Environmental Engineering (EE); Power supply interface at the input of Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current (DC)

REN/EE-0270

Okoljski inženiring (EE) - Napajalni vmesnik na vhodu informacijske in komunikacijske tehnologije (IKT) - 2. del: Enosmerna napetost - 48 V (DC)

Ta dokument vsebuje zahteve in meritvene metode za fizični vmesnik »A«, ki je med napajalnim sistemom/sistemi ter informacijsko in komunikacijsko tehnološko opremo (ICT), ki porablja električno energijo.
Nazivna napetost pri električnem vmesniku »A« informacijske in komunikacijske tehnološke opreme, določena v tem dokumentu, je enosmerna napetost – 48 V.
Enosmerno napajanje lahko poteka prek električnega sistema z enosmernim tokom (npr. temelječega na usmernikih na izmenični tok na mreži ali enosmernih pretvornikih v solarnem sistemu, gorivni celici, motorju na izmenični tok ali generatorju gorivne celice), poleg tega pa je na voljo tudi neposredno napajanje z baterijskim pomožnim sistemom v tem sistemu napajanja z enosmernim tokom. Namen tega dokumenta je uporaba napajalnega sistema z enakimi značilnostmi za vso informacijsko in komunikacijsko tehnološko opremo, ki je določena za področje uporabe, za:
– omogočanje medsebojnega delovanja različnih vrst napajalnih enot;
– omogočanje standardizacije informacijske in komunikacijske tehnološke opreme;
– omogočanje nameščanja, delovanja in vzdrževanja informacijske in komunikacijske tehnološke opreme ter sistemov različnega izvora v istem omrežju.
Cilj tega dokumenta je zagotavljanje električne združljivosti med napajalno opremo ter informacijsko in komunikacijsko tehnološko opremo, ki porablja električno energijo, med različnimi sistemskimi bloki in obremenitvami, povezanimi z istim virom napajanja, ki napaja vmesnik »A« (npr. enota za nadzor/spremljanje, hladilni sistem itd.).
Zahteve so določene za:
– napajalni vhod vseh vrst informacijske in komunikacijske tehnološke opreme, nameščene v telekomunikacijskih središčih in povezane z vmesnikom »A«, ki se napaja z enosmerno napetostjo;
– vse vrste informacijske in komunikacijske tehnološke opreme, nameščene v omrežjih za dostop in prostorih strank, pri katerih vmesnik »A« z enosmerno napetostjo prav tako uporablja oprema, ki zahteva napajanje z enosmernim tokom;
– vse vrste informacijske in komunikacijske tehnološke opreme z enosmerno napetostjo, ki se uporablja v stacionarnih in mobilnih omrežjih, nameščenih na različnih
lokacijah, kot so stavbe, pokriti prostori, cestne omarice.
Motnje v napajalnem vmesniku »A«, povezane s pojavom trajnega vala pod 20 kHz, so opisane v tem dokumentu.
Ta dokument ne opisuje varnostnih zahtev; opisane so v ustreznih varnostnih standardih.
Ta dokument ne opisuje zahtev za elektromagnetno združljivost; opisane so v ustreznih standardih za elektromagnetno združljivost.
OPOMBA: Dodatek B vsebuje usmeritve za napajalne sisteme z enosmerno napetostjo – 60 V.

General Information

Status
Published
Publication Date
14-Apr-2019
Technical Committee
Current Stage
12 - Completion
Due Date
23-Apr-2019
Completion Date
15-Apr-2019
Mandate

Buy Standard

Standard
ETSI EN 300 132-2 V2.6.1 (2019-04) - Environmental Engineering (EE); Power supply interface at the input of Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current (DC)
English language
37 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
EN 300 132-2 V2.6.1:2019
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 300 132-2 V2.5.9 (2019-01) - Environmental Engineering (EE); Power supply interface at the input of Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current (DC)
English language
37 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

ETSI EN 300 132-2 V2.6.1 (2019-04)
EUROPEAN STANDARD
Environmental Engineering (EE);
Power supply interface at the input of
Information and Communication Technology (ICT) equipment;
Part 2: -48 V Direct Current (DC)
---------------------- Page: 1 ----------------------
2 ETSI EN 300 132-2 V2.6.1 (2019-04)
Reference
REN/EE-0270
Keywords
interface, power supply
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 132-2 V2.6.1 (2019-04)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definition of terms, symbols and abbreviations ....................................................................................... 8

3.1 Terms .................................................................................................................................................................. 8

3.2 Symbols .............................................................................................................................................................. 9

3.3 Abbreviations ..................................................................................................................................................... 9

4 Requirements ............................................................................................................................................ 9

4.0 Power interface "A" ............................................................................................................................................ 9

4.1 Nominal voltage ............................................................................................................................................... 10

4.2 Normal service voltage range at interface "A" ................................................................................................. 10

4.3 Abnormal service voltage range at interface "A" ............................................................................................. 11

4.3.1 Abnormal service voltage range under steady state conditions .................................................................. 11

4.3.2 Abnormal conditions: voltage variations, dips and short interruptions ....................................................... 11

4.3.3 Voltage transients ....................................................................................................................................... 12

4.3.3.1 Voltage transient due to short-circuit and protective device clearance ................................................. 12

4.3.3.2 Short voltage transient due to switching and lightning ......................................................................... 12

4.3.4 Recovery from voltage transients ............................................................................................................... 13

4.4 Voltage changes due to the regulation of the power supply ............................................................................. 14

4.5 Power supply protection at interface "A" ......................................................................................................... 14

4.6 Maximum current drain .................................................................................................................................... 14

4.7 Inrush Current on connection of interface "A" ................................................................................................. 15

4.7.1 Limits .......................................................................................................................................................... 15

4.7.2 Measurements ............................................................................................................................................. 16

4.8 Conducted immunity requirements of the ICT equipment at interface "A": narrowband noise ....................... 17

4.9 Conducted emissions requirements of the ICT equipment at interface "A" ..................................................... 19

5 Earthing and bonding ............................................................................................................................. 20

Annex A (informative): Identification of interface "A" ...................................................................... 21

Annex B (informative): -60 VDC systems ............................................................................................ 22

Annex C (informative): Guide for measuring inrush current and for transferring the

recorded pulses onto the limit chart ............................................................. 23

C.1 Measurement .......................................................................................................................................... 23

C.2 Pulse waveform transfor mation .............................................................................................................. 23

C.3 Measurement of inrush current with filter capacitor current pulses ....................................................... 26

Annex D (informative): Test arrangements for the injection of electrical noise at interface

"A" .................................................................................................................. 29

Annex E (informative): Wideband noise .............................................................................................. 30

E.0 Wideband noise ...................................................................................................................................... 30

E.1 Emission of wideband noise ................................................................................................................... 30

E.1.0 General ............................................................................................................................................................. 30

E.1.1 Assessment of wideband noise ......................................................................................................................... 30

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 132-2 V2.6.1 (2019-04)

E.2 How to calculate wideband emission ..................................................................................................... 30

Annex F (informative): Protection dimensioning ................................................................................ 34

Annex G (informative): Effects of protective device operation transients in the power

distribution ..................................................................................................... 35

Annex H (informative): Bibliography ................................................................................................... 36

History .............................................................................................................................................................. 37

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 132-2 V2.6.1 (2019-04)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).

The present document concerns the requirements for the interface between ICT equipment and its power supply, and

includes requirements relating to its stability and measurement. Various other references and detailed measurement and

test arrangements are contained in informative annexes.

The present document is part 2 of a multi-part deliverable covering Environmental Engineering (EE); Power supply

interface at the input to Information and Communication Technology (ICT) equipment, as identified below:

Part 1: "Alternating Current (AC)";
Part 2: "-48 V Direct Current (DC)";
Part 3: "Up to 400 V Direct Current (DC)".
National transposition dates
Date of adoption of this EN: 9 April 2019
Date of latest announcement of this EN (doa): 31 July 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2020
Date of withdrawal of any conflicting National Standard (dow): 31 January 2020
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 132-2 V2.6.1 (2019-04)
1 Scope

The present document contains requirements and measurements methods for the physical interface "A" that is situated

between the power supply system(s) and the power consuming ICT equipment.

The nominal voltage at power interface "A" of ICT equipment defined in the present document is DC voltage -48 V.

