ETSI EG 201 693 V1.1.2 (1999-07)

Integrated Services Digital Network (ISDN); Signalling System No.7; Master list of codepoints

DEG/SPS-01065

Digitalno omrežje z integriranimi storitvami (ISDN) – Signalizacija št. 7 – Glavni seznam kodirnih točk

General Information

• Status: Published
• Publication Date: 07-Oct-1999
• Technical Committee: SPS 1 - Network Signalling
• Current Stage: 12 - Completion
• Due Date: 08-Oct-1999
• Completion Date: 08-Oct-1999
• Ref Project: SIST-V ETSI/EG 201 693 V1.1.3:2005 - Integrated Services Digital Network (ISDN); Signalling System No.7; Master list of codepoints

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-V ETSI/EG 201 693 V1.1.3:2005
01-januar-2005
'LJLWDOQRRPUHåMH]LQWHJULUDQLPLVWRULWYDPL,6'1±6LJQDOL]DFLMDãW±*ODYQL
VH]QDPNRGLUQLKWRþN
Integrated Services Digital Network (ISDN); Signalling System No.7; Master list of
codepoints
Ta slovenski standard je istoveten z: EG 201 693 Version 1.1.3
ICS:
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
SIST-V ETSI/EG 201 693 V1.1.3:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005

---------------------- Page: 2 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
ETSI EG 201 693 V1.1.3 (1999-10)
ETSI Guide
Integrated Services Digital Network (ISDN);
Signalling System No.7;
Master list of codepoints

---------------------- Page: 3 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
2 ETSI EG 201 693 V1.1.3 (1999-10)
Reference
DEG/SPS-01065 (foc00ie2.PDF)
Keywords
SS7, protocol, SCCP, MTP, interworking
ETSI
Postal address
F-06921 Sophia Antipolis Cedex - FRANCE
Office address
650 Route des Lucioles - Sophia Antipolis
Valbonne - FRANCE
Tel.: [phone]  Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Internet
[e-mail]
Individual copies of this ETSI deliverable
can be downloaded from
http://www.etsi.org
If you find errors in the present document, send your
comment to: [e-mail]
Important notice
This ETSI deliverable may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference should be the printing on ETSI printers of the PDF version kept on a specific network
drive within ETSI Secretariat.
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1999.
All rights reserved.
ETSI

---------------------- Page: 4 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
3 ETSI EG 201 693 V1.1.3 (1999-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Introduction. 4
1 Scope. 5
2 References. 5
3 Definitions and abbreviations. 6
3.1 Definitions . 6
3.2 Abbreviations. 6
4 SCCP address code allocations. 7
4.1 SSN. 7
4.2 Translation type . 8
4.3 Numbering Plan . 8
4.4 Encoding scheme . 9
4.5 Nature of Address Indicator. 9
5 MTP code allocations . 10
5.1 MTP SI code allocations (for NI=00 (international network) only). 10
5.2 MTP User Part Identity code allocations . 11
Annex A (informative): Network interconnections. 12
A.1 SCCP. 12
A.1.1 Introduction of SCCP to post-Blue-Book . 12
A.1.2 SCCP Return message on error procedure. 12
A.1.2.1 Use of the return option. 13
A.1.2.1.1 Incomplete routeing. 14
A.1.2.1.2 Replicated subsystems . 14
A.1.2.1.3 Changes to calling and called party addresses . 14
A.1.2.1.4 Scope of calling party address . 14
A.1.2.1.5 Calling party addresses in UDTS messages. 14
A.1.2.1.6 Conversion of called party address. 14
A.1.2.1.7 SCCP corrective action for messages returned on error . 15
A.1.3 Checking for called addresses in own node or network . 15
A.1.4 Checking for circular routeing of messages . 15
A.2 MTP . 15
A.2.1 Point Code Allocation. 15
A.2.2 Repetition of Signal Units. 15
A.2.3 Error Correction Procedure. 15
A.2.4 Routeing of Messages . 15
A.2.5 Signalling Point Restart . 16
A.2.6 Management messages. 16
A.2.7 MTP Screening . 16
A.2.8 Transfer Prohibited Procedures . 16
Bibliography. 17
History. 18
ETSI

---------------------- Page: 5 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
4 ETSI EG 201 693 V1.1.3 (1999-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect
of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server
(http://www.etsi.org/ipr).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server)
which are, or may be, or may become, essential to the present document.
Foreword
This ETSI Guide (EG) has been produced by ETSI Technical Committee Services and Protocols for Advanced
Networks (SPAN).
Introduction
The tables are intended to record all known assigned addressing codes. Where a particular ETSI member is shown to
have assigned a code or codes this should not be taken to mean that the codes are unavailable for standardization, but to
allow a reasoned choice to be made before assigning codes for new services. In future all newly assigned codes will be
recorded in the present document rather than the relevant ETSI MTP and SCCP specifications. Thus if referenced by
these specifications then the information shall be considered normative.
Some of the SCCP material in the present document is based on ITU-T Recommendation Q.715 [1] which is a very
valuable source of additional information and should be considered as a complement to the present document.
ETSI

