ETSI EN 301 489-54 V1.1.1 (2022-10)

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 54: Specific conditions for fixed ground based aeronautical and meteorological radars; Harmonised Standard for electromagnetic compatibility

DEN/ERM-EMC-401

Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 54. del: Posebni pogoji za pritrjene zemeljske aeronavtične in meteorološke radarje - Harmonizirani standard za elektromagnetno združljivost

Ta dokument določa tehnične lastnosti in metode merjenja za v zvezi z elektromagnetno združljivostjo (EMC) za naslednje radarske sisteme:
• pritrjeni in zemeljski monostatični aeronavtični primarni nadzorni radar (PSR) in radar za površinsko gibanje (SMR);
• pritrjeni in zemeljski monostatični meteorološki radarski sistem (npr. vremenski radarski sistemi ali naprava za ugotavljanje profila vetra z naslednjimi značilnostmi:
• delovanje v vsaj enem od frekvenčnih območij, prikazanih v preglednici 1;
• delovanje izključno z izmeničnim tokom.
Zgoraj omenjena radijska oprema je namenjena za uporabo na fiksni lokaciji (stalni ali začasni) in vključuje vrtljive pasivne antene.
Radarski sistem je sestavljen iz enega ali več ohišij, ki zajemajo vsaj naslednje radarske funkcije: oddajnik, sprejemnik, obdelava signala. Drugi deli, ki nimajo radarske funkcije (npr. lokalni sistem UPS, oprema za klimatizacijo, oprema za razvlaževanje, komunikacijska omrežna oprema itd.), ne spadajo na področje uporabe tega dokumenta, razen če so ti deli nameščeni v ohišju oziroma ohišjih radarskega sistema.
Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskih vhodom radijske opreme.
Te tehnične specifikacije so navedene v ustreznih standardih za izdelke v skladu s členom 3.2 Direktive 2014/53/EU [i.1].
Zahteve glede sevanja v tem dokumentu so določene za frekvence nad 9 kHz.
Okoljska razvrstitev ter zahteve glede sevanja in odpornosti iz tega dokumenta so
navedene v standardu ETSI EN 301 489-1 [1], razen posebnih pogojev iz tega dokumenta.
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami iz člena 3.1(b)
Direktive 2014/53/EU [i.1] je podano v dodatku A.

General Information

• Status: Not Published
• Technical Committee: ERM WGEMC - ERM Electromagnetic Compatibility
• Current Stage: 12 - Completion
• Due Date: 18-Sep-2020
• Ref Project: SIST EN 301 489-54 V1.1.1:2023 - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 54: Specific conditions for fixed ground based aeronautical and meteorological radars - Harmonised Standard for electromagnetic compatibility

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 301 489-54 V1.1.1:2023
01-januar-2023
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 54.
del: Posebni pogoji za pritrjene zemeljske aeronavtične in meteorološke radarje -
Harmonizirani standard za elektromagnetno združljivost
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part
54: Specific conditions for fixed ground based aeronautical and meteorological radars -
Harmonised Standard for electromagnetic compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-54 V1.1.1 (2022-10)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 489-54 V1.1.1:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 489-54 V1.1.1:2023

---------------------- Page: 2 ----------------------
SIST EN 301 489-54 V1.1.1:2023
ETSI EN 301 489-54 V1.1.1 (2022-10)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 54: Specific conditions for fixed ground based
aeronautical and meteorological radars;
Harmonised Standard for electromagnetic compatibility

---------------------- Page: 3 ----------------------
SIST EN 301 489-54 V1.1.1:2023

2 ETSI EN 301 489-54 V1.1.1 (2022-10)

Reference
DEN/ERM-EMC-401
Keywords
aeronautical, EMC, harmonised standard,
measurement, radar

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
SIST EN 301 489-54 V1.1.1:2023