The DC power can be supplied by a DC output power system (e.g. based on AC rectifiers on grid or DC/DC converters on

solar system, fuel cell, DC engine or fuel cell generator) and also directly supplied by a battery backup in this DC power

system. The purpose of the present document is to use a power supply system with the same characteristics for all ICT

equipment defined in the area of application:
- to facilitate inter working of different types of load units;
- to facilitate the standardization of ICT equipment;

- to facilitate the installation, operation and maintenance in the same network of ICT equipment and systems

from different origins.

The present document aims at providing electrical compatibility between the power supply equipment and the power

consuming ICT equipment, between different system blocks and loads connected to the same power supply feeding the

interface "A" (e.g. control/monitoring, cooling system, etc.).
The requirements are defined for:

- the power supply input of any type of ICT equipment installed at telecommunication centres that are connected

to interface "A" powered by DC;

- any type of ICT equipment, installed in access networks and customers' premises, the DC interface "A" of

which is also used by equipment requiring a DC supply source;

- any type of ICT equipment powered by DC, used in the fixed and mobile networks installed in different

locations such as buildings, shelters, street cabinets.

Disturbances on the power supply interface "A" relating to the continuous wave phenomena below 20 kHz are covered

within the present document.

The present document does not cover safety requirements, they are covered by relevant safety standards.

The present document does not cover EMC requirements, they are covered by relevant EMC standards.

NOTE: Annex B gives guidance on -60 VDC supply systems.
2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] Void.
[2] Void.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 132-2 V2.6.1 (2019-04)
[3] Void.
[4] Void.

[5] CENELEC EN 61000-4-5: "Electromagnetic compatibility (EMC) - Part 4-5: Testing and

measurement techniques - Surge immunity test".
[6] Void.

[7] CENELEC EN 61000-4-29: "Electromagnetic compatibility (EMC) - Part 4-29: Testing and

measurement techniques -Voltage dips, short interruptions and voltage variations on d.c. input

power port immunity tests".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Recommendation ITU-T Q.551: "Transmission characteristics of digital exchanges".

[i.2] Recommendation ITU-T Q.552: "Transmission characteristics at 2-wire analogue interfaces of

digital exchanges".

[i.3] Recommendation ITU-T Q.553: "Transmission characteristics at 4-wire analogue interfaces of

digital exchanges".

[i.4] Recommendation ITU-T Q.554: "Transmission characteristics at digital interfaces of digital

exchanges".

[i.5] ETSI TR 100 283: "Environmental Engineering (EE); Transient voltages at Interface "A" on

telecommunications direct current (dc) power distributions".

[i.6] US Department of Defence MIL-STD-461E: "Requirements for the control of electromagnetic

interference characteristics of subsystems and equipment".

[i.7] ETSI EN 300 253: "Environmental Engineering (EE); Earthing and bonding of ICT equipment

powered by -48 VDC in telecom and data centres".

[i.8] Recommendation ITU-T O.41: "Psophometer for use on telephone-type circuits".

[i.9] IEC 60050-601: "International Electrotechnical Vocabulary. Chapter 601: Generation,

transmission and distribution of electricity - General" (Area 826 "Electrical installations",

section 826-11 "Voltages and currents").
[i.10] CENELEC EN 60269-1: "Low-voltage fuses - Part 1: General requirements".
[i.11] CENELEC EN 60934: "Circuit-breakers for equipment (CBE)".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 300 132-2 V2.6.1 (2019-04)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

abnormal service voltage range: range of steady-state voltage over which the equipment will not be expected to

maintain normal service but will survive undamaged
customer premises: location which is the sole responsibility of the customer
DC power return conductor: 0 V power supply conductor
NOTE: Also called "battery return".

fully equipped equipment: configuration that corresponds to the maximum power consumption measured at -48 VDC

with the equipment in operating conditions (e.g. not in standby mode)

NOTE: When there are several fully equipped configurations because of different combinations of possible

boards, the configuration with the boards that gives the highest power consumption should be considered.

ICT equipment: device, in the telecommunication network infrastructure, that provides an ICT service

interface "A": terminals at which the power supply is connected to the system block

NOTE 1: See also figure 1 and annex A.

NOTE 2: This is a functional definition and not an exact depiction of the physical location.

malfunction: termination of the normal service

maximum steady state input current (I ): maximum steady state input current, stated by the manufacturer, for a fully

equipped equipment under test connected to interface "A" at nominal voltage

nominal voltage: value of the voltage by which the electrical installation or part of the electrical installation is

designated and identified [i.9]

normal service: service mode where ICT equipment operates within its specification which includes a defined restart

time after malfunction or full interruption

normal service voltage range: range of steady-state voltages over which the equipment will maintain normal service

power supply: power source to which ICT equipment is intended to be connected

service voltage: value of the voltage under normal conditions, at a given instant and a given point of the system [i.9]

system block: functional group of equipment depending for its operation and performance on its connection to the same

power supply

NOTE: A system block may consist of equipment or a functional group of equipment. Different examples of

configurations at interface "A" are given in annex A.

telecommunication centre: location where ICT equipment is installed and which is the sole responsibility of the

operator
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 300 132-2 V2.6.1 (2019-04)
3.2 Symbols
For the purposes of the present document, the following symbols apply:
I instantaneous inrush current
I maximum steady state input current
L inductance of inductive element of LISN
R resistance of resistive element of LISN
t time
pso,eff effective psophometric voltage
rms RMS voltage
Z capacitive impedance of immunity measurement circuit
Z resistive impedance of immunity measurement circuit
μs microsecond
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
DC Direct Current
NOTE: Also when used as a suffix to units of measurement.
EMC ElectroMagnetic Compatibility
ESR Equivalent Series Resistance
EUT Equipment Under Test
HOD High-Ohmic Distributions
ICT Information and Communication Technology
LISN Line Impedance Stabilization Network
LOD Low-Ohmic Distributions
RF Radio Frequency
rms root mean square
TR Technical Report
VDC Voltage Direct Current
NOTE: Also when used as a suffix to units of measurement.
4 Requirements
4.0 Power interface "A"

The power supply interface, interface "A" of figure 1, is a physical point to which all the requirements are related.

This point is situated between the power supply system(s) and the power consuming ICT equipment.

An example of a configuration in which interface "A" is identified is given in annex A.

ETSI
---------------------- Page: 9 ----------------------
10 ETSI EN 300 132-2 V2.6.1 (2019-04)
ICT equipment
Figure 1: Identification of interface "A"
4.1 Nominal voltage

The interface and equipment shall be designated and identified by a nominal voltage.

The nominal voltage at interface "A" shall be -48 VDC with positive conductor connected to earth as defined in ETSI

EN 300 253 [i.7].

NOTE 1: The positive conductor, also called DC return, can be (see ETSI EN 300 253 [i.7]:

 Isolated DC return: this is a DC power system in which the DC power return conductor has a single

point connection to the bonding network. Equipment intended for this power distribution has a

floating DC power at the power input terminal.

 Common DC return: this is a DC power system in which the return conductor is connected to the

bonding network at many points. Equipment intended for this power distribution can have the DC

return earthed at the power input terminal.

NOTE 2: In most cases the nominal voltage of interface "A" is based on a 24 cells lead-acid battery. Use of other

technologies, such as Lithium-ion batteries, are increasing.
4.2 Normal service voltage range at interface "A"

The normal service voltage range for the -48 VDC nominal supply at interface "A" shall be from -40,5 VDC

to -57,0 VDC.

There shall be no degradation of service performance when ICT equipment is operating at voltages within the normal

service voltage range including voltage variation inside the normal voltage range.

This requirement shall be verified by applying at interface "A" a voltage step test with specification and parameters

defined in table 1. The testing and measurement techniques are described in CENELEC EN 61000-4-29 [7].

The test shall apply to equipment with single and multiple power supply "A" interface inputs.

ETSI
---------------------- Page: 10 ----------------------
11 ETSI EN 300 132-2 V2.6.1 (2019-04)
Table 1

Test level of Normal Voltage Basic standard Rise and fall time of Performance criteria

service voltage step step for testing voltage step
variation Duration
From -40,5 V to -57,0 VDC 0,1 s CENELEC No degradation in the
Between 1 μs and 50 μs on

From -57,0 V to -40,5 VDC 0,1 s EN 61000-4-29 [7] 100 Ω resistive load service performance

during and after the
(see basic standard for test
test
generator)

In the case of ICT equipment with power supply input redundancy (e.g. Input 1 and Input 2), this test shall be

performed:

• with Inputs 1 and 2 powered simultaneously and applying the test in table 1 on both inputs simultaneously;

• with Inputs 1 and 2 powered simultaneously and applying the test in table 1 on one input (either Input 1 or 2);

• with either Input 1 or 2 powered and no power on the other power input and applying the test in table 1 on the

powered input.

