFDMA TDD WMAN (Mobile WiMAXTM) TDD Base Stations (BS)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 301 908-20 V6.3.1 (2016-05)SIST EN 301 908-20 V6.3.1:2016en01-julij-2016SIST EN 301 908-20 V6.3.1:2016SLOVENSKI
STANDARD
SIST EN 301 908-20 V6.3.1:2016
ETSI EN 301 908-20 V6.3.1 (2016-05) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 20: OFDMA TDD WMAN (Mobile WiMAXTM) TDD Base Stations (BS)
HARMONISED EUROPEAN STANDARD SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)2
Reference REN/MSG-TFES-11-20-RED Keywords broadband, IMT, IMT-2000, mobile, OFDMA, radio, regulation, TDD, WiMAX, WMAN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 9 3.3 Abbreviations . 9 4 Technical requirements specification . 10 4.1 Environmental profile . 10 4.2 Conformance requirements . 10 4.2.1 Introduction. 10 4.2.2 Transmitter Spectrum Emission Mask . 11 4.2.2.1 Definition . 11 4.2.2.2 Limits . 11 4.2.2.2.1 Spectrum emission mask for 5 MHz channel bandwidth - BCI 1.B and 3.A . 11 4.2.2.2.2 Spectrum emission mask for 10 MHz channel bandwidth - BCI 1.B and 3.A . 11 4.2.2.2.3 Spectrum emission mask for BCI 5L.A, 5L.C, 5H.A and 5H.C . 11 4.2.2.3 Conformance . 12 4.2.3 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 12 4.2.3.1 Definition . 12 4.2.3.2 Limits . 12 4.2.3.2.1 ACLR requirements for 5 MHz channel bandwidth . 12 4.2.3.2.2 ACLR requirements for 10 MHz channel bandwidth . 13 4.2.3.3 Conformance . 13 4.2.4 Transmitter spurious emissions . 13 4.2.4.1 Definition . 13 4.2.4.2 Limits . 13 4.2.4.2.1 General requirements . 13 4.2.4.2.2 Additional Spurious Emission Requirements . 14 4.2.4.3 Conformance . 14 4.2.5 Base station maximum output power . 15 4.2.5.1 Definition . 15 4.2.5.2 Limits . 15 4.2.5.3 Conformance . 15 4.2.6 Transmit intermodulation . 15 4.2.6.1 Definition . 15 4.2.6.2 Limits . 15 4.2.6.3 Conformance . 15 4.2.7 Receiver spurious emissions . 15 4.2.7.1 Definition . 15 4.2.7.2 Limits . 16 4.2.7.3 Conformance . 16 4.2.8 Receiver blocking characteristics . 16 4.2.8.1 Definition . 16 4.2.8.2 Limits . 16 4.2.8.3 Conformance . 18 4.2.9 Receiver intermodulation characteristics . 18 4.2.9.1 Definition . 18 4.2.9.2 Limits . 18 SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)4 4.2.9.3 Conformance . 19 4.2.10 Receiver Adjacent Channel Selectivity. 19 4.2.10.1 Definition . 19 4.2.10.2 Limits . 19 4.2.10.3 Conformance . 19 4.2.11 Receiver reference sensitivity level . 19 4.2.11.1 Definition . 19 4.2.11.2 Limits . 20 4.2.11.3 Conformance . 20 5 Testing for compliance with technical requirements . 20 5.1 Environmental conditions for testing . 20 5.2 Product information . 20 5.3 Interpretation of the measurement results . 20 5.4 Essential radio test suites . 21 5.4.1 Transmitter Spectrum Emission Mask . 21 5.4.1.1 Method of measurement . 22 5.4.1.1.1 Initial conditions . 22 5.4.1.1.2 Procedure . 22 5.4.1.2 Test requirements . 23 5.4.2 Transmitter Adjacent Channel Leakage Power Ratio (ACLR) . 23 5.4.2.1 Method of measurement . 23 5.4.2.1.1 Initial conditions . 23 5.4.2.1.2 Procedure . 23 5.4.2.2 Test requirements . 24 5.4.3 Transmitter spurious emissions . 24 5.4.3.1 Method of measurement . 24 5.4.3.1.1 Initial conditions . 25 5.4.3.1.2 Procedure . 25 5.4.3.2 Test requirements . 25 5.4.4 Base Station maximum output power . 25 5.4.4.1 Method of measurement . 25 5.4.4.1.1 Initial conditions . 26 5.4.4.1.2 Procedure . 26 5.4.4.2 Test requirements . 26 5.4.5 Transmit Intermodulation . 26 5.4.5.1 Method of measurement . 