---------------------- Page: 6 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
5 ETSI EG 201 693 V1.1.3 (1999-10)
1 Scope
The present document is intended for use by designers of MTP/SCCP applications as well as by network operators
configuring those applications to help facilitate MTP/SCCP interconnect between ETSI member networks.
In addition to information of an advisory nature, all known standardized SCCP message address codes and MTP SI
codes are also listed.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, subsequent revisions do apply.
• A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same
number.
[1] ITU-T Recommendation Q.715: "Signalling connection control part user guide".
[2] ITU-T Recommendation Q.713: "Signalling Connection Control Part formats and codes".
[3] ETSI GSM 03.03: "Digital cellular telecommunications system (Phase 2+); Numbering, addressing
and identification (GSM 03.03)".
[4] ETSI GSM 08.06: "Digital cellular telecommunications system (Phase 2+); Signalling transport
mechanism specification for the Base Station System - Mobile-services Switching Centre (BSS -
MSC) interface (GSM 08.06 version 5.3.0 Release 1996)".
[5] ETSI GSM 03.66: "Digital cellular telecommunications system (Phase 2+); Support of Mobile
Number Portability (MNP); Stage 2 (GSM 03.66 version 7.1.0 Release 1998)".
[6] ITU-T Recommendation Q.704: "Signalling network functions and messages".
[7] ITU-T Recommendation Q.701: "Functional description of the message transfer part (MTP) of
Signalling System No. 7".
[8] ITU-T Recommendation Q.703: "Signalling link".
[9] ITU-T Recommendation Q.2210: "Message transfer part level 3 functions and messages using the
services of ITU-T Recommendation Q.2140".
[10] ITU-T Recommendation E.210: "Ship station identification for VHF/UHF and maritime mobile-
satellite services".
[11] ITU-T Recommendation E.211: "Selection procedures for VHF/UHF maritime mobile services".
[12] ITU-T Recommendation E.212: "The international identification plan for mobile terminals and
mobile users".
[13] ITU-T Recommendation E.214: "Structure of the land mobile global title for the signalling
connection control part (SCCP)".
[14] ITU-T Recommendation E.733: "Methods for dimensioning resources in Signalling System No. 7
networks".
ETSI

---------------------- Page: 7 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
6 ETSI EG 201 693 V1.1.3 (1999-10)
[15] ITU-T Recommendation F.69: "The international telex service – Service and operational
provisions of telex destination codes and telex network identification codes".
[16] ITU-T Recommendation E.164: "The international public telecommunication numbering plan".
[17] ITU-T Recommendation X.121: "International numbering plan for public data networks".
3 Definitions and abbreviations
3.1 Definitions
The definitions of the MTP/SCCP recommendations referenced in clause 2 apply.
3.2 Abbreviations
DPC Destination Point Code
GT Global Ttitle
MTP Message Transfer Part
RI Routing Indicator
SCCP Signalling Connection Control Part
SI Service Indicator
SSN Sub System Number
TC Transaction Capability
UDTS Unit Data Service
UHF Ultra-High Frequency
VHF Very High Frequency
ETSI

---------------------- Page: 8 ----------------------

SIST-V ETSI/EG 201 693 V1.1.3:2005
7 ETSI EG 201 693 V1.1.3 (1999-10)
4 SCCP address code allocations
In general the rules of ITU-T Recommendation Q.713 [2] should apply to ensure ease of interworking SCCP between
both ETSI and non-ETSI-member networks. Addressing codes not standardized within ITU-T may be exchanged
subject to agreement of all concerned operators. Address codes for the support of services not standardized in ITU-T but
agreed within ETSI are recorded in the present document in a similar way to ITU-T Recommendation Q.713 [2],
annex B, where appropriate.
4.1 SSN
Table 1
Decimal Bits Meaning Assignment
Value 8 7 6 5 4 3 2 1

0 0 0 0 0 0 0 0 0 SSN not known/not used ITU-T
1 0 0 0 0 0 0 0 1 SCCP management ITU-T
2 0 0 0 0 0 0 1 0 reserved for ITU-T-T allocation ITU-T
3 0 0 0 0 0 0 1 1 ISDN user part ITU-T
4 0 0 0 0 0 1 0 0 OMAP ITU-T
5 0 0 0 0 0 1 0 1 MAP (mobile application part) ITU-T
6 0 0 0 0 0 1 1 0 HLR (home location register) ITU-T
7 0 0 0 0 0 1 1 1 VLR (visitor location register) ITU-T
8 0 0 0 0 1 0 0 0 MSC (mobile switching centre) ITU-T

9 0 0 0 0 1 0 0 1 EIC (equipment identifier centre) ITU-T
10 0 0 0 0 1 0 1 0 AUC (authentication centre) ITU-T
11 0 0 0 0 1 0 1 1 ISDN supplementary services ITU-T
12 0 0 0 0 1 1 0 0 INAP ETSI
13 0 0 0 0 1 1 0 1 broadband ISDN edge-to-edge ITU-T
14 0 0 0 0 1 1 1 0 TC test responder ITU-T
15 0 0 0 0 1 1 1 1

to ITU-T
  Reserved for international use
31 0 0 0 1 1 1 1 1

32 0 0 1 0 0 0 0 0 

to
 
147 1 0 0 1 0 0 1 1
 Reserved for ETSI allocation GSM ETSI GSM 03.03 [3]
148 1 0 0 1 0 1 0 0
                          GSM ETSI GSM 03.03 [3]
149 1 0 0 1 0 1 0 1
Œ                          GSM ETSI GSM 03.03 [3]
150 1 0 0 1 0 1 1 0
                        GSM ETSI GSM 03.03 [3]
151 1 0 0 1 0 1 1 1 

to  Reserved for national network use
  ETSI
252 1 1 1 1 1 1 0 0 

253 1 1 1 1 1 1 0 1 O&M(BSS)
ETSI GSM 08.06 [4]
254
...