NOTE 1: The minimum voltage is based on the voltage drop in the distribution network and a battery cell end of

discharge voltage.

NOTE 2: The voltages specified are measured at interface "A". It should be noted that if interface "A" is at any

point other than the ICT equipment interface as presented in annex A, there will be a voltage drop

between interface "A" and the equipment terminals.
4.3 Abnormal service voltage range at interface "A"
4.3.1 Abnormal service voltage range under steady state conditions

ICT equipment designed to work at 48 VDC nominal voltage at the interface "A" shall not suffer any damage when

subjected to the following voltage ranges defined in table 2.
Table 2
0,0 V to -40,5 VDC and
-57,0 VDC to -60,0 VDC

Following the restoration of the supply to the normal voltage range, the power conversion and management systems on

the load side of interface "A" shall automatically restore normal service. The ICT equipment shall then resume

operation according to its specifications. The abnormal service voltage shall not lead to the disconnection of the power

supply e.g. by causing circuit breakers, fuses or other such devices to operate.

NOTE: It is acceptable that the system may restart when the voltage is -40,5 VDC or anywhere within the

nominal service voltage range and/or after a time delay.
4.3.2 Abnormal conditions: voltage variations, dips and short interruptions

ICT equipment shall comply with the requirements defined in this clause when subject to the abnormal voltage range

defined in table 3 that can be present at the interface "A".

This requirement shall be verified by applying at interface "A" a voltage step test with specification and parameters

defined in table 3. The testing and measurement techniques are described in CENELEC EN 61000-4-29 [7].

The test shall apply to equipment with single and multiple power supply inputs.
ETSI
---------------------- Page: 11 ----------------------
12 ETSI EN 300 132-2 V2.6.1 (2019-04)
Table 3

Test level of abnormal Voltage step Basic standard Rise and fall time of Performance criteria

voltage step variation Duration for testing voltage step
From -40,5 VDC to -60,0 VDC 0,1 s CENELEC Self restart to a normal
Between 1 μs and 50 μs
and from -60 VDC to -40,5 VDC EN 61000-4-29 [7] service of the equipment
on 100 Ω resistive load
From -57,0 VDC to 0,0 V and 0,1 s (see basic standard) without operator
intervention after the test
from 0,0 V to -57,0 VDC

In the case of ICT equipment with power supply input redundancy (e.g. Input 1 and Input 2), this test shall be

performed:

• with Inputs 1 and 2 powered simultaneously and applying the test in table 3 on both inputs simultaneously;

• with Inputs 1 and 2 powered simultaneously and applying the test in table 3 on one input (either Input 1 or 2).

In this case the performance criteria shall be "No degradation in the service performance during and after the

test";

• with either Input 1 or 2 powered and no power on the other power input and applying the test in table 3 on the

powered input.
4.3.3 Voltage transients
4.3.3.1 Voltage transient due to short-circuit and protective device clearance

Voltage transients may occur at interface "A" when faults (e.g. short circuits) occur in the power distribution system.

These transients are characterized by a voltage drop in the range: 0 V to -40,5 VDC, followed by an overvoltage often

in excess of the maximum steady state abnormal service voltage range defined in table 3 and dependent upon the power

distribution up to interface "A" and the equipment connected to interface "A".

NOTE 1: ETSI TR 100 283 [i.5] provides guidance for the protection of ICT equipment from the transients.

NOTE 2: A protective device operation transient results from a low impedance fault to ground on the equipment

side of a protective device (fuse or circuit breaker) connected to a power distribution bus. In the power

bus, then voltage is reduced (undervoltage) due to high current flowing to ground through the protective

device and the short ground. When the protective device opens, the release energy stored in the

inductance of the bus causes an initial high voltage overshoot of short duration, followed by a longer

interval voltage overshoot that decays toward the steady state bus voltage. The undervoltage portion of

the protective device operation transient, may cause a voltage drop at the input terminals of the other

equip
...

SLOVENSKI

STANDARD SIST EN 300 132-2 V2.6.1:201901-junij-2019Okoljski inženiring (EE) - Napajalni vmesnik na vhodu informacijske in komunikacijske tehnologije (IKT) - 2. del: Enosmerna napetost - 48 V (DC)Environmental Engineering (EE) - Power supply interface at the input of Information and Communication Technology (ICT) equipment - Part 2: -48 V Direct Current (DC)Ta slovenski standard je istoveten z:ETSI EN 300 132-2 V2.6.1 (2019-04)19.040Preskušanje v zvezi z okoljemEnvironmental testing33.050.01Telekomunikacijska terminalska oprema na splošnoTelecommunication terminal equipment in generalICS:SIST EN 300 132-2 V2.6.1:2019en2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 300 132-2 V2.6.1:2019

wwwwwETSI EN 300 132-2 V2.6.1 (2019-04) Environmental Engineering (EE); Power supply interface at the input of Information and Communication Technology (ICT) equipment; Part 2: -48 V Direct Current (DC)

EUROPEAN STANDARD SIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 2 wwwoeferencewREN/EE-0270 heywordswinterface, power supply ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCEw Tel.: +33 4 92 94 42 00

Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI deliverable is the one made publicly available in PDF format at www.etsi.org/deliver. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the oneM2M Partners. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 3 Contents fntellectualwmropertywoightswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwo corewordwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwo jodalwverbswterminologywhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwo k pcopewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwp lwoeferenceswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwp lhkwkormativewreferenceswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwp lhlwfnformativewreferenceswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwq mwaefinitionwofwtermsfwsymbolswandwabbreviationswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwr mhkwqermswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwr mhlwpymbolswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhws mhmwAbbreviationswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhws nwoequirementswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhws nhjwmowerwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhws nhkwkominalwvoltagewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkj nhlwkormalwservicewvoltagewrangewatwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkj nhmwAbnormalwservicewvoltagewrangewatwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkk nhmhkwAbnormalwservicewvoltagewrangewunderwsteadywstatewconditionswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkk nhmhlwAbnormalwconditionstwvoltagewvariationsfwdipswandwshortwinterruptionswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkk nhmhmwsoltagewtransientswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkl nhmhmhkwsoltagewtransientwduewtowshortgcircuitwandwprotectivewdevicewclearancewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkl nhmhmhlwphortwvoltagewtransientwduewtowswitchingwandwlightningwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkl nhmhnwoecoverywfromwvoltagewtransientswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkm nhnwsoltagewchangeswduewtowthewregulationwofwthewpowerwsupplywhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkn nhowmowerwsupplywprotectionwatwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkn nhpwjaximumwcurrentwdrainwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkn nhqwfnrushwCurrentwonwconnectionwofwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwko nhqhkwiimitswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwko nhqhlwjeasurementswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwkp nhrwConductedwimmunitywrequirementswofwthewfCqwequipmentwatwinterfacew"A"twnarrowbandwnoisewhhhhhhhhhhhhhhhhhhhhhhhwkq nhswConductedwemissionswrequirementswofwthewfCqwequipmentwatwinterfacew"A"whhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwks owbarthingwandwbondingwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwlj Annex A (informative): Identification of interface "A" ...................................................................... 21 Annex B (informative): -60 VDC systems ............................................................................................ 22 Annex C (informative): Guide for measuring inrush current and for transferring the recorded pulses onto the limit chart ............................................................. 23 Chkwjeasurementwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwlm Chlwmulsewwaveformwtransformationwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwlm Chmwjeasurementwofwinrushwcurrentwwithwfilterwcapacitorwcurrentwpulseswhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwlp Annex D (informative): Test arrangements for the injection of electrical noise at interface "A" .................................................................................................................. 29 Annex E (informative): Wideband noise .............................................................................................. 30 bhjwtidebandwnoisewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmj bhkwbmissionwofwwidebandwnoisewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmj bhkhjwdeneralwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmj bhkhkwAssessmentwofwwidebandwnoisewhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmj SIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 4 bhlweowwtowcalculatewwidebandwemissionwhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmj Annex F (informative): Protection dimensioning ................................................................................ 34 Annex G (informative): Effects of protective device operation transients in the power distribution ..................................................................................................... 35 Annex H (informative): Bibliography ................................................................................................... 36 eistorywhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhwmq wSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 5 Intellectual Property Rights Essential patents fmoswessentialworwpotentiallywessentialwtownormativewdeliverableswmaywhavewbeenwdeclaredwtowbqpfhwqhewinformationwpertainingwtowthesewessentialwfmosfwifwanyfwiswpubliclywavailablewforwETSI members and non-membersfwandwcanwbewfoundwinwbqpfwpowjjjwmkntw"Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards"fwwhichwiswavailablewfromwthewbqpfwpecretariathwiatestwupdateswarewavailablewonwthewbqpfwtebwserverwbhttpstiiiprhetsihorgichwmursuantwtowthewbqpfwfmowmolicyfwnowinvestigationfwincludingwfmowsearchesfwhaswbeenwcarriedwoutwbywbqpfhwkowguaranteewcanwbewgivenwaswtowthewexistencewofwotherwfmoswnotwreferencedwinwbqpfwpowjjjwmknwborwthewupdateswonwthewbqpfwtebwservercwwhichwarefworwmaywbefworwmaywbecomefwessentialwtowthewpresentwdocumenthwTrademarks qhewpresentwdocumentwmaywincludewtrademarkswandiorwtradenameswwhichwarewassertedwandiorwregisteredwbywtheirwownershwbqpfwclaimswnowownershipwofwthesewexceptwforwanywwhichwarewindicatedwaswbeingwthewpropertywofwbqpffwandwconveyswnowrightwtowuseworwreproducewanywtrademarkwandiorwtradenamehwjentionwofwthosewtrademarkswinwthewpresentwdocumentwdoeswnotwconstitutewanwendorsementwbywbqpfwofwproductsfwservicesworworganizationswassociatedwwithwthosewtrademarkshwForeword qhiswburopeanwptandardwbbkcwhaswbeenwproducedwbywbqpfwqechnicalwCommitteewbnvironmentalwbngineeringwbbbchwqhewpresentwdocumentwconcernswthewrequirementswforwthewinterfacewbetweenwfCqwequipmentwandwitswpowerwsupplyfwandwincludeswrequirementswrelatingwtowitswstabilitywandwmeasurementhwsariouswotherwreferenceswandwdetailedwmeasurementwandwtestwarrangementswarewcontainedwinwinformativewannexeshwqhewpresentwdocumentwiswpartwlwofwawmultigpartwdeliverablewcoveringwbnvironmentalwbngineeringwbbbc;wmowerwsupplywinterfacewatwthewinputwtowfnformationwandwCommunicationwqechnologywbfCqcwequipmentfwaswidentifiedwbelowtwmartwktw"AlternatingwCurrentwbACc";wPart 2: "-48 V Direct Current (DC)"; martwmtw"rpwtownjjwswairectwCurrentwbaCc"hwwNational transposition dates aatewofwadoptionwofwthiswbktwswAprilwljkswaatewofwlatestwannouncementwofwthiswbkwbdoactwmkwgulywljkswaatewofwlatestwpublicationwofwnewwkationalwptandardworwendorsementwofwthiswbkwbdopiectwwmkwganuarywljljwaatewofwwithdrawalwofwanywconflictingwkationalwptandardwbdowctwmkwganuarywljljwwModal verbs terminology fnwthewpresentwdocumentw"shall"fw"shall not"fw"should"fw"should not"fw"may"fw"need not"fw"will"fw"will not"fw"can"wandw"cannot"warewtowbewinterpretedwaswdescribedwinwclausewmhlwofwthewbqpfwaraftingwouleswbserbalwformswforwthewexpressionwofwprovisionschw"must"wandw"must not"warewNOTwallowedwinwbqpfwdeliverableswexceptwwhenwusedwinwdirectwcitationhwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 6 1 Scope qhewpresentwdocumentwcontainswrequirementswandwmeasurementswmethodswforwthewphysicalwinterfacew"A"wthatwiswsituatedwbetweenwthewpowerwsupplywsystembscwandwthewpowerwconsumingwfCqwequipmenthwqhewnominalwvoltagewatwpowerwinterfacew"A"wofwfCqwequipmentwdefinedwinwthewpresentwdocumentwiswaCwvoltagewgnrwshwqhewaCwpowerwcanwbewsuppliedwbywawaCwoutputwpowerwsystemwbehghwbasedwonwACwrectifierswonwgridworwaCiaCwconverterswonwsolarwsystemfwfuelwcellfwaCwengineworwfuelwcellwgeneratorcwandwalsowdirectlywsuppliedwbywawbatterywbackupwinwthiswaCwpowerwsystemhwqhewpurposewofwthewpresentwdocumentwiswtowusewawpowerwsupplywsystemwwithwthewsamewcharacteristicswforwallwfCqwequipmentwdefinedwinwthewareawofwapplicationtwgwtowfacilitatewinterwworkingwofwdifferentwtypeswofwloadwunits;wgwtowfacilitatewthewstandardizationwofwfCqwequipment;wgwtowfacilitatewthewinstallationfwoperationwandwmaintenancewinwthewsamewnetworkwofwfCqwequipmentwandwsystemswfromwdifferentworiginshwqhewpresentwdocumentwaimswatwprovidingwelectricalwcompatibilitywbetweenwthewpowerwsupplywequipmentwandwthewpowerwconsumingwfCqwequipmentfwbetweenwdifferentwsystemwblockswandwloadswconnectedwtowthewsamewpowerwsupplywfeedingwthewinterfacew"A"wbehghwcontrolimonitoringfwcoolingwsystemfwetchchwqhewrequirementswarewdefinedwfortwgwthewpowerwsupplywinputwofwanywtypewofwfCqwequipmentwinstalledwatwtelecommunicationwcentreswthatwarewconnectedwtowinterfacew"A"wpoweredwbywaC;wgwanywtypewofwfCqwequipmentfwinstalledwinwaccesswnetworkswandwcustomersawpremisesfwthewaCwinterfacew"A"wofwwhichwiswalsowusedwbywequipmentwrequiringwawaCwsupplywsource;wgwanywtypewofwfCqwequipmentwpoweredwbywaCfwusedwinwthewfixedwandwmobilewnetworkswinstalledwinwdifferentwlocationswsuchwaswbuildingsfwsheltersfwstreetwcabinetshwaisturbanceswonwthewpowerwsupplywinterfacew"A"wrelatingwtowthewcontinuouswwavewphenomenawbelowwljwkezwarewcoveredwwithinwthewpresentwdocumenthwqhewpresentwdocumentwdoeswnotwcoverwsafetywrequirementsfwtheywarewcoveredwbywrelevantwsafetywstandardshwqhewpresentwdocumentwdoeswnotwcoverwbjCwrequirementsfwtheywarewcoveredwbywrelevantwbjCwstandardshwklqbtwAnnexwBwgiveswguidancewonwgpjwsaCwsupplywsystemshw2 References 2.1 Normative references oeferenceswareweitherwspecificwbidentifiedwbywdatewofwpublicationwandiorweditionwnumberworwversionwnumbercworwnongspecifichwcorwspecificwreferencesfwonlywthewcitedwversionwapplieshwcorwnongspecificwreferencesfwthewlatestwversionwofwthewreferencedwdocumentwbincludingwanywamendmentscwapplieshwoeferencedwdocumentswwhichwarewnotwfoundwtowbewpubliclywavailablewinwthewexpectedwlocationwmightwbewfoundwatwhttpstiidocboxhetsihorgioeferenceihwklqbtwthilewanywhyperlinkswincludedwinwthiswclausewwerewvalidwatwthewtimewofwpublicationfwbqpfwcannotwguaranteewtheirwlongwtermwvalidityhwqhewfollowingwreferencedwdocumentswarewnecessarywforwthewapplicationwofwthewpresentwdocumenthwxkzwsoidhwxlzwsoidhwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 7 xmzwsoidhwxnzwsoidhwxozwCbkbibCwbkwpkjjjgngotw"blectromagneticwcompatibilitywbbjCcwgwmartwngotwqestingwandwmeasurementwtechniqueswgwpurgewimmunitywtest"hwxpzwsoidhwxqzwCbkbibCwbkwpkjjjgnglstw"blectromagneticwcompatibilitywbbjCcwgwmartwnglstwqestingwandwmeasurementwtechniqueswgsoltagewdipsfwshortwinterruptionswandwvoltagewvariationswonwdhchwinputwpowerwportwimmunitywtests"hw2.2 Informative references oeferenceswareweitherwspecificwbidentifiedwbywdatewofwpublicationwandiorweditionwnumberworwversionwnumbercworwnongspecifichwcorwspecificwreferencesfwonlywthewcitedwversionwapplieshwcorwnongspecificwreferencesfwthewlatestwversionwofwthewreferencedwdocumentwbincludingwanywamendmentscwapplieshwklqbtwthilewanywhyperlinkswincludedwinwthiswclausewwerewvalidwatwthewtimewofwpublicationfwbqpfwcannotwguaranteewtheirwlongwtermwvalidityhwqhewfollowingwreferencedwdocumentswarewnotwnecessarywforwthewapplicationwofwthewpresentwdocumentwbutwtheywassistwthewuserwwithwregardwtowawparticularwsubjectwareahwxihkzwoecommendationwfqrgqwnhooktw"qransmissionwcharacteristicswofwdigitalwexchanges"hwxihlzwoecommendationwfqrgqwnhooltw"qransmissionwcharacteristicswatwlgwirewanaloguewinterfaceswofwdigitalwexchanges"hwxihmzwoecommendationwfqrgqwnhoomtw"qransmissionwcharacteristicswatwngwirewanaloguewinterfaceswofwdigitalwexchanges"hwxihnzwoecommendationwfqrgqwnhoontw"qransmissionwcharacteristicswatwdigitalwinterfaceswofwdigitalwexchanges"hwxihozwbqpfwqowkjjwlrmtw"bnvironmentalwbngineeringwbbbc;wqransientwvoltageswatwfnterfacew"A"wonwtelecommunicationswdirectwcurrentwbdccwpowerwdistributions"hwxihpzwrpwaepartmentwofwaefencewjfigpqagnpkbtw"oequirementswforwthewcontrolwofwelectromagneticwinterferencewcharacteristicswofwsubsystemswandwequipment"hwxihqzwbqpfwbkwmjjwlomtw"bnvironmentalwbngineeringwbbbc;wbarthingwandwbondingwofwfCqwequipmentwpoweredwbywgnrwsaCwinwtelecomwandwdatawcentres"hwxihrzwoecommendationwfqrgqwlhnktw"msophometerwforwusewonwtelephonegtypewcircuits"hwxihszwfbCwpjjojgpjktw"fnternationalwblectrotechnicalwsocabularyhwChapterwpjktwdenerationfwtransmissionwandwdistributionwofwelectricitywgwdeneral"wbAreawrlpw"blectricalwinstallations"fwsectionwrlpgkkw"soltageswandwcurrents"chwxihkjzwCbkbibCwbkwpjlpsgktw"iowgvoltagewfuseswgwmartwktwdeneralwrequirements"hwxihkkzwCbkbibCwbkwpjsmntw"CircuitgbreakerswforwequipmentwbCBbc"hwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 8 3 Definition of terms, symbols and abbreviations 3.1 Terms corwthewpurposeswofwthewpresentwdocumentfwthewfollowingwtermswapplytwabnormal service voltage range: rangewofwsteadygstatewvoltagewoverwwhichwthewequipmentwwillwnotwbewexpectedwtowmaintainwnormalwservicewbutwwillwsurvivewundamagedwcustomer premises:wlocationwwhichwiswthewsolewresponsibilitywofwthewcustomerwDC power return conductor: jwswpowerwsupplywconductorwklqbtwAlsowcalledw"batterywreturn"hwfully equipped equipment: configurationwthatwcorrespondswtowthewmaximumwpowerwconsumptionwmeasuredwatwgnrwsaCwwithwthewequipmentwinwoperatingwconditionswbehghwnotwinwstandbywmodecwklqbtwthenwtherewarewseveralwfullywequippedwconfigurationswbecausewofwdifferentwcombinationswofwpossiblewboardsfwthewconfigurationwwithwthewboardswthatwgiveswthewhighestwpowerwconsumptionwshouldwbewconsideredhwICT equipment: devicefwinwthewtelecommunicationwnetworkwinfrastructurefwthatwprovideswanwfCqwservicewinterface "A": terminalswatwwhichwthewpowerwsupplywiswconnectedwtowthewsystemwblockwklqbwktwpeewalsowfigurewkwandwannexwAhwklqbwltwqhiswiswawfunctionalwdefinitionwandwnotwanwexactwdepictionwofwthewphysicalwlocationhwmalfunction: terminationwofwthewnormalwservicewmaximum steady state input current (Im):wmaximumwsteadywstatewinputwcurrentfwstatedwbywthewmanufacturerfwforwawfullywequippedwequipmentwunderwtestwconnectedwtowinterfacew"A"watwnominalwvoltage nominal voltage: valuewofwthewvoltagewbywwhichwthewelectricalwinstallationworwpartwofwthewelectricalwinstallationwiswdesignatedwandwidentifiedwxihszwnormal service: servicewmodewwherewfCqwequipmentwoperateswwithinwitswspecificationwwhichwincludeswawdefinedwrestartwtimewafterwmalfunctionworwfullwinterruptionwnormal service voltage range: rangewofwsteadygstatewvoltageswoverwwhichwthewequipmentwwillwmaintainwnormalwservicewpower supply:wpowerwsourcewtowwhichwfCqwequipmentwiswintendedwtowbewconnectedwservice voltage: valuewofwthewvoltagewunderwnormalwconditionsfwatwawgivenwinstantwandwawgivenwpointwofwthewsystemwxihszwsystem block: functionalwgroupwofwequipmentwdependingwforwitswoperationwandwperformancewonwitswconnectionwtowthewsamewpowerwsupplywklqbtwAwsystemwblockwmaywconsistwofwequipmentworwawfunctionalwgroupwofwequipmenthwaifferentwexampleswofwconfigurationswatwinterfacew"A"warewgivenwinwannexwAhwtelecommunication centre:wlocationwwherewfCqwequipmentwiswinstalledwandwwhichwiswthewsolewresponsibilitywofwthewoperatorwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 9 3.2 Symbols corwthewpurposeswofwthewpresentwdocumentfwthewfollowingwsymbolswapplytwftwinstantaneouswinrushwcurrentwfmwmaximumwsteadywstatewinputwcurrentwiwinductancewofwinductivewelementwofwifpkwowresistancewofwresistivewelementwofwifpkwtwtimewrpsofeffweffectivewpsophometricwvoltagewrrmswojpwvoltagewwcwcapacitivewimpedancewofwimmunitywmeasurementwcircuitwwmwresistivewimpedancewofwimmunitywmeasurementwcircuitwμswmicrosecondw3.3 Abbreviations corwthewpurposeswofwthewpresentwdocumentfwthewfollowingwabbreviationswapplytwACwAlternatingwCurrentwaCwairectwCurrentwklqbtwAlsowwhenwusedwaswawsuffixwtowunitswofwmeasurementhwbjCwblectrojagneticwCompatibilitywbpowbquivalentwperieswoesistancewbrqwbquipmentwrnderwqestwelaweighglhmicwaistributionswfCqwfnformationwandwCommunicationwqechnologywifpkwiinewfmpedancewptabilizationwketworkwilawiowglhmicwaistributionswocwoadiowcrequencywrmswrootwmeanwsquarewqowqechnicalwoeportwsaCwsoltagewairectwCurrentwklqbtwAlsowwhenwusedwaswawsuffixwtowunitswofwmeasurementhw4 Requirements 4.0 Power interface "A" qhewpowerwsupplywinterfacefwinterfacew"A"wofwfigurewkfwiswawphysicalwpointwtowwhichwallwthewrequirementswarewrelatedhwwqhiswpointwiswsituatedwbetweenwthewpowerwsupplywsystembscwandwthewpowerwconsumingwfCqwequipmenthwAnwexamplewofwawconfigurationwinwwhichwinterfacew"A"wiswidentifiedwiswgivenwinwannexwAhwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 10