26 5.4.5.1.1 Initial conditions . 27 5.4.5.1.2 Procedure . 27 5.4.5.2 Test requirements . 27 5.4.6 Receiver spurious emissions . 27 5.4.6.1 Method of measurement . 28 5.4.6.1.1 Initial conditions . 28 5.4.6.1.2 Procedure . 28 5.4.6.2 Test requirements . 28 5.4.7 Receiver blocking characteristics . 28 5.4.7.1 Method of Measurement . 28 5.4.7.1.1 Initial conditions . 29 5.4.7.1.2 Procedure . 29 5.4.7.2 Test requirements . 30 5.4.8 Receiver Intermodulation characteristics . 30 5.4.8.1 Method of measurement . 30 5.4.8.1.1 Initial conditions . 30 5.4.8.1.2 Procedure . 31 5.4.8.2 Test requirements . 31 5.4.9 Receiver adjacent channel selectivity . 31 5.4.9.1 Method of measurement . 31 5.4.9.1.1 Initial conditions . 32 5.4.9.1.2 Procedure . 32 5.4.9.2 Test requirements . 32 5.4.10 Receiver reference sensitivity level . 32 5.4.10.1 Method of test . 32 SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)5 5.4.10.2 Test requirement . 32 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 33 Annex B (normative): Environmental profile . 34 Annex C (informative): Void . 35 Annex D (informative): Bibliography . 36 History . 37
SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.2]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 20 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.9].
National transposition dates Date of adoption of this EN: 20 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 January 2017 Date of withdrawal of any conflicting National Standard (dow): 31 January 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover radio equipment within the scope of the Radio Equipment Directive 2014/53/EU [i.2]. The present document is produced following the guidance in ETSI EG 203 336 [i.3] as applicable.
SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)7 1 Scope The present document applies to the following radio equipment type: • Base stations for IMT-2000 OFDMA TDD WMAN (Mobile WiMAXTM) operating in TDD mode. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: OFDMA TDD WMAN Base Station frequency bands Mobile WiMAXTM Band Class Index IMT-2000 OFDMA TDD WMAN service operating bands Channel Bandwidth; BW 1.B 2 300 MHz to 2 400 MHz 5 MHz and 10 MHz
3.A 2 500 MHz to 2 690 MHz 5 MHz and 10 MHz 5L.A 3 400 MHz to 3 600 MHz 5 MHz 5L.C 3 400 MHz to 3 600 MHz 10 MHz 5H.A 3 600 MHz to 3 800 MHz 5 MHz 5H.C 3 600 MHz to 3 800 MHz 10 MHz
The requirements in the present document apply to both Wide Area Base Stations and Local Area Base Stations unless otherwise stated.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive 2014/53/EU [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] WMF-T25-002-R010v06 (2012): "WiMAX Forum® Test Procedures - Mobile Radio Conformance Tests" - Release 1 v0.6. [2] CEPT/ERC/Recommendation 74-01E (Siófok 98, Nice 99, Sesimbra 02, Hradec Kralove 05, Cardiff 11) (01-2011): "Unwanted emissions in the spurious domain". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. SIST EN 301 908-20 V6.3.1:2016
ETSI ETSI EN 301 908-20 V6.3.1 (2016-05)8 The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain". [i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.3] ETSI EG 203 336 (V1.1.1) (2015): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU". [i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagnetic fields above 1 GHz". [i.5] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.7] Void. [i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. [i.9] ETSI EN 301 908-1 (V11.1.1): "IMT cellular
...