3 ETSI EN 301 489-54 V1.1.1 (2022-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Test conditions . 9
4.1 General requirements . 9
4.2 Arrangements for test signals . 9
4.2.1 Arrangements for test signals at the input of transmitters . 9
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 10
4.2.4 Arrangements for test signals at the output of receivers . 10
4.3 RF exclusion band for radio equipment . 10
4.3.1 General requirements . 10
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 10
4.3.3 Exclusion band for receivers or the receiver part of the transceivers . 10
4.4 Normal test modulation . 11
5 Performance Assessment . 11
5.1 General requirements . 11
6 Performance criteria . 11
6.1 General requirements . 11
7 Applicability tables. 12
7.1 EMC Emission . 12
7.1.1 General requirements . 12
7.1.2 Special Conditions . 13
7.2 Immunity . 13
7.2.1 General requirements . 13
7.2.2 Special Conditions . 14
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 15
Annex B (normative): Acceptable Degraded Performance corresponding to Performance
Criteria B . 17
History . 18


ETSI

---------------------- Page: 5 ----------------------
SIST EN 301 489-54 V1.1.1:2023

4 ETSI EN 301 489-54 V1.1.1 (2022-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 54 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 29 September 2022
Date of latest announcement of this EN (doa): 31 December 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2023
Date of withdrawal of any conflicting National Standard (dow): 30 June 2024

ETSI

---------------------- Page: 6 ----------------------
SIST EN 301 489-54 V1.1.1:2023

5 ETSI EN 301 489-54 V1.1.1 (2022-10)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 7 ----------------------
SIST EN 301 489-54 V1.1.1:2023

6 ETSI EN 301 489-54 V1.1.1 (2022-10)
1 Scope
The present document specifies technical characteristics and methods of measurement in respect of ElectroMagnetic
Compatibility (EMC) for the following radar systems:
• Fixed and ground based monostatic aeronautical Primary Surveillance Radar (PSR) and Surface Movement
Radar (SMR)
• Fixed and ground based monostatic meteorological radar system, for example weather radar systems or wind
profiler
with the following characteristics:
• operating in at least one of the frequency ranges as shown in table 1;
• operated only by AC power.
The above mentioned radio equipment is intended to be used at a fixed location (permanent or temporarily) and is
equipped with rotating passive antennas.
A radar system consists of one or more enclosures that contain at least the following radar functionalities: transmitter,
receiver, signal processing. Other parts which are not part of the radar functionality e.g. local UPS, air conditioning
equipment, dehumidifying equipment, communication network equipment, etc., are not in the scope of the present
document, unless these parts are implemented inside the radar system enclosure(s).
Table 1: Frequency range of fixed ground based aeronautical
and meteorological radar systems
Operating frequency ranges
1 215 MHz to 1 400 MHz
2 700 MHz to 3 100 MHz
5 250 MHz to 5 850 MHz
8 500 MHz to 10 500 MHz

Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards under article 3.2 of Directive 2014/53/EU [i.1].
Emission requirements in the present document are specified for frequencies above 9 kHz.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of
Directive 2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
SIST EN 301 489-54 V1.1.1:2023

7 ETSI EN 301 489-54 V1.1.1 (2022-10)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "Electro Magnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ITU Radio Regulations (2020).
[i.4] EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements", (produced by CENELEC).
[i.5] Recommendation ITU-R SM.1541-6 (08/2015): "Unwanted emissions in the out-of-band domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document the following terms apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
 the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
 the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
 the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
antenna port: port, for connection of an antenna used for intentional transmission and/or reception of radiated RF
energy
ETSI

---------------------- Page: 9 ----------------------
SIST EN 301 489-54 V1.1.1:2023

8 ETSI EN 301 489-54 V1.1.1 (2022-10)
centre frequency (f ): centre of the transmitter necessary bandwidth
c
critical stored data: data that is essential for an EUT to perform
...