Figure 1: Identification of interface "A" 4.1 Nominal voltage qhewinterfacewandwequipmentwshallwbewdesignatedwandwidentifiedwbywawnominalwvoltagehwqhewnominalwvoltagewatwinterfacew"A"wshallwbewgnrwsaCwwithwpositivewconductorwconnectedwtowearthwaswdefinedwinwbqpfwbkwmjjwlomwxihqzhwklqbwktwqhewpositivewconductorfwalsowcalledwaCwreturnfwcanwbewbseewbqpfwbkwmjjwlomwxihqztw fsolatedwaCwreturntwthiswiswawaCwpowerwsystemwinwwhichwthewaCwpowerwreturnwconductorwhaswawsinglewpointwconnectionwtowthewbondingwnetworkhwbquipmentwintendedwforwthiswpowerwdistributionwhaswawfloatingwaCwpowerwatwthewpowerwinputwterminalhw CommonwaCwreturntwthiswiswawaCwpowerwsystemwinwwhichwthewreturnwconductorwiswconnectedwtowthewbondingwnetworkwatwmanywpointshwbquipmentwintendedwforwthiswpowerwdistributionwcanwhavewthewaCwreturnwearthedwatwthewpowerwinputwterminalhwklqbwltwfnwmostwcaseswthewnominalwvoltagewofwinterfacew"A"wiswbasedwonwawlnwcellswleadgacidwbatteryhwrsewofwotherwtechnologiesfwsuchwaswiithiumgionwbatteriesfwarewincreasinghw4.2 Normal service voltage range at interface "A" qhewnormalwservicewvoltagewrangewforwthewgnrwsaCwnominalwsupplywatwinterfacew"A"wshallwbewfromwgnjfowsaCwtowgoqfjwsaChwqherewshallwbewnowdegradationwofwservicewperformancewwhenwfCqwequipmentwiswoperatingwatwvoltageswwithinwthewnormalwservicewvoltagewrangewincludingwvoltagewvariationwinsidewthewnormalwvoltagewrangehwqhiswrequirementwshallwbewverifiedwbywapplyingwatwinterfacew"A"wawvoltagewstepwtestwwithwspecificationwandwparameterswdefinedwinwtablewkhwqhewtestingwandwmeasurementwtechniqueswarewdescribedwinwCbkbibCwbkwpkjjjgnglswxqzhwqhewtestwshallwapplywtowequipmentwwithwsinglewandwmultiplewpowerwsupplyw"A"winterfacewinputshwfCqwequipmentwwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 11 Table 1 Test level of Normal service voltage step variation Voltage step Duration Basic standard for testing Rise and fall time of voltage step Performance criteria From -40,5 V to -57,0 VDC 0,1 s CENELEC EN 61000-4-29 [7] Between 1 μs and 50 μs on 100 Ω resistive load (see basic standard for test generator) No degradation in the service performance during and after the test From -57,0 V to -40,5 VDC 0,1 s wfnwthewcasewofwfCqwequipmentwwithwpowerwsupplywinputwredundancywbehghwfnputwkwandwfnputwlcfwthiswtestwshallwbewperformedtw• withwfnputswkwandwlwpoweredwsimultaneouslywandwapplyingwthewtestwinwtablewkwonwbothwinputswsimultaneously;w• withwfnputswkwandwlwpoweredwsimultaneouslywandwapplyingwthewtestwinwtablewkwonwonewinputwbeitherwfnputwkworwlc;w• withweitherwfnputwkworwlwpoweredwandwnowpowerwonwthewotherwpowerwinputwandwapplyingwthewtestwinwtablewkwonwthewpoweredwinputhwklqbwktwqhewminimumwvoltagewiswbasedwonwthewvoltagewdropwinwthewdistributionwnetworkwandwawbatterywcellwendwofwdischargewvoltagehwklqbwltwqhewvoltageswspecifiedwarewmeasuredwatwinterfacew"A"hwftwshouldwbewnotedwthatwifwinterfacew"A"wiswatwanywpointwotherwthanwthewfCqwequipmentwinterfacewaswpresentedwinwannexwAfwtherewwillwbewawvoltagewdropwbetweenwinterfacew"A"wandwthewequipmentwterminalshw4.3 Abnormal service voltage range at interface "A" 4.3.1 Abnormal service voltage range under steady state conditions fCqwequipmentwdesignedwtowworkwatwnrwsaCwnominalwvoltagewatwthewinterfacew"A"wshallwnotwsufferwanywdamagewwhenwsubjectedwtowthewfollowingwvoltagewrangeswdefinedwinwtablewlhwTable 2 0,0 V to -40,5 VDC and -57,0 VDC to -60,0 VDC wcollowingwthewrestorationwofwthewsupplywtowthewnormalwvoltagewrangefwthewpowerwconversionwandwmanagementwsystemswonwthewloadwsidewofwinterfacew"A"wshallwautomaticallywrestorewnormalwservicehwqhewfCqwequipmentwshallwthenwresumewoperationwaccordingwtowitswspecificationshwqhewabnormalwservicewvoltagewshallwnotwleadwtowthewdisconnectionwofwthewpowerwsupplywehghwbywcausingwcircuitwbreakersfwfusesworwotherwsuchwdeviceswtowoperatehwklqbtwftwiswacceptablewthatwthewsystemwmaywrestartwwhenwthewvoltagewiswgnjfowsaCworwanywherewwithinwthewnominalwservicewvoltagewrangewandiorwafterwawtimewdelayhw4.3.2 Abnormal conditions: voltage variations, dips and short interruptions fCqwequipmentwshallwcomplywwithwthewrequirementswdefinedwinwthiswclausewwhenwsubjectwtowthewabnormalwvoltagewrangewdefinedwinwtablewmwthatwcanwbewpresentwatwthewinterfacew"A"hwqhiswrequirementwshallwbewverifiedwbywapplyingwatwinterfacew"A"wawvoltagewstepwtestwwithwspecificationwandwparameterswdefinedwinwtablewmhwqhewtestingwandwmeasurementwtechniqueswarewdescribedwinwCbkbibCwbkwpkjjjgnglswxqzhwqhewtestwshallwapplywtowequipmentwwithwsinglewandwmultiplewpowerwsupplywinputshwSIST EN 300 132-2 V2.6.1:2019