ETSI EN 301 908-20 V6.3.1 (2016-05)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
TM
Part 20: OFDMA TDD WMAN (Mobile WiMAX )
TDD Base Stations (BS)
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-20 V6.3.1 (2016-05)
Reference
REN/MSG-TFES-11-20-RED
Keywords
broadband, IMT, IMT-2000, mobile, OFDMA,
radio, regulation, TDD, WiMAX, WMAN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-20 V6.3.1 (2016-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specification . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Transmitter Spectrum Emission Mask . 11
4.2.2.1 Definition . 11
4.2.2.2 Limits . 11
4.2.2.2.1 Spectrum emission mask for 5 MHz channel bandwidth - BCI 1.B and 3.A . 11
4.2.2.2.2 Spectrum emission mask for 10 MHz channel bandwidth - BCI 1.B and 3.A . 11
4.2.2.2.3 Spectrum emission mask for BCI 5L.A, 5L.C, 5H.A and 5H.C . 11
4.2.2.3 Conformance . 12
4.2.3 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 12
4.2.3.1 Definition . 12
4.2.3.2 Limits . 12
4.2.3.2.1 ACLR requirements for 5 MHz channel bandwidth . 12
4.2.3.2.2 ACLR requirements for 10 MHz channel bandwidth . 13
4.2.3.3 Conformance . 13
4.2.4 Transmitter spurious emis sions . 13
4.2.4.1 Definition . 13
4.2.4.2 Limits . 13
4.2.4.2.1 General requirements . 13
4.2.4.2.2 Additional Spurious Emission Requirements . 14
4.2.4.3 Conformance . 14
4.2.5 Base station maximum output power . 15
4.2.5.1 Definition . 15
4.2.5.2 Limits . 15
4.2.5.3 Conformance . 15
4.2.6 Transmit intermodulation . 15
4.2.6.1 Definition . 15
4.2.6.2 Limits . 15
4.2.6.3 Conformance . 15
4.2.7 Receiver spurious emissions . 15
4.2.7.1 Definition . 15
4.2.7.2 Limits . 16
4.2.7.3 Conformance . 16
4.2.8 Receiver blocking characteristics . 16
4.2.8.1 Definition . 16
4.2.8.2 Limits . 16
4.2.8.3 Conformance . 18
4.2.9 Receiver intermodulation characteristics . 18
4.2.9.1 Definition . 18
4.2.9.2 Limits . 18
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-20 V6.3.1 (2016-05)
4.2.9.3 Conformance . 19
4.2.10 Receiver Adjacent Channel Selectivity. 19
4.2.10.1 Definition . 19
4.2.10.2 Limits . 19
4.2.10.3 Conformance . 19
4.2.11 Receiver reference sensitivity level . 19
4.2.11.1 Definition . 19
4.2.11.2 Limits . 20
4.2.11.3 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Product information . 20
5.3 Interpretation of the measurement results . 20
5.4 Essential radio test suites . 21
5.4.1 Transmitter Spectrum Emission Mask . 21
5.4.1.1 Method of measurement . 22
5.4.1.1.1 Initial conditions . 22
5.4.1.1.2 Procedure . 22
5.4.1.2 Test requirements . 23
5.4.2 Transmitter Adjacent Channel Leakage Power Ratio (ACLR) . 23
5.4.2.1 Method of measurement . 23
5.4.2.1.1 Initial conditions . 23
5.4.2.1.2 Procedure . 23
5.4.2.2 Test requirements . 24
5.4.3 Transmitter spurious emis sions . 24
5.4.3.1 Method of measurement . 24
5.4.3.1.1 Initial conditions . 25
5.4.3.1.2 Procedure . 25
5.4.3.2 Test requirements . 25
5.4.4 Base Station maximum output power . 25
5.4.4.1 Method of measurement . 25
5.4.4.1.1 Initial conditions . 26
5.4.4.1.2 Procedure . 26
5.4.4.2 Test requirements . 26
5.4.5 Transmit Intermodulation . 26
5.4.5.1 Method of measurement . 26
5.4.5.1.1 Initial conditions . 27
5.4.5.1.2 Procedure . 27
5.4.5.2 Test requirements . 27
5.4.6 Receiver spurious emissions . 27
5.4.6.1 Method of measurement . 28
5.4.6.1.1 Initial conditions . 28
5.4.6.1.2 Procedure . 28
5.4.6.2 Test requirements . 28
5.4.7 Receiver blocking characteristics . 28
5.4.7.1 Method of Measurement . 28
5.4.7.1.1 Initial conditions . 29
5.4.7.1.2 Procedure . 29