ETSI EN 301 489-54 V1.1.1 (2022-10)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 54: Specific conditions for fixed ground based
aeronautical and meteorological radars;
Harmonised Standard for electromagnetic compatibility

---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-54 V1.1.1 (2022-10)

Reference
DEN/ERM-EMC-401
Keywords
aeronautical, EMC, harmonised standard,
measurement, radar

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-54 V1.1.1 (2022-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Test conditions . 9
4.1 General requirements . 9
4.2 Arrangements for test signals . 9
4.2.1 Arrangements for test signals at the input of transmitters . 9
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 10
4.2.4 Arrangements for test signals at the output of receivers . 10
4.3 RF exclusion band for radio equipment . 10
4.3.1 General requirements . 10
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 10
4.3.3 Exclusion band for receivers or the receiver part of the transceivers . 10
4.4 Normal test modulation . 11
5 Performance Assessment . 11
5.1 General requirements . 11
6 Performance criteria . 11
6.1 General requirements . 11
7 Applicability tables. 12
7.1 EMC Emission . 12
7.1.1 General requirements . 12
7.1.2 Special Conditions . 13
7.2 Immunity . 13
7.2.1 General requirements . 13
7.2.2 Special Conditions . 14
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 15
Annex B (normative): Acceptable Degraded Performance corresponding to Performance
Criteria B . 17
History . 18


ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-54 V1.1.1 (2022-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 54 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 29 September 2022
Date of latest announcement of this EN (doa): 31 December 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2023
Date of withdrawal of any conflicting National Standard (dow): 30 June 2024

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-54 V1.1.1 (2022-10)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-54 V1.1.1 (2022-10)
1 Scope
The present document specifies technical characteristics and methods of measurement in respect of ElectroMagnetic
Compatibility (EMC) for the following radar systems:
• Fixed and ground based monostatic aeronautical Primary Surveillance Radar (PSR) and Surface Movement
Radar (SMR)
• Fixed and ground based monostatic meteorological radar system, for example weather radar systems or wind
profiler
with the following characteristics:
• operating in at least one of the frequency ranges as shown in table 1;
• operated only by AC power.
The above mentioned radio equipment is intended to be used at a fixed location (permanent or temporarily) and is
equipped with rotating passive antennas.
A radar system consists of one or more enclosures that contain at least the following radar functionalities: transmitter,
receiver, signal processing. Other parts which are not part of the radar functionality e.g. local UPS, air conditioning
equipment, dehumidifying equipment, communication network equipment, etc., are not in the scope of the present
document, unless these parts are implemented inside the radar system enclosure(s).
Table 1: Frequency range of fixed ground based aeronautical
and meteorological radar systems
Operating frequency ranges
1 215 MHz to 1 400 MHz
2 700 MHz to 3 100 MHz
5 250 MHz to 5 850 MHz
8 500 MHz to 10 500 MHz

Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards under article 3.2 of Directive 2014/53/EU [i.1].
Emission requirements in the present document are specified for frequencies above 9 kHz.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of
Directive 2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-54 V1.1.1 (2022-10)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "Electro Magnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ITU Radio Regulations (2020).
[i.4] EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements", (produced by CENELEC).
[i.5] Recommendation ITU-R SM.1541-6 (08/2015): "Unwanted emissions in the out-of-band domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document the following terms apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
 the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
 the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
 the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
antenna port: port, for connection of an antenna used for intentional transmission and/or reception of radiated RF
energy
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-54 V1.1.1 (2022-10)
centre frequency (f ): centre of the transmitter necessary bandwidth
c
critical stored data: data that is essential for an EUT to perform a primary function in accordance with that EUT's
specification
NOTE: This may include data previously stored by the user.
enclosure port: physical boundary of the equipment through which electromagnetic fields may radiate or impinge
NOTE: Also known as cabinet radiation.
Equipment Under Test (EUT): equipment subject to the performance requirements of the present document
mode of operation: operational status of the radar system, for example but not limited to standby or operati
...