ETSI ETSI EN 300 132-2 V2.6.1 (2019-04) 12 Table 3 Test level of abnormal voltage step variation Voltage step Duration Basic standard for testing Rise and fall time of voltage step Performance criteria From -40,5 VDC to -60,0 VDC and from -60 VDC to -40,5 VDC 0,1 s CENELEC EN 61000-4-29 [7] Between 1 μs and 50 μs on 100 Ω resistive load (see basic standard) Self restart to a normal service of the equipment without operator intervention after the test From -57,0 VDC to 0,0 V and from 0,0 V to -57,0 VDC 0,1 s wfnwthewcasewofwfCqwequipmentwwithwpowerwsupplywinputwredundancywbehghwfnputwkwandwfnputwlcfwthiswtestwshallwbewperformedtw• withwfnputswkwandwlwpoweredwsimultaneouslywandwapplyingwthewtestwinwtablewmwonwbothwinputswsimultaneously;w• withwfnputswkwandwlwpoweredwsimultaneouslywandwapplyingwthewtestwinwtablewmwonwonewinputwbeitherwfnputwkworwlchwfnwthiswcasewthewperformancewcriteriawshallwbew"kowdegradationwinwthewservicewperformancewduringwandwafterwthewtest";w• withweitherwfnputwkworwlwpoweredwandwnowpowerwonwthewotherwpowerwinputwandwapplyingwthewtestwinwtablewmwonwthewpoweredwinputhw4.3.3 Voltage transients 4.3.3.1 Voltage transient due to short-circuit and protective device clearance soltagewtransientswmaywoccurwatwinterfacew"A"wwhenwfaultswbehghwshortwcircuitscwoccurwinwthewpowerwdistributionwsystemhwqhesewtransientswarewcharacterizedwbywawvoltagewdropwinwthewrangetwjwswtowgnjfowsaCfwfollowedwbywanwovervoltagewoftenwinwexcesswofwthewmaximumwsteadywstatewabnormalwservicewvoltagewrangewdefinedwinwtablewmwandwdependentwuponwthewpowerwdistributionwupwtowinterfacew"A"wandwthewequipmentwconnectedwtowinterfacew"A"hwklqbwktwbqpfwqowkjjwlrmwxihozwprovideswguidancewforwthewprotectionwofwfCqwequipmentwfromwthewtransientshwklqbwltwAwprotectivewdevicewoperationwtransientwresultswfromwawlowwimpedancewfaultwtowgroundwonwthewequipmentwsidewofwawprotectivewdevicewbfuseworwcircuitwbreakercwconnectedwtowawpowerwdistributionwbushwfnwthewpowerwbusfwthenwvoltagewiswreducedwbundervoltagecwduewtowhighwcurrentwflowingwtowgroundwthroughwthewprotectivewdevicewandwthewshortwgroundhwthenwthewprotectivewdevicewopensfwthewreleasewenergywstoredwinwthewinductancewofwthewbuswcauseswanwinitialwhighwvoltagewovershootwofwshortwdurationfwfollowedwbywawlongerwintervalwvoltagewovershootwthatwdecayswtowardwthewsteadywstatewbuswvoltagehwqhewundervoltagewportionwofwthewprotectivewdevicewoper

...

Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
EUROPEAN STANDARD
Environmental Engineering (EE);
Power supply interface at the input of
Information and Communication Technology (ICT) equipment;
Part 2: -48 V Direct Current (DC)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
Reference
REN/EE-0270
Keywords
interface, power supply
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definition of terms, symbols and abbreviations ....................................................................................... 8

3.1 Terms .................................................................................................................................................................. 8

3.2 Symbols .............................................................................................................................................................. 9

3.3 Abbreviations ..................................................................................................................................................... 9

4 Requirements ............................................................................................................................................ 9

4.0 Power interface "A" ............................................................................................................................................ 9

4.1 Nominal voltage ............................................................................................................................................... 10

4.2 Normal service voltage range at interface "A" ................................................................................................. 10

4.3 Abnormal service voltage range at interface "A" ............................................................................................. 11

4.3.1 Abnormal service voltage range under steady state conditions .................................................................. 11

4.3.2 Abnormal conditions: voltage variations, dips and short interruptions ....................................................... 11

4.3.3 Voltage transients ....................................................................................................................................... 12

4.3.3.1 Voltage transient due to short-circuit and protective device clearance ................................................. 12

4.3.3.2 Short voltage transient due to switching and lightning ......................................................................... 12

4.3.4 Recovery from voltage transients ............................................................................................................... 13

4.4 Voltage changes due to the regulation of the power supply ............................................................................. 14

4.5 Power supply protection at interface "A" ......................................................................................................... 14

4.6 Maximum current drain .................................................................................................................................... 14

4.7 Inrush Current on connection of interface "A" ................................................................................................. 15

4.7.1 Limits .......................................................................................................................................................... 15

4.7.2 Measurements ............................................................................................................................................. 16

4.8 Conducted immunity requirements of the ICT equipment at interface "A": narrowband noise ....................... 17

4.9 Conducted emissions requirements of the ICT equipment at interface "A" ..................................................... 19

5 Earthing and bonding ............................................................................................................................. 20

Annex A (informative): Identification of interface "A" ...................................................................... 21

Annex B (informative): -60 VDC systems ............................................................................................ 22

Annex C (informative): Guide for measuring inrush current and for transferring the

recorded pulses onto the limit chart ............................................................. 23

C.1 Measurement .......................................................................................................................................... 23

C.2 Pulse waveform transfor mation .............................................................................................................. 23

C.3 Measurement of inrush current with filter capacitor current pulses ....................................................... 26

Annex D (informative): Test arrangements for the injection of electrical noise at interface

"A" .................................................................................................................. 29

Annex E (informative): Wideband noise .............................................................................................. 30

E.0 Wideband noise ...................................................................................................................................... 30

E.1 Emission of wideband noise ................................................................................................................... 30

E.1.0 General ............................................................................................................................................................. 30

E.1.1 Assessment of wideband noise ......................................................................................................................... 30

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)

E.2 How to calculate wideband emission ..................................................................................................... 30

Annex F (informative): Protection dimensioning ................................................................................ 34

Annex G (informative): Effects of protective device operation transients in the power

distribution ..................................................................................................... 35

Annex H (informative): Bibliography ................................................................................................... 36

History .............................................................................................................................................................. 37

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This draft European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE),

and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN Approval Procedure.

The present document concerns the requirements for the interface between ICT equipment and its power supply, and

includes requirements relating to its stability and measurement. Various other references and detailed measurement and

test arrangements are contained in informative annexes.

The present document is part 2 of a multi-part deliverable covering Environmental Engineering (EE); Power supply

interface at the input to Information and Communication Technology (ICT) equipment, as identified below:

Part 1: "Alternating Current (AC)";
Part 2: "-48 V Direct Current (DC)";
Part 3: "Up to 400 V Direct Current (DC)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
1 Scope

The present document contains requirements and measurements methods for the physical interface "A" that is situated

between the power supply system(s) and the power consuming ICT equipment.

The nominal voltage at power interface "A" of ICT equipment defined in the present document is DC voltage -48 V.

The DC power can be supplied by a DC output power system (e.g. based on AC rectifiers on grid or DC/DC converters on

solar system, fuel cell, DC engine or fuel cell generator) and also directly supplied by a battery backup in this DC power

system. The purpose of the present document is to use a power supply system with the same characteristics for all ICT

equipment defined in the area of application:
- to facilitate inter working of different types of load units;
- to facilitate the standardization of ICT equipment;

- to facilitate the installation, operation and maintenance in the same network of ICT equipment and systems

from different origins.

The present document aims at providing electrical compatibility between the power supply equipment and the power

consuming ICT equipment, between different system blocks and loads connected to the same power supply feeding the

interface "A" (e.g. control/monitoring, cooling system, etc.).
The requirements are defined for:

- the power supply input of any type of ICT equipment installed at telecommunication centres that are connected

to interface "A" powered by DC;

- any type of ICT equipment, installed in access networks and customers' premises, the DC interface "A" of

which is also used by equipment requiring a DC supply source;

- any type of ICT equipment powered by DC, used in the fixed and mobile networks installed in different

locations such as buildings, shelters, street cabinets.

Disturbances on the power supply interface "A" relating to the continuous wave phenomena below 20 kHz are covered

within the present document.

The present document does not cover safety requirements, they are covered by relevant safety standards.

The present document does not cover EMC requirements, they are covered by relevant EMC standards.

NOTE: Annex B gives guidance on -60 VDC supply systems.
2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] Void.
[2] Void.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
[3] Void.
[4] Void.

[5] CENELEC EN 61000-4-5: "Electromagnetic compatibility (EMC) - Part 4-5: Testing and

measurement techniques - Surge immunity test".
[6] Void.

[7] CENELEC EN 61000-4-29: "Electromagnetic compatibility (EMC) - Part 4-29: Testing and

measurement techniques -Voltage dips, short interruptions and voltage variations on d.c. input

power port immunity tests".
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Recommendation ITU-T Q.551: "Transmission characteristics of digital exchanges".

[i.2] Recommendation ITU-T Q.552: "Transmission characteristics at 2-wire analogue interfaces of

digital exchanges".

[i.3] Recommendation ITU-T Q.553: "Transmission characteristics at 4-wire analogue interfaces of

digital exchanges".

[i.4] Recommendation ITU-T Q.554: "Transmission characteristics at digital interfaces of digital

exchanges".

[i.5] ETSI TR 100 283: "Environmental Engineering (EE); Transient voltages at Interface "A" on

telecommunications direct current (dc) power distributions".

[i.6] US Department of Defence MIL-STD-461E: "Requirements for the control of electromagnetic

interference characteristics of subsystems and equipment".

[i.7] ETSI EN 300 253: "Environmental Engineering (EE); Earthing and bonding of ICT equipment

powered by -48 VDC in telecom and data centres".

[i.8] Recommendation ITU-T O.41: "Psophometer for use on telephone-type circuits".

[i.9] IEC 60050-601: "International Electrotechnical Vocabulary. Chapter 601: Generation,

transmission and distribution of electricity - General" (Area 826 "Electrical installations",

section 826-11 "Voltages and currents").
[i.10] CENELEC EN 60269-1: "Low-voltage fuses - Part 1: General requirements".
[i.11] CENELEC EN 60934: "Circuit-breakers for equipment (CBE)".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:

abnormal service voltage range: range of steady-state voltage over which the equipment will not be expected to

maintain normal service but will survive undamaged
customer premises: location which is the sole responsibility of the customer
DC power return conductor: 0 V power supply conductor
NOTE: Also called "battery return".

fully equipped equipment: configuration that corresponds to the maximum power consumption measured at -48 VDC

with the equipment in operating conditions (e.g. not in standby mode)

NOTE: When there are several fully equipped configurations because of different combinations of possible

boards, the configuration with the boards that gives the highest power consumption should be considered.