5.4.7.2 Test requirements . 30
5.4.8 Receiver Intermodulation characteristics . 30
5.4.8.1 Method of measurement . 30
5.4.8.1.1 Initial conditions . 30
5.4.8.1.2 Procedure . 31
5.4.8.2 Test requirements . 31
5.4.9 Receiver adjacent channel selectivity . 31
5.4.9.1 Method of measurement . 31
5.4.9.1.1 Initial conditions . 32
5.4.9.1.2 Procedure . 32
5.4.9.2 Test requirements . 32
5.4.10 Receiver reference sensitivity level . 32
5.4.10.1 Method of test . 32
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-20 V6.3.1 (2016-05)
5.4.10.2 Test requirement . 32
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 33
Annex B (normative): Environmental profile . 34
Annex C (informative): Void . 35
Annex D (informative): Bibliography . 36
History . 37
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-20 V6.3.1 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.8] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 20 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.9].
National transposition dates
Date of adoption of this EN: 20 April 2016
Date of latest announcement of this EN (doa): 31 July 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2017
Date of withdrawal of any conflicting National Standard (dow): 31 January 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to
cover radio equipment within the scope of the Radio Equipment Directive 2014/53/EU [i.2]. The present document is
produced following the guidance in ETSI EG 203 336 [i.3] as applicable.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-20 V6.3.1 (2016-05)
1 Scope
The present document applies to the following radio equipment type:
TM
• Base stations for IMT-2000 OFDMA TDD WMAN (Mobile WiMAX ) operating in TDD mode.
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: OFDMA TDD WMAN Base Station frequency bands
TM
Mobile WiMAX Band IMT-2000 OFDMA TDD WMAN Channel Bandwidth; BW
Class Index service operating bands
1.B 2 300 MHz to 2 400 MHz 5 MHz and 10 MHz
3.A 2 500 MHz to 2 690 MHz 5 MHz and 10 MHz
5L.A 3 400 MHz to 3 600 MHz 5 MHz
5L.C 3 400 MHz to 3 600 MHz 10 MHz
5H.A 3 600 MHz to 3 800 MHz 5 MHz
5H.C 3 600 MHz to 3 800 MHz 10 MHz
The requirements in the present document apply to both Wide Area Base Stations and Local Area Base Stations unless
otherwise stated.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive 2014/53/EU [i.2] may apply to equipment within the
scope of the present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] WMF-T25-002-R010v06 (2012): "WiMAX Forum® Test Procedures - Mobile Radio
Conformance Tests" - Release 1 v0.6.
[2] CEPT/ERC/Recommendation 74-01E (Siófok 98, Nice 99, Sesimbra 02, Hradec Kralove 05,
Cardiff 11) (01-2011): "Unwanted emissions in the spurious domain".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-20 V6.3.1 (2016-05)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain".
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] ETSI EG 203 336 (V1.1.1) (2015): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Guide for the selection of technical parameters for the production of Harmonised
Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".
[i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.5] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.7] Void.
[i.8] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.9] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the
essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and
common requirement
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.