Draft ETSI EN 301 489-54 V1.0.1 (2022-07)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 54: Specific conditions for fixed ground based
aeronautical and meteorological radars;
Harmonised Standard for electromagnetic compatibility

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)

Reference
DEN/ERM-EMC-401
Keywords
aeronautical, EMC, harmonised standard,
measurement, radar

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Test conditions . 9
4.1 General requirements . 9
4.2 Arrangements for test signals . 9
4.2.1 Arrangements for test signals at the input of transmitters . 9
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 10
4.2.4 Arrangements for test signals at the output of receivers . 10
4.3 RF exclusion band for radio equipment . 10
4.3.1 General requirements . 10
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 10
4.3.3 Exclusion band for receivers or the receiver part of the transceivers . 10
4.4 Normal test modulation . 11
5 Performance Assessment . 11
5.1 General requirements . 11
6 Performance criteria . 11
6.1 General requirements . 11
7 Applicability tables. 12
7.1 EMC Emission . 12
7.1.1 General requirements . 12
7.1.2 Special Conditions . 12
7.2 Immunity . 13
7.2.1 General requirements . 13
7.2.2 Special Conditions . 13
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 15
Annex B (normative): Acceptable Degraded Performance corresponding to Performance
Criteria B . 17
History . 18


ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM) and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 54 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
1 Scope
The present document specifies technical characteristics and methods of measurement in respect of ElectroMagnetic
Compatibility (EMC) for the following radar systems:
• Fixed and ground based monostatic aeronautical Primary Surveillance Radar (PSR) and Surface Movement
Radar (SMR)
• Fixed and ground based monostatic meteorological radar system, for example weather radar systems or wind
profiler
with the following characteristics:
• operating in at least one of the frequency ranges as shown in table 1;
• operated only by AC power.
The above mentioned radio equipment is intended to be used at a fixed location (permanent or temporarily) and is
equipped with rotating passive antennas.
A radar system consists of one or more enclosures that contain at least the following radar functionalities: transmitter,
receiver, signal processing. Other parts which are not part of the radar functionality e.g. local UPS, air conditioning
equipment, dehumidifying equipment, communication network equipment, etc., are not in the scope of the present
document, unless these parts are implemented inside the radar system enclosure(s).
Table 1: Frequency range of fixed ground based aeronautical
and meteorological radar systems
Operating frequency ranges
1 215 MHz to 1 400 MHz
2 700 MHz to 3 100 MHz
5 250 MHz to 5 850 MHz
8 500 MHz to 10 500 MHz

Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards under article 3.2 of Directive 2014/53/EU [i.1].
Emission requirements in the present document are specified for frequencies above 9 kHz.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of
Directive 2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "Electro Magnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ITU Radio Regulations (2020).
[i.4] EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements", (produced by CENELEC).
[i.5] Recommendation ITU-R SM.1541-6 (08/2015): "Unwanted emissions in the out-of-band domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document the following terms apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
 the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
 the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
 the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
antenna port: port, for connection of an antenna used for intentional transmission and/or reception of radiated RF
energy
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
centre frequency (f ): centre of the transmitter necessary bandwidth
c
critical stored data: data that is essential for an EUT to perform a primary function in accordance with that EUT's
specification
NOTE: This may include data previously stored by the user.
enclosure port: physical boundary of the equipment through which electromagnetic fields may radiate or impinge
NOTE: Also known as cabinet radiation.
Equipment Under Test (EUT): equipment subject to the performance requirements of the present document
mode of operation: operational status of the ra
...

SLOVENSKI STANDARD
oSIST prEN 301 489-54 V1.0.1:2022
01-september-2022
Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 54.
del: Posebni pogoji za pritrjene zemeljske aeronavtične in meteorološke radarje -
Harmonizirani standard za elektromagnetno združljivost
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part
54: Specific conditions for fixed ground based aeronautical and meteorological radars -
Harmonised Standard for electromagnetic compatibility
Ta slovenski standard je istoveten z: ETSI EN 301 489-54 V1.0.1 (2022-07)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 301 489-54 V1.0.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

---------------------- Page: 2 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022
Draft ETSI EN 301 489-54 V1.0.1 (2022-07)






HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 54: Specific conditions for fixed ground based
aeronautical and meteorological radars;
Harmonised Standard for electromagnetic compatibility

---------------------- Page: 3 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

2 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)

Reference
DEN/ERM-EMC-401
Keywords
aeronautical, EMC, harmonised standard,
measurement, radar