ICT equipment: device, in the telecommunication network infrastructure, that provides an ICT service

interface "A": terminals at which the power supply is connected to the system block

NOTE 1: See also figure 1 and annex A.

NOTE 2: This is a functional definition and not an exact depiction of the physical location.

malfunction: termination of the normal service

maximum steady state input current (I ): maximum steady state input current, stated by the manufacturer, for a fully

equipped equipment under test connected to interface "A" at nominal voltage

nominal voltage: value of the voltage by which the electrical installation or part of the electrical installation is

designated and identified [i.9]

normal service: service mode where ICT equipment operates within its specification which includes a defined restart

time after malfunction or full interruption

normal service voltage range: range of steady-state voltages over which the equipment will maintain normal service

power supply: power source to which ICT equipment is intended to be connected

service voltage: value of the voltage under normal conditions, at a given instant and a given point of the system [i.9]

system block: functional group of equipment depending for its operation and performance on its connection to the same

power supply

NOTE: A system block may consist of equipment or a functional group of equipment. Different examples of

configurations at interface "A" are given in annex A.

telecommunication centre: location where ICT equipment is installed and which is the sole responsibility of the

operator
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
3.2 Symbols
For the purposes of the present document, the following symbols apply:
I instantaneous inrush current
I maximum steady state input current
L inductance of inductive element of LISN
R resistance of resistive element of LISN
t time
pso,eff effective psophometric voltage
rms RMS voltage
Z capacitive impedance of immunity measurement circuit
Z resistive impedance of immunity measurement circuit
μs microsecond
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
DC Direct Current
NOTE: Also when used as a suffix to units of measurement.
EMC ElectroMagnetic Compatibility
ESR Equivalent Series Resistance
EUT Equipment Under Test
HOD High-Ohmic Distributions
ICT Information and Communication Technology
LISN Line Impedance Stabilization Network
LOD Low-Ohmic Distributions
RF Radio Frequency
rms root mean square
TR Technical Report
VDC Voltage Direct Current
NOTE: Also when used as a suffix to units of measurement.
4 Requirements
4.0 Power interface "A"

The power supply interface, interface "A" of figure 1, is a physical point to which all the requirements are related.

This point is situated between the power supply system(s) and the power consuming ICT equipment.

An example of a configuration in which interface "A" is identified is given in annex A.

ETSI
---------------------- Page: 9 ----------------------
10 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
ICT equipment
Figure 1: Identification of interface "A"
4.1 Nominal voltage

The interface and equipment shall be designated and identified by a nominal voltage.

The nominal voltage at interface "A" shall be -48 VDC with positive conductor connected to earth as defined in ETSI

EN 300 253 [i.7].

NOTE 1: The positive conductor, also called DC return, can be (see ETSI EN 300 253 [i.7]:

 Isolated DC return: this is a DC power system in which the DC power return conductor has a single

point connection to the bonding network. Equipment intended for this power distribution has a

floating DC power at the power input terminal.

 Common DC return: this is a DC power system in which the return conductor is connected to the

bonding network at many points. Equipment intended for this power distribution can have the DC

return earthed at the power input terminal.

NOTE 2: In most cases the nominal voltage of interface "A" is based on a 24 cells lead-acid battery. Use of other

technologies, such as Lithium-ion batteries, are increasing.
4.2 Normal service voltage range at interface "A"

The normal service voltage range for the -48 VDC nominal supply at interface "A" shall be from -40,5 VDC

to -57,0 VDC.

There shall be no degradation of service performance when ICT equipment is operating at voltages within the normal

service voltage range including voltage variation inside the normal voltage range.

This requirement shall be verified by applying at interface "A" a voltage step test with specification and parameters

defined in table 1. The testing and measurement techniques are described in CENELEC EN 61000-4-29 [7].

The test shall apply to equipment with single and multiple power supply "A" interface inputs.

ETSI
---------------------- Page: 10 ----------------------
11 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
Table 1

Test level of Normal Voltage Basic standard Rise and fall time of Performance criteria

service voltage step step for testing voltage step
variation Duration
From -40,5 V to -57,0 VDC 0,1 s CENELEC No degradation in the
Between 1 μs and 50 μs on

From -57,0 V to -40,5 VDC 0,1 s EN 61000-4-29 [7] 100 Ω resistive load service performance

during and after the
(see basic standard for test
test
generator)

In the case of ICT equipment with power supply input redundancy (e.g. Input 1 and Input 2), this test shall be

performed:

• with Inputs 1 and 2 powered simultaneously and applying the test in table 1 on both inputs simultaneously;

• with Inputs 1 and 2 powered simultaneously and applying the test in table 1 on one input (either Input 1 or 2);

• with either Input 1 or 2 powered and no power on the other power input and applying the test in table 1 on the

powered input.

NOTE 1: The minimum voltage is based on the voltage drop in the distribution network and a battery cell end of

discharge voltage.

NOTE 2: The voltages specified are measured at interface "A". It should be noted that if interface "A" is at any

point other than the ICT equipment interface as presented in annex A, there will be a voltage drop

between interface "A" and the equipment terminals.
4.3 Abnormal service voltage range at interface "A"
4.3.1 Abnormal service voltage range under steady state conditions

ICT equipment designed to work at 48 VDC nominal voltage at the interface "A" shall not suffer any damage when

subjected to the following voltage ranges defined in table 2.
Table 2
0,0 V to -40,5 VDC and
-57,0 VDC to -60,0 VDC

Following the restoration of the supply to the normal voltage range, the power conversion and management systems on

the load side of interface "A" shall automatically restore normal service. The ICT equipment shall then resume

operation according to its specifications. The abnormal service voltage shall not lead to the disconnection of the power

supply e.g. by causing circuit breakers, fuses or other such devices to operate.

NOTE: It is acceptable that the system may restart when the voltage is -40,5 VDC or anywhere within the

nominal service voltage range and/or after a time delay.
4.3.2 Abnormal conditions: voltage variations, dips and short interruptions

ICT equipment shall comply with the requirements defined in this clause when subject to the abnormal voltage range

defined in table 3 that can be present at the interface "A".

This requirement shall be verified by applying at interface "A" a voltage step test with specification and parameters

defined in table 3. The testing and measurement techniques are described in CENELEC EN 61000-4-29 [7].

The test shall apply to equipment with single and multiple power supply inputs.
ETSI
---------------------- Page: 11 ----------------------
12 Draft ETSI EN 300 132-2 V2.5.9 (2019-01)
Table 3

Test level of abnormal Voltage step Basic standard Rise and fall time of Performance criteria

voltage step variation Duration for testing voltage step
From -40,5 VDC to -60,0 VDC 0,1 s CENELEC Self restart to a normal
Between 1 μs and 50 μs
and from -60 VDC to -40,5 VDC EN 61000-4-29 [7] service of the equipment
on 100 Ω resistive load
From -57,0 VDC to 0,0 V and 0,1 s (see basic standard) without operator
intervention after the test
from 0,0 V to -57,0 VDC

In the case of ICT equipment with power supply input redundancy (e.g. Input 1 and Input 2), this test shall be

performed:

• with Inputs 1 and 2 powered simultaneously and applying the test in table 3 on both inputs simultaneously;

• with Inputs 1 and 2 powered simultaneously and applying the test in table 3 on one input (either Input 1 or 2).

In this case the performance criteria shall be "No degradation in the service performance during and after the

test";

• with either Input 1 or 2 powered and no power on the other power input and applying the test in table 3 on the

powered input.
4.3.3 Voltage transients
4.3.3.1 Voltage transient due to short-circuit and protective device clearance

Voltage transients may occur at interface "A" when faults (e.g. short circuits) occur in the power distribution system.

These transients are characterized by a voltage drop in the range: 0 V to -40,5 VDC, followed by an overvoltage often

in excess of the maximum steady state abnormal service voltage range defined in table 3 and dependent upon the power

distribution up to interface "A" and the equipment connected to interface "A".

NOTE 1: ETSI TR 100 283 [i.5] provides guidance for the protection of ICT equipment from the transients.

NOTE 2: A protective device operation transient results from a low impedance fault to ground on the equipment

side of a protective device (fuse or circuit breaker) connected to a power distribution bus. In the power

bus, then voltage is reduced (undervoltage) due to high current flowing to ground through the protective

device and the short ground. When the protective device opens, the release energy stored in the

inductance of the bus causes an initial high voltage overshoot of short duration, followed by a longer

interval voltage
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.