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

3 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Test conditions . 9
4.1 General requirements . 9
4.2 Arrangements for test signals . 9
4.2.1 Arrangements for test signals at the input of transmitters . 9
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 10
4.2.4 Arrangements for test signals at the output of receivers . 10
4.3 RF exclusion band for radio equipment . 10
4.3.1 General requirements . 10
4.3.2 Exclusion band for transmitters or the transmitter part of transceivers. 10
4.3.3 Exclusion band for receivers or the receiver part of the transceivers . 10
4.4 Normal test modulation . 11
5 Performance Assessment . 11
5.1 General requirements . 11
6 Performance criteria . 11
6.1 General requirements . 11
7 Applicability tables. 12
7.1 EMC Emission . 12
7.1.1 General requirements . 12
7.1.2 Special Conditions . 12
7.2 Immunity . 13
7.2.1 General requirements . 13
7.2.2 Special Conditions . 13
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 15
Annex B (normative): Acceptable Degraded Performance corresponding to Performance
Criteria B . 17
History . 18


ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

4 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM) and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 54 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

5 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 7 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

6 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
1 Scope
The present document specifies technical characteristics and methods of measurement in respect of ElectroMagnetic
Compatibility (EMC) for the following radar systems:
• Fixed and ground based monostatic aeronautical Primary Surveillance Radar (PSR) and Surface Movement
Radar (SMR)
• Fixed and ground based monostatic meteorological radar system, for example weather radar systems or wind
profiler
with the following characteristics:
• operating in at least one of the frequency ranges as shown in table 1;
• operated only by AC power.
The above mentioned radio equipment is intended to be used at a fixed location (permanent or temporarily) and is
equipped with rotating passive antennas.
A radar system consists of one or more enclosures that contain at least the following radar functionalities: transmitter,
receiver, signal processing. Other parts which are not part of the radar functionality e.g. local UPS, air conditioning
equipment, dehumidifying equipment, communication network equipment, etc., are not in the scope of the present
document, unless these parts are implemented inside the radar system enclosure(s).
Table 1: Frequency range of fixed ground based aeronautical
and meteorological radar systems
Operating frequency ranges
1 215 MHz to 1 400 MHz
2 700 MHz to 3 100 MHz
5 250 MHz to 5 850 MHz
8 500 MHz to 10 500 MHz

Technical specifications related to the antenna port of the radio equipment are not included in the present document.
Such technical specifications are found in the relevant product standards under article 3.2 of Directive 2014/53/EU [i.1].
Emission requirements in the present document are specified for frequencies above 9 kHz.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of
Directive 2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

7 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.2.3) (11-2019): "Electro Magnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard for
ElectroMagnetic Compatibility".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ITU Radio Regulations (2020).
[i.4] EN 55032:2015: "Electromagnetic compatibility of multimedia equipment - Emission
Requirements", (produced by CENELEC).
[i.5] Recommendation ITU-R SM.1541-6 (08/2015): "Unwanted emissions in the out-of-band domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document the following terms apply:
ancillary equipment: electrical or electronic equipment, that is intended to be used with a receiver or transmitter
NOTE 1: It is considered as an ancillary equipment if:
 the equipment is intended for use with a receiver or transmitter to provide additional operational
and/or control features to the radio equipment (e.g. to extend control to another position or
location);
 the ancillary equipment cannot be used without being connected to radio equipment to provide user
functions independently of a receiver or transmitter; and
 the receiver or transmitter, to which it is connected, is capable of providing some intended
operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a
sub-unit of the main equipment essential to the main equipment basic functions).
NOTE 2: An example of ancillary equipment would be a docking station for radio equipment whose interface is
dedicated to a particular product or range of products.
antenna port: port, for connection of an antenna used for intentional transmission and/or reception of radiated RF
energy
ETSI

---------------------- Page: 9 ----------------------
oSIST prEN 301 489-54 V1.0.1:2022

8 Draft ETSI EN 301 489-54 V1.0.1 (2022-07)
centre frequency (f ): centre of the transmitter necessary bandwidth
c
